Troy-Bilt Big Red Support and Manuals
Get Help and Manuals for this Troy-Bilt item
View All Support Options Below
Free Troy-Bilt Big Red manuals!
Problems with Troy-Bilt Big Red?
Ask a Question
Free Troy-Bilt Big Red manuals!
Problems with Troy-Bilt Big Red?
Ask a Question
Most Recent Troy-Bilt Big Red Questions
Tillers Main Harness Connection
I can't find neutral safety switch to attach the main harness connection -figure 3-5.I am holding ha...
I can't find neutral safety switch to attach the main harness connection -figure 3-5.I am holding ha...
(Posted by emangian 8 years ago)
Popular Troy-Bilt Big Red Manual Pages
Operation Manual - Page 1
... TO OPERATE THIS MACHINE. BOX 361131 CLEVELAND, OHIO 44136-0019
Form No. 769-08675 (November 16, 2012) FAILURE TO COMPLY WITH THESE INSTRUCTIONS MAY RESULT IN PERSONAL INJURY. Printed In USA
TROY-BILT LLC, P.O. Safe Operation Practices • Set-Up • Operation • Maintenance • Service • Troubleshooting • Warranty
Operator's Manual
Rear-Tine Tiller -
Operation Manual - Page 2
... available at the rear of printing. Review this machine, you can locate the model plate by standing at the operator's position and looking down at the time of the deck.
You can seek help from the experts. Model Number Serial Number
Customer Support
Please do so could result in this manual is responsible for purchasing a Troy-Bilt Garden Tiller. Choose from...
Operation Manual - Page 4
... use a nozzle lock-open flame, spark or pilot light as necessary.
7. Keep machine, attachments and accessories in safe working order.
2. f. Do not touch.
15. If the machine should start making any damage. Before cleaning, repairing, or inspecting, stop the engine and make certain the tines and all clutch levers (if fitted) and stop before storing. c. h. Never...
Operation Manual - Page 7
...; The following parts (electric start the engine until instructed to prop machine
Contents of two height settings and tighten the...Troy-Bilt Technical Service Department if any of Carton
• One Tiller • One Hardware Pack • One Engine Operator's Manual
• One Handlebar Support • One Wheels/Tines PTO Lever
• One Handlebar Assembly • One Operator's Manual...
Operation Manual - Page 12
... 3- Never bring a gas can
Service the engine with gasoline and oil as instructed in each tire to equal air
...an explosion of ignition. and secure with your tiller.
See Figure 3-14. Never fuel the machine indoors or while the engine is extremely flammable and...from pulling to one end attached to check the oil level at the factory. Assembly & Set-Up
To Avoid Personal Injury...
Operation Manual - Page 44
... site at its option, repair or replace, free of any part, accessory or attachment not approved by Troy-Bilt for use with the product(s) covered by MTD Products Limited with your product. d. f. g.
No other express warranty, whether written or oral, except as set forth above , given by someone other than the amount of the purchase price of other peril or...
Technical Manual - Page 3
... Manual contains additional service and maintenance information that could get caught in moving parts when the engine is running or still hot. Refer to "Quick Reference Repair Index" in this section for the PTO HORSE Model TROY-BILT® Roto Tiller-Power Composter built by disconnecting the spark plug wire and keeping the wire away from moving parts of the tiller...
Technical Manual - Page 4
... use care to touch a terminal that is grounded.
Quick Reference Repair Index
To obtain service information for the following topics, please refer to sharp, knife-like edges. Ventilate when charging or using in a U.L. HANDLE PARTS CAREFULLY! Use only genuine Troy-Bilt replacement parts. approved covered metal safety container to prevent fire from a short circuit could present...
Technical Manual - Page 5
... the engine throttle control in the OFF position and shift the Wheels/Tines/PTO Drive Lever into reverse.
See the Owner/Operator Manual for instructions.
• Install a new clutch pawl spring at TOLL-FREE 1-800-833-6990. call the TROY-BILT' Tiller Technical Service Department at the end of the reverse disc and/or reverse spring and plunger...
Technical Manual - Page 9
... oil to seep out between the seal and the housing. Contact the TROY-BILT Technical Service Department for sand holes (imperfections in the cast iron) or cracks in the tiller tine shaft.
If the leak is on an undamaged part of the shaft. ■ Replace the wheel shaft if necessary.
• Determine if the seal fits loosely...
Technical Manual - Page 15
...bars halfway. Set the yoke in the necessary 15
position and install the bolt, bushings, and washers (4) that the Tines/PTO Clutch Lever (13) is covered with one...the tiller attachment. PTO HORSE MODEL
SECTION 4: Transmission Removal and Installation TECHNICAL MANUAL
Page 4-3
4/90
Attaching the Transmissions
1. Tighten the bolts. Install the handlebar mounting base and the attached ...
Technical Manual - Page 19
... the shaft and can perform these instructions. Removal 1. Observe the part of the housing, the bearing cup (20), or the retaining ring (21).
15. If it is excessively worn or damaged, or if the customer has had difficulty engaging the tiller attachment, replace the part with a newer-style socket head screw that engages the dog clutch (5). Remove the...
Technical Manual - Page 28
PTO HORSE MODEL
TECHNICAL MANUAL
Page 6-1
4/90
SECTION 6: Tiller Attachment Transmission
This section describes the the procedures for parts ordering information.
A WARNING: When servicing the machine, prevent unintentional starting of the worm). Note: Either of two basic types of drive shafts may have been installed at either end of the engine by blue welds at the factory: an ...
Technical Manual - Page 30
... past the groove. PTO HORSE MODEL
TECHNICAL MANUAL
Page 6-3
4/90
SECTION 6: Tiller Attachment Transmission
tion has not been maintained; Make sure the beveled cup is towards the front of the snap ring is scored or excessively worn, dirt may have gotten inside the transmission. Although not easy to remove, inspect, and install the tiller attachment's tine shaft assembly. Using...
Technical Manual - Page 34
... MANUAL
Page 7.1
4/90
SECTION 7: Special Repairs and Procedures
Installing a New Tines/PTO /Clutch Lever Assembly
In early model PTO Horse models, a ball bearing assembly on the Tines/PTO Clutch Shaft functioned as the contact piece that holds the clutch lever knob (2) to the clutch lever (3). The Part Number 10353 service kit contains all the way. Separate the tiller tine attachment...
Troy-Bilt Big Red Reviews
We have not received any reviews for Troy-Bilt yet.