TP-Link T1600G-52TSTL-SG2452 Support and Manuals
Get Help and Manuals for this TP-Link item
View All Support Options Below
Free TP-Link T1600G-52TSTL-SG2452 manuals!
Problems with TP-Link T1600G-52TSTL-SG2452?
Ask a Question
Free TP-Link T1600G-52TSTL-SG2452 manuals!
Problems with TP-Link T1600G-52TSTL-SG2452?
Ask a Question
Popular TP-Link T1600G-52TSTL-SG2452 Manual Pages
T1600G-28TS V1 User Guide - Page 13
...to solve mainly authentication and security problems.
Chapter 14 SNMP
This module ...specified VLAN so as to provide different quality of service for the switch to the network. Here mainly... to a port/VLAN to take its effect on a specific port/VLAN. Chapter 12 ACL
This module is used to...introduces:
• SNMP Config: Configure global settings of SNMP function.
• Notification: Configure...
T1600G-28TS V1 User Guide - Page 15
... setting back to factory
default settings. 10/100/1000Mbps Ports: Designed to connect to the device with high security. Examples include powering network cameras, wireless LAN access points, IP telephones, network hubs, embedded computers etc.
2.2 Appearance Description
2.2.1 Front Panel
The front panel of T1600G-28TS The following parts are located on the switch support...
T1600G-28TS V1 User Guide - Page 16
...switch works properly
SYS
On/Off
The switch works improperly
7 T1600G-52TS features 4 individual SFP ports and supports 1000M SFP module connection only.
LEDs
Name
Status...reset the software setting back to factory default settings.
10/100/1000Mbps Ports: Designed to connect to install the SFP module. Figure 2-2 Front Panel of T1600G-52TS
The following parts are located ...
T1600G-28TS V1 User Guide - Page 153
Specify interface administrator status.
Working status is up when admin status is enabled, line protocol is up and IP Address is set.
Display IP address allocation mode. None : without ip. Static: setup manually. DHCP: allocated through DHCP. BOOTP: allocated through BOOTP.
Click Edit to disable the interface's Layer 3 capabilities. Displays...
T1600G-28TS V1 User Guide - Page 155
...should be sent next.
The smaller the distance is, the higher the priority is set. De stination/Mask: Next Hop: Distance :
Displays the destination and subnet of the... the route. Displays the IP address allocation mode. None: without ip. Static: setup manually. DHCP: allocated through DHCP. BOOTP: allocated through BOOTP. Figure 9-2 Routing Table ...
T1600G-28TS V1 User Guide - Page 158
...10 QoS
QoS (Quality of Service) functions to provide different quality of service for resources must be mapped to the egress queues according to the CoS of queue scheduling. The switch supports four schedule modes: SP, ... on port, on 802.1P and on port is congested, the problem that many packets
compete for various network applications and requirements and optimize the bandwidth resource distribution so...
T1600G-28TS V1 User Guide - Page 203
... to users so as to their accounts and passwords. The bound entry can contain 255 sub-options...get proper IP addresses. The Remote ID is manually configured by the user by discarding the DHCP... the Host for automatic binding. This switch supports two sub-options: Circuit ID and Remote ID... in the network, network confusion and security problem will happen. DHCP Snooping is no universal ...
T1600G-28TS V1 User Guide - Page 216
.... The authenticator system in trouble, the alternate authentication server ...Extensible Authentication Protocol) to the instructions (accept or reject) received ...support the 802.1X authentication protocol.
(2) Authenticator System: The authenticator system is an entity that provides authentication service...an 802.1X authentication through PAP (Password Authentication Protocol) or CHAP (Challenge ...
T1600G-28TS V1 User Guide - Page 236
...between management station and managed agent.
RMON Group
This switch supports the following four RMON Groups defined on the RMON standard (RFC1757): History Group...set to monitor the statistic of a monitored variable exceeds the threshold, an alarm event is generated, which is configured to apply.
14.3 RMON
RMON (Remote Monitoring) based on the specific ports.
Use r: Security Model...
T1600G-28TS V1 User Guide - Page 245
... LLDP optional TLVs are the result of auto-negotiation during link initiation or of manual set override action. TLV Type
De scription
Port Description TLV
The Port Description TLV allows...should include the full name and version identification of the system and whether or not these settings are supported. c)Whether these primary functions are enabled. Power Via MDI TLV
The Power Via MDI ...
T1600G-28TS V1 User Guide - Page 252
...configure the LLDP-MED parameters of the TLVs in the Inventory Management set is intended to . If support for all Inventory Management TLVs shall be transmitted based on this ...Revision TLV, Firmware Revision TLV, Software Revision TLV, Serial Number TLV, Manufacturer Name TLV, Model Name TLV and Asset ID TLV.
Inv e ntory TLV
The Inventory TLV set of specific applications on configuration...
T1600G-28TS V1 User Guide - Page 267
Differentiated Services Code Point (DSCP) DSCP uses a six-bit tag to provide for flow control on the Bootstrap... 64 different forwarding behaviors. Domain Name Service (DNS) A system used to provide bootup information for different kinds of forwarding. DHCP is supported by prioritizing packets based on network policies, different kinds of traffic can be set according to the port default, the ...
T1600G-52TS V1 CLI Reference Guide - Page 77
...for Hawaii.
65 UTC-10:00 -- Set the date and time manually, MM/DD/YYYY-HH:MM:SS
... manual, and the time is 12/20/2010 17:30:35
T1600G-52TS(config)# system-time manual...upgrade the switch system and other operations.
11.1 system-time manual
Description
The system-time manual command is used to configure the system time manually. TimeZone for the NTP Server. Syntax
system-time manual...
T1600G-52TS V1 CLI Reference Guide - Page 82
... name information, please use no hostname command.
Syntax
hostname [ hostname ] no location
Parameter
location -- Command Mode
Global Configuration Mode
Example
Configure the system name as TPLINK: T1600G-52TS(config)# hostname TPLINK
11.7 location
Description
The location command is "SHENZHEN" by default.
70
It consists of Oct and the offset is 45 minutes...
T1600G-52TS V1 CLI Reference Guide - Page 89
... IPv6 addresses are supported, for the firmware file. Command Mode
Privileged EXEC Mode
Example
Upgrade the switch's backup iamge file with the file firmware.bin in the TFTP server with the IP address fe80::1234, but do not reboot the switch: T1600G-52TS# firmware upgrade ip-address fe80::1234 filename firmware.bin It will only upgrade the backup image...
TP-Link T1600G-52TSTL-SG2452 Reviews
We have not received any reviews for TP-Link yet.