TP-Link T1600G-28PS Support and Manuals
Get Help and Manuals for this TP-Link item
View All Support Options Below
Free TP-Link T1600G-28PS manuals!
Problems with TP-Link T1600G-28PS?
Ask a Question
Free TP-Link T1600G-28PS manuals!
Problems with TP-Link T1600G-28PS?
Ask a Question
TP-Link T1600G-28PS Videos
???????? ????? 24 ????? PoE Switch ?????????? TP-Link T1600G-28PS By OKD Network
Duration: 10:11
Total Views: 3,056
Duration: 10:11
Total Views: 3,056
Popular TP-Link T1600G-28PS Manual Pages
802.1X Client Software User Guide - Page 4
...; 64-bit Windows 8.1
1 When using the TP-Link switch as this user guide to acquire information about the installation and configuration of the 802.1X Client Software.
1 Installation
1. Authentication Server System: The authentication server system is usually an 802.1X-supported network device, such as the authenticator system, please read this TP-Link switch. It provides the physical or...
T1600G-28PSUN V3 CLI Reference Guide Guide - Page 48
... System information and System IP, reboot and reset the switch, upgrade the switch system and other operations.
4.1 system-time manual
Description
The system-time manual command is used to an NTP Server.
Example
Configure the system mode as manual, and the time is 12/20/2010 17:30:35 T1600G-28TS(config)# system-time manual 12/20/2010-17...
T1600G-28PSUN V3 CLI Reference Guide Guide - Page 65
... firmware upgrade ip-address ip-addr filename name
Parameter ip-addr -- Specify the name for example 192.168.0.1 or fe80::1234. Example
Upgrade the switch's backup iamge file with the file firmware.bin in the TFTP server with this firmware: T1600G-28TS# firmware upgrade ip-address 192.168.0.148 filename firmware.bin
It will the Backup Image.
Both IPv4 and IPv6 addresses are
supported...
Jetstream Smart Switch Installation Guide - Page 19
... instructions to be purchased additionally. It needs to complete the Quick Setup. Follow the steps below.
1.
For more details, refer to log in . Enter your TP-Link ID will appear.
4. Enter the username and password you have configured this in the address bar. Via Omada Hardware Controller (OC200/OC300)
Omada Hardware Controller (OC200/OC300), which is pre-installed...
Jetstream Smart Switches User Guide - Page 13
... Using the CLI...427
Configuring DHCP Service
DHCP...431 Overview...431 Supported Features...431
DHCP Server Configuration...436 Using the GUI...436 Enabling DHCP Server...436 Configuring DHCP Server Pool...438 Configuring Manual Binding...439 Using the CLI...440 Enabling DHCP Server...440 Configuring DHCP Server Pool...443 Configuring Manual Binding...446
DHCP Relay Configuration...449 Using the...
Jetstream Smart Switches User Guide - Page 62
... right to load the following page. Retype the password.
3.1.2 Configuring Enable Password
Choose the menu SECURITY > AAA > Global Config to edit or modify. It contains 16 characters at most of the settings of different functions. Select the access level. No spaces are allowed. Figure 3-3 Configure Enable Password
User Guide 37 Specify a username for the account. Power User...
Jetstream Smart Switches User Guide - Page 64
... the settings of the current users.
User Guide 39 Step 3 Step 4 Step 5
Use the following command to privileged EXEC mode.
No spaces are allowed. It contains 16 characters at most, composed of different functions. By default, the encryption type is Admin. password: Enter a password for users' login.
After the encrypted password is saved to the configuration file...
Jetstream Smart Switches User Guide - Page 80
... set a profile with the desired parameters and bind the profile to the corresponding ports to quickly configure the PoE parameters. You can configure the PoE parameters one by one via configuring the PoE parameters manually. User Guide 55 Managing System
PoE Configurations (Only for Certain Devices)
6 PoE Configurations (Only for Certain Devices)
Note:
Only T1600G-52PS and TL-SG2428P support...
Jetstream Smart Switches User Guide - Page 324
... sends BPDUs. It also receives the other switches. In TP-Link switches, the port status includes: Blocking, Learning, Forwarding and Disconnected.
■■ Blocking In this BPDU, the root path cost wll be manually configured on each port.
The smaller the value, the higher link speed the port has. The path cost can be increased...
Jetstream Smart Switches User Guide - Page 434
... By default, it is enabled on the specified Layer 3 interface. Configure the IPv6 link-local address for the specified interface:
Manually configure the ipv6 link-local address for the specified interface: ipv6 address autoconfig
User Guide 409 Automatically configure the ipv6 link-local address for the specified interface: ipv6 address ipv6-addr link-local ipv6-addr: Specify the link-local...
Jetstream Smart Switches User Guide - Page 481
... port | ten-gigabitEthernet port } Enter Interface Configuration Mode. no switchport Switch the port channel to Privileged EXEC Mode. Configuring DHCP Service
DHCP Relay Configuration
Switch(config-if)#end Switch#copy running -config startup-config Save the settings in the configuration file. port-channel: Specify the port channel. ip helper-address ip-addr Specify DHCP server for example...
Jetstream Smart Switches User Guide - Page 483
port-channel: Specify the port channel. ip dhcp relay default-interface Set the interface as the default relay-agent interface.
show ip dhcp relay Verify the configuration of the DHCP server. User Guide 458 no switchport Switch the port channel to fill in the Relay Agent IP Address field of DHCP packets from 1 to Privileged EXEC Mode. no switchport Switch...
Jetstream Smart Switches User Guide - Page 511
... about how to set its DHCP configuration file. Configure the interface address of the configurations are as follows:
1) Configuring Switch A
a. Configuring DHCP Service
Figure 5-28 Network Topology for the DHCP server you can assign IP addresses of different address pools to the computers in different groups. Configure 802.1Q VLAN. For details, refer to configure DHCP Interface Relay...
Jetstream Smart Switches User Guide - Page 553
...-config Save the settings in the configuration file. User Guide 528
show qos ...default, the 802.1p priority 0 to 802.1p priority mapping for the desired port. show qos trust interface [fastEthernet port | gigabitEthernet port | ten-gigabitEthernet port | port-channel port-channel-id] Verify the trust mode of the TC queue. Configuring QoS
Class of Service Configuration...
Jetstream Smart Switches User Guide - Page 899
... Save the settings in IPv4 or IPv6. v1 | v2c | v3: Choose the security model used by...Guide 874 Configuring SNMP & RMON
Notification Configurations
Step 2
Step 3 Step 4 Step 5
snmp-server host ip udp-port user-name [smode { v1 | v2c | v3 }] [slev {noAuthNoPriv | authNoPriv | authPriv }] [type { trap | inform}] [retries retries] [timeout timeout] Configure parameters of the host. The default...
TP-Link T1600G-28PS Reviews
We have not received any reviews for TP-Link yet.