GE ATP 1000 Support Question
GE ATP 1000 Support Question
Find answers below for this question about GE ATP 1000 - Security Concord Alphanumeric Touchpad.Need a GE ATP 1000 manual? We have 1 online manual for this item!
Question posted by stepharice on January 11th, 2011
P1
what does p1 on the display mean? it was never there before and now it is.
Current Answers
Related GE ATP 1000 Manual Pages
Installation Instructions - Page 1
...32°F to 120°F/0°C to indicate the current status of compatible security systems (see the "Specifications" section).
The door can be activated anytime. ... Needed
• 4-conductor, 22- The large 2-line, 16-character display provides easy to read messages to 49°C). • When mounting the touchpad, allow at least 3 inches below it past its stop point. '...
Installation Instructions - Page 2
... the touchpad.
2
ATP1000 Touchpad/Display Installation ...Instructions
Gently tighten the screw into the wall at the top of the mounting plate with the wall or gang box screw holes and secure the
back plate using the screws provided. 5. Separating the Touchpad from the panel to 22-gauge wire from the Mounting Plate
2.
Loosen screw,
then lift touchpad...
Installation Instructions - Page 3
... installer/dealer code (default = 4321) + 0 + 0. ATP1000 Touchpad/Display Installation Instructions
3 Press ƒ and the display shows SECURITY. 5. Verify that don't include an alphanumeric touchpad as a programming touchpad, be careful not to a Concord Express, Concord, or Concord Ultra panel with the cable). After verifying the touchpad device ID, press , repeatedly until the...
Installation Instructions - Page 4
... shows the time and date.
4
ATP1000 Touchpad/Display Installation Instructions To correct this, change the touchpad unit number as described in the touchpad location. Removing the programming touchpad from Concord panels with software versions 1.0-1.6 display USER CODES.)
2. Press ƒ.
Press B twice and the display shows TOUCHPAD BRIGHTNESS 2 (default setting). 4. Exit user programming...
Installation Instructions - Page 5
... at least 2 seconds. Make sure touchpad unit number is plugged in Concord RF systems. 5. At the touchpad, press and hold the D and 6 buttons together for correct bus wiring connections (green and white wires) at touchpad and panel terminals.
2. The display should show DA n, where n is the new touchpad unit number.
4. The display shows ENTER _. 3. Note If the...
Installation Instructions - Page 6
... and date display. FCC Part 15 Information to 120°F (49°C) Maximum Humidity 95% relative, non-condensing Dimensions 5.0" x 4.50" x 0.75" (L x W x D) UL Listings (all other names are trademarks of GE Interlogix. This equipment generates, uses, and can be cleared.
If this is a trademark of their owners.
Concord is the only installed touchpad, remove...
Similar Questions
How Do You Reset The Concord Express Security System
(Posted by paramn 9 years ago)
How To Reset Security Code Ge Concord Express
(Posted by bahstevej 9 years ago)
My Ge Atp 1000 Keypad Gets Blazing Hot. It Is Newly Installed Over Heating Duct.
Is it defective or does it need to be moved? Why would this happen?
Is it defective or does it need to be moved? Why would this happen?
(Posted by Axelrod6 10 years ago)
How To Set Time And Date On Ge Atp-1000 Keypad
(Posted by melodale 11 years ago)
I Have A Ge Atp 1000 Keypad. Can The Keypad Beeps Get Shut Off Or Lowered.
Also, is it possible to turning the beeping off when arming the system? Thanks, John
Also, is it possible to turning the beeping off when arming the system? Thanks, John
(Posted by jcangi01 12 years ago)