GE 60-806-95R-16Z Support Question
GE 60-806-95R-16Z Support Question
Find answers below for this question about GE 60-806-95R-16Z - Security Concord Express System Control Panel.Need a GE 60-806-95R-16Z manual? We have 1 online manual for this item!
Question posted by recou on March 25th, 2014
How To Override The Dealer Code On A Ge Security Concord Express
The person who posted this question about this GE product did not include a detailed explanation. Please use the "Request More Information" button to the right if more details would help you to answer this question.
Current Answers
Related GE 60-806-95R-16Z Manual Pages
Installation Instructions - Page 1
... d .
) *( 6HFXULW\
ZZZ*(6HFXULW\FRP Part No: 60-806 60-806-95R
466-1665 Rev G June 2004
T e s t S y s te m W e e k ly
O ff
A
1
p re s s b o th N o D e la y
B
4
p re s s b o th F e a tu re s
C
7
p re s s b o th
Q u ic k E x it
S ta tu s
D
*
S ta y 2
S ile n t 5
S y s te m 8
L ig h ts 0
A rm e d R eady
A w ay 3
6 M enu
9 B ypass
#
Concord Express
Installation Instructions
Installation Instructions - Page 6
...; Control Panel (60-806, 60-806-95R) • Backup Battery, 12 VDC, 4 AH (60-681) • SuperBus 2000 2x16 LCD Touchpad (60-746-01), SuperBus 2000 Fixed Display
Touchpad (60-820), SuperBus 2000 2x20 LCD Touchpad (60-803), or SuperBus 2000 2x20 VFD Touchpad (60-804) • Standard Class II 16.5 VAC, 25 VA Power Transformer; manufacturer-Tech Electro Ind, Inc. This security...
Installation Instructions - Page 9
...Panel
Determine the Panel Location
Before permanently mounting the panel, determine the location using the worksheets provided in programming to accept 2-wire smoke detectors.
• Built-In Radio Receiver: Allows use of GE Security 319.5 MHz. gramming access (not installer or dealer... section describes how to install the system control panel. Displays system messages, and indicates system ...
Installation Instructions - Page 13
... one of the HIM with the Concord™ Express panel has not been investigated by UL. Note Use of the following SnapCard models: • 8Z Input SnapCard-60-757 • 4 Output SnapCard-60-758 • 4Z Input/2 Output Combo SnapCard-60-756 Install the desired SnapCard onto the panel SnapCard Header and secure it in Figure . Both normally...
Installation Instructions - Page 14
...ohm, end-of -line resistor on all unused, factory programmed, onboard panel zones.
8642137A.DSF
To Zone Input Device (Shared Commons)
Figure 7....Panel Terminals 9
10
11
Normally Closed (N/C) Contacts in Series
Normally Open (N/O)
Contacts in the Concord Express
G N D +12V
3
4
A BUS B
5
6
Panel Terminals
Connecting Detection Devices to Panel Zone Inputs
The panel comes with panel...
Installation Instructions - Page 17
...or if the configuration of each onboard output. 15-Watt, Dual Tone Siren (13-469)
Panel terminal 7 (OUT1/+12V) is a +12V programmable output.
For more information on . At ...other than the default (00410), then the combined currents of each output. M. Black (Common)
Yellow (Steady)
GND
Concord Express Panel Terminals
3
O U T1/ +12V
7
Red (Not Used)
60806G 100D D S F
Figure 12. +12V...
Installation Instructions - Page 22
... securing the transformer to the outlet cover.
! For on each. 2. Connect the red, black, green, and white wires from the Programming Touchpad Cable (60... 8 + CODE + 0 + 0. This section describes how to the panel terminals:
1. After programming is powered up and disarmed. 3.
The touchpad shows SYSTEM PROGRAMMING. ¾ To enter programming mode using an installer/dealer code (default =...
Installation Instructions - Page 24
... flashes the entered setting.
2. Press ƒ and the display shows DEMO KIT OFF/ON (new setting).
3. Clear panel memory to learn all existing programming except the Dealer Code. Press ƒ and the display shows ENTER CODE TO CLEAR MEMORY.
3. Each menu on this feature and performing a memory clear changes the following settings: • System...
Installation Instructions - Page 25
...ƒ
once. The display should show SECURITY. Important ! Dealer Code is not set OR if the Dealer Code is used to partition 1 settings. If a dealer code is used from panel memory. CODE nnnnn (current code), enter the desired
Note
5-digit code, + ƒ. To change
code. Press ƒ and the display shows DOWN- Installer Code (0001)
Security-Global (Default = 4321)
The 4-digit...
Installation Instructions - Page 26
... entering the program mode with the installer code.
¾ To program a Dealer Code: 1. The display flashes the entered setting.
2. Account Number (0010)
Security-Partition 1 (Default = 00000)
The account number is used as panel (or customer) identification for users if this setting is on , the system arming level can be controlled by users if the setting is...
Installation Instructions - Page 28
... shows the new code.
¾ To delete a Duress Code:
1. To enter pauses, press C. SENSOR n (current sensor number), enter the desired sensor number (01-24).
The display shows PHONE NUMBER _.
23
Programming the Panel Keyswitch Sensor (0015)
Security-Partition 1 (Default = none)
This feature lets users arm and disarm the system using the Dealer Code. The following describes...
Installation Instructions - Page 39
..., touchpad panic alarms report using a 3-digit code from 500 to 503 with all GE Security panels, hardwire smoke detectors connected to the central monitoring station when the panel event buffer (memory) is nearly full.
...-Global (Default=off)
When this setting is turned on, the panel sends an "event buffer full" report to Concord or SnapCard hardwire zones do not send restorals.
¾ To ...
Installation Instructions - Page 48
... and calendar for September 1, 2000.
For example, enter 090100 for time and date.
Each security access code (Installer, Dealer, System Master, or User) must be unique.
3. The system master code default is disarmed. The display shows TIME AND DATE. The panel uses a 24-hour clock, eliminating the need to set the Time:
1. Enter the correct...
Installation Instructions - Page 54
...
000 001 - 024 600 - 615
678 679
System event not caused by a zone or user Sensor/Zone Numbers 1 - 24 Regular User Codes 0 - 15 used System Master Code used Installer Code used
680 Dealer Code used 697 Quick Arm used 698 Keyswitch Sensor used 699 System Armed Itself (during or within 15 seconds of any button...
Installation Instructions - Page 55
... perimeter and interior sensors are in the current arming level. Check that cannot be bypassed (group 26 fire sensors). 3. Note Clearing panel memory deletes factory zone programming. Use the Dealer Code to panel bus terminals or is powered up in user programming to see the ACCESSORY MODULES-BUS DEVICES
menu).
Attempting to 2-STAY or...
Installation Instructions - Page 56
..., if necessary. 9. For pagers, extend the pager delay setting (see the PHONE OPTIONS-GLOBAL menu in parallel for 16.5 VAC at panel terminals 1 and 2.
1. Check all phone troubleshooting Action/Solution steps. Verify Dealer Code matches ToolBox setting. 5. Check all phone troubleshooting Action/Solution steps. 2. System is plugged into an unswitched outlet. 2. Check that...
Installation Instructions - Page 63
... & (Default)
Shortcut No. cs phone 2 ___________
05005
Buffer Control (Off) Buffer Full Report (Off) Bypass Reports (Off)
05001 05006 05003
CS Phone 1 (None) CS Phone 2 (None) Call Wait Cancel (None)
0100 0110 02009
Appendix A: System Configuration Worksheets
58 Setting
Installer Programming-8 + Installer/Dealer CODE + 00
24-Hour Tamper
05000
AC Failure (Off)
05010...
Installation Instructions - Page 64
...)
09100
Output 2 (01710 - Failure (On)
02003
Daylight Savings (On)
0306
Dealer Code (None)
0002
Delete Sensors (None)
072
Dialer Abort (On)
02005
Dial Abort Delay (30 seconds)
02006...)
0150
DTMF Dialing (On)
02004
Duress Code (None)
0016
Duress Option (Off)
0514
Edit Sensors (None)
073
Entry Delay (30 seconds)
0310
Exit Delay (60 seconds)
0311
Exit Extension (On)
0013...
Installation Instructions - Page 71
... B: Programming Mode Menus and Settings
66 Underlined settings indicate defaults.
2. Appendix B: Programming Mode Menus and Settings
To enter Programming Mode:
8 + Installer or Dealer Code + 0 + 0
Tier 1 Menus TIER 1 MENUS
System Programming
TIER 2 MENUS
#
Security
#*
B Phones
A#
*
B Demo Kit On Off
A
B Clear Memory
A
B Exit
B
Programming
A
A
Press B to continue to Phone Options...
Installation Instructions - Page 73
... the unused zone from panel memory.
ID
n - Appendix C: Software Release Notes
68 SIA False Alarm defaults to Security Menu. B Sensors
A
#*
B
Accessory Modules A
#*
B Onboard Options
A
#*
Press B to return to on.
• SIA False Alarm control annunciating alarm level changes on exterior sirens. Using the Dealer Code for memory clear will include Downloader Code and CS Phone Numbers...
Similar Questions
How To Access The Dealer Code On Concord Express
(Posted by zacShinNe 9 years ago)
How To Reset Security Code Ge Concord Express
(Posted by bahstevej 10 years ago)
Concord Express Part No. 60-806 95r Clear Panel Memory
Cant find the code to clear panel memory to remove fault codes
Cant find the code to clear panel memory to remove fault codes
(Posted by redneckstill 10 years ago)
How To Reset Pass Code On Ge Alarm Concord Express
(Posted by mmaajch 10 years ago)
Security System 60-806-95r-16z
How can I permantly delete a sensor? Sayssensor 08 is not operating, but I only have 7 sensors.
How can I permantly delete a sensor? Sayssensor 08 is not operating, but I only have 7 sensors.
(Posted by lewann105 13 years ago)