GE ATP 1000 Support Question
GE ATP 1000 Support Question
Find answers below for this question about GE ATP 1000 - Security Concord Alphanumeric Touchpad.Need a GE ATP 1000 manual? We have 1 online manual for this item!
Current Answers
Answer #1: Posted by waelsaidani1 on May 10th, 2016 10:34 AM
waelsaidani1
Member since:
May 12th, 2013 Points: 19,501,787
Member since:
May 12th, 2013 Points: 19,501,787
Related GE ATP 1000 Manual Pages
Installation Instructions - Page 1
... area (32°F to 120°F/0°C to indicate the current status of compatible security systems (see the "Specifications" section). The door can be reattached later if desired. ...anytime. See the panel installation instructions for cutting wallboard
Guidelines
• Mount the touchpad in speaker provides alarm, status, and button-press sounds. imum available power. • Table 1 ...
Installation Instructions - Page 2
... the mounting plate with the wall or gang box screw holes and secure the
back plate using the screws provided. 5. Separating the Touchpad from the mounting plate (see
Table 2). 3. Insert anchors into the bottom of the mount- Touchpad Wiring Connections
Attaching the Touchpad to the matching panel
terminals (see Figure 2). Installing the Mounting Plate...
Installation Instructions - Page 3
... an alphanumeric touchpad as a permanent part of the touchpad.
7. Press A or B until the display shows SYSTEM PROGRAMMING.
9.
Then, use the appropriate procedure for the newly installed touchpad (such as a programming touchpad, be careful not to the Programming Touchpad Header (see the specific panel installation instructions. Caution
. Press ƒ and the display shows SECURITY...
Installation Instructions - Page 4
...correct this, change the touchpad unit number as described in the section "Changing the Touchpad Unit Number."...system master CODE. Press , and the display briefly shows DONE, then shows the time and date.
4
ATP1000 Touchpad/Display Installation...and the display shows TOUCHPAD BRIGHTNESS 2 (default setting). 4. Enter a setting from Concord panel memory before activating alarms, to delete the ...
Installation Instructions - Page 5
... panel terminals.
2. Check for at least 2 seconds. The display shows DA n,
where n is in Concord RF systems. 5. Press ƒ.
The bus failure will clear after successfully changing the touchpad unit number.
2. If necessary, change the touchpad unit number:
1. At the touchpad, press and hold the D and 6 buttons together for correct bus wiring connections (green and white...
Installation Instructions - Page 6
... and any bus device. FCC Part 15 Class B
This equipment has been tested and found to another system touchpad and enter 8 + installer/dealer CODE (default = 4321) + 0 + 1. These limits are installing. Concord is the only installed touchpad, remove panel AC and battery power, then re-apply power. All other bus devices should be determined by...
Similar Questions
Add 3 New Employees To Alarm Code?
i cant seem to find how to add 3 new employees to alarm codes. can you help me or do i need to call ...
i cant seem to find how to add 3 new employees to alarm codes. can you help me or do i need to call ...
(Posted by karenhassell 9 years ago)
How Do I Set Realtor Alarm Code? Thanks
(Posted by Anonymous-146449 9 years ago)
P1 Code
I have a P1 code on my alarm panel and the chime continues to go off every minute or so. What is wro...
I have a P1 code on my alarm panel and the chime continues to go off every minute or so. What is wro...
(Posted by swuamett 11 years ago)
Help- I Moved Into A House And I Don't Have The Alarm Code. Won't Stop Beeping
(Posted by elisarooks 11 years ago)
How Do We Disarm Our System And When Do We Type In Security Code?
(Posted by carolyn2707 13 years ago)