User Guide
Page 11
If you need additional safety information concerning the WorkCentre or Xerox supplied materials, you may be burned. Scratches or smudges that concentration levels meet safe limits. Providing the correct environmental parameter, as you may shorten the ...: 1 - 800 - 828 - 6571 3 The ozone produced is dependent on the photoreceptor will result in the Xerox installation procedures, ensure that appear on copy volume and is heavier than air. Do not put your hands into the fuser area, as specified in poor copy quality and may call the following toll-free number...
If you need additional safety information concerning the WorkCentre or Xerox supplied materials, you may be burned. Scratches or smudges that concentration levels meet safe limits. Providing the correct environmental parameter, as you may shorten the ...: 1 - 800 - 828 - 6571 3 The ozone produced is dependent on the photoreceptor will result in the Xerox installation procedures, ensure that appear on copy volume and is heavier than air. Do not put your hands into the fuser area, as specified in poor copy quality and may call the following toll-free number...
User Guide
Page 16
... lowered (XD 104/ 130df/ 155df only). 9. They will occur if the fuser pins are not removed. Press the release lever to the Loading Paper section for additional information. • Do not fill above the max line. 8. Load paper into the WorkCentre. Push the paper tray firmly back into the tray. • Refer... to open the side cover. 10.Remove the Caution tape from the cover. 11.Remove the two red fuser pins by pulling the string upward one at a time. •...
... lowered (XD 104/ 130df/ 155df only). 9. They will occur if the fuser pins are not removed. Press the release lever to the Loading Paper section for additional information. • Do not fill above the max line. 8. Load paper into the WorkCentre. Push the paper tray firmly back into the tray. • Refer... to open the side cover. 10.Remove the Caution tape from the cover. 11.Remove the two red fuser pins by pulling the string upward one at a time. •...
User Guide
Page 44
Caution: Do not touch the shiny drum cartridge surface. Remove the misfed paper. 5. Fuser Area Exit Area Paper Feed Area 36 Paper Feed Area Note: Ensure that the alternate paper tray is lowered (XD104/ 105f/ 130df/ 155df only). 1. Scratches ... in the area, resulting in the direction shown. If paper cannot be removed, skip to open the side cover. - Press the release lever to the Fuser Area. 6. Carefully remove the misfed paper in smudged copies. 2.
Caution: Do not touch the shiny drum cartridge surface. Remove the misfed paper. 5. Fuser Area Exit Area Paper Feed Area 36 Paper Feed Area Note: Ensure that the alternate paper tray is lowered (XD104/ 105f/ 130df/ 155df only). 1. Scratches ... in the area, resulting in the direction shown. If paper cannot be removed, skip to open the side cover. - Press the release lever to the Fuser Area. 6. Carefully remove the misfed paper in smudged copies. 2.
User Guide
Page 45
...Path (continued) Fuser Area Warning: The fuser area is lowered (XD104 105f/ 130df/ 155df only). 1. Press the release lever to the Exit Area. Push up through the fusing unit. Close the side cover. 37 Take care when removing paper from the fuser area. Pull down on the fuser lever. •... This will release pressure on the fuser lever. 5. Remove the sheet of paper, in this area skip to open the side cover. 2. -...
...Path (continued) Fuser Area Warning: The fuser area is lowered (XD104 105f/ 130df/ 155df only). 1. Press the release lever to the Exit Area. Push up through the fusing unit. Close the side cover. 37 Take care when removing paper from the fuser area. Pull down on the fuser lever. •... This will release pressure on the fuser lever. 5. Remove the sheet of paper, in this area skip to open the side cover. 2. -...
User Guide
Page 46
Close the front cover and side cover. 38 Press the front cover release buttons to 1 open the side cover. 2. Push up on the paper. 4. Pull down on the fuser lever. • This will release pressure on the fuser lever. 7. Turn the knob in the direction of the arrow to move the paper to open the front cover. 3. Gently pull the paper out through the exit area. 6. Press the release lever to the exit area. 5. - E2 Clearing the Paper Path (continued) Exit Area 2 Note: Ensure that the alternate paper tray is lowered (XD104/105f/130df/155df only). 1.
Close the front cover and side cover. 38 Press the front cover release buttons to 1 open the side cover. 2. Push up on the paper. 4. Pull down on the fuser lever. • This will release pressure on the fuser lever. 7. Turn the knob in the direction of the arrow to move the paper to open the front cover. 3. Gently pull the paper out through the exit area. 6. Press the release lever to the exit area. 5. - E2 Clearing the Paper Path (continued) Exit Area 2 Note: Ensure that the alternate paper tray is lowered (XD104/105f/130df/155df only). 1.