User Guide
Page 11
The ozone produced is heavier than air. In the United States or Canada: 1 - 800 - 828 - 6571 3 Do not put your hands into the fuser area, as specified in the Xerox installation procedures, ensure that appear on copy volume and is dependent on the photoreceptor will result in poor copy quality and may shorten.... Safety Notes Do not touch the green photoreceptor. Scratches or smudges that concentration levels meet safe limits. If you need additional safety information concerning the WorkCentre or Xerox supplied materials, you may call the following toll-free number.
The ozone produced is heavier than air. In the United States or Canada: 1 - 800 - 828 - 6571 3 Do not put your hands into the fuser area, as specified in the Xerox installation procedures, ensure that appear on copy volume and is dependent on the photoreceptor will result in poor copy quality and may shorten.... Safety Notes Do not touch the green photoreceptor. Scratches or smudges that concentration levels meet safe limits. If you need additional safety information concerning the WorkCentre or Xerox supplied materials, you may call the following toll-free number.
User Guide
Page 16
... that the alternate paper tray is always open before opening the front cover. 12.Press the front cover release buttons to be needed if the WorkCentre has to open the side cover. 10.Remove the Caution tape from the cover. 11.Remove the two red.... They will occur if the fuser pins are not removed. Note: Ensure that the side cover is lowered (XD 104/ 130df/ 155df only). 9. Press the release lever to the Loading Paper section for additional information. • Do not fill above the max line. 8. Load paper into the WorkCentre. Secure the paper tray...
... that the alternate paper tray is always open before opening the front cover. 12.Press the front cover release buttons to be needed if the WorkCentre has to open the side cover. 10.Remove the Caution tape from the cover. 11.Remove the two red.... They will occur if the fuser pins are not removed. Note: Ensure that the side cover is lowered (XD 104/ 130df/ 155df only). 9. Press the release lever to the Loading Paper section for additional information. • Do not fill above the max line. 8. Load paper into the WorkCentre. Secure the paper tray...
User Guide
Page 44
...Scratches or smudges will flash in smudged copies. 2. - Follow the steps below . Remove the misfed paper. 5. Press the release lever to the Fuser Area. 6. Unfused toner may occur in the areas shown below to locate and clear the misfeed. Carefully remove the misfed paper in poor copy quality...on the copier diagram, and an E2 status code will result in the direction shown. Steps 3 - 5 for XD120f/130df/155df only 3. If paper cannot be removed, skip to open the side cover. Fuser Area Exit Area Paper Feed Area 36 Paper Feed Area Note: Ensure that the alternate paper tray is...
...Scratches or smudges will flash in smudged copies. 2. - Follow the steps below . Remove the misfed paper. 5. Press the release lever to the Fuser Area. 6. Unfused toner may occur in the areas shown below to locate and clear the misfeed. Carefully remove the misfed paper in poor copy quality...on the copier diagram, and an E2 status code will result in the direction shown. Steps 3 - 5 for XD120f/130df/155df only 3. If paper cannot be removed, skip to open the side cover. Fuser Area Exit Area Paper Feed Area 36 Paper Feed Area Note: Ensure that the alternate paper tray is...
User Guide
Page 45
...to the Exit Area. paper is hot. E2 Clearing the Paper Path (continued) Fuser Area Warning: The fuser area is not seen in this area skip to open the side cover. 2. Take care when removing paper from the fuser area. Note: Ensure that the alternate paper tray is lowered (XD104 105f/ 130df.../ 155df only). 1. Pull down on the fuser lever. • This will release pressure on the fuser lever. 5. Unfused toner may adhere in the area, resulting in the direction shown. 4. Caution: Do not pull paper up on the paper. ...
...to the Exit Area. paper is hot. E2 Clearing the Paper Path (continued) Fuser Area Warning: The fuser area is not seen in this area skip to open the side cover. 2. Take care when removing paper from the fuser area. Note: Ensure that the alternate paper tray is lowered (XD104 105f/ 130df.../ 155df only). 1. Pull down on the fuser lever. • This will release pressure on the fuser lever. 5. Unfused toner may adhere in the area, resulting in the direction shown. 4. Caution: Do not pull paper up on the paper. ...
User Guide
Page 46
Pull down on the fuser lever. • This will release pressure on the fuser lever. 7. Gently pull the paper out through the exit area. 6. Press the front cover release buttons to open the front cover. 3. Press the release lever to 1 open the side cover. 2. Close the front cover and side cover. 38 - E2 Clearing the Paper Path (continued) Exit Area 2 Note: Ensure that the alternate paper tray is lowered (XD104/105f/130df/155df only). 1. Turn the knob in the direction of the arrow to move the paper to the exit area. 5. Push up on the paper. 4.
Pull down on the fuser lever. • This will release pressure on the fuser lever. 7. Gently pull the paper out through the exit area. 6. Press the front cover release buttons to open the front cover. 3. Press the release lever to 1 open the side cover. 2. Close the front cover and side cover. 38 - E2 Clearing the Paper Path (continued) Exit Area 2 Note: Ensure that the alternate paper tray is lowered (XD104/105f/130df/155df only). 1. Turn the knob in the direction of the arrow to move the paper to the exit area. 5. Push up on the paper. 4.