Operation Manual
Page 11
... up through -sawing operations. TO LOCK YOUR SAW: Press the switch down to prevent unauthorized and possible hazardous use by an insert called the throat plate. To accommodate wide panels, the saw is set with a handwheel on the front of the cabinet. The rip fence is intended to turn OFF ( O ). SWITCH...
... up through -sawing operations. TO LOCK YOUR SAW: Press the switch down to prevent unauthorized and possible hazardous use by an insert called the throat plate. To accommodate wide panels, the saw is set with a handwheel on the front of the cabinet. The rip fence is intended to turn OFF ( O ). SWITCH...
Operation Manual
Page 17
...adjusting handwheel. Using a flathead screwdriver, turn the screw counterclockwise to secure in place. HANDLE SCREW WASHER NYLON HEIGHT/BEVEL NUT ADJUSTING HANDWHEEL THROAT PLATE Fig. 9 Fig. 11 Fig. 10 17 - ASSEMBLY TO INSTALL THE HANDLE See Figure 9. Hold the nylon nut securely and .../bevel adjusting handwheel counterclockwise. To remove the throat plate, place your index finger in the hole and lift the front end pulling the throat plate out toward the front of the saw. To reinstall the throat plate, slip the tab into the hole on the back ...
...adjusting handwheel. Using a flathead screwdriver, turn the screw counterclockwise to secure in place. HANDLE SCREW WASHER NYLON HEIGHT/BEVEL NUT ADJUSTING HANDWHEEL THROAT PLATE Fig. 9 Fig. 11 Fig. 10 17 - ASSEMBLY TO INSTALL THE HANDLE See Figure 9. Hold the nylon nut securely and .../bevel adjusting handwheel counterclockwise. To remove the throat plate, place your index finger in the hole and lift the front end pulling the throat plate out toward the front of the saw. To reinstall the throat plate, slip the tab into the hole on the back ...
Operation Manual
Page 18
... are engaged and the riving knife is above the saw blade. Lock the release lever by pushing the lever down . Reinstall the throat plate. RELEASE LEVER (UNLOCKED) IN "UP" POSITION FOR THROUGH CUTTING RELEASE LEVER (LOCKED) IN "DOWN" POSITION FOR NON-THROUGH CUTTING Fig. 11 18 -...and the riving knife is below the saw blade. Pull the riving knife up " position for non-through cutting: Remove the throat plate. Raise the saw blade by turning the height/bevel adjusting handwheel clockwise. Unlock the release lever by pulling it up. ...
... are engaged and the riving knife is above the saw blade. Lock the release lever by pushing the lever down . Reinstall the throat plate. RELEASE LEVER (UNLOCKED) IN "UP" POSITION FOR THROUGH CUTTING RELEASE LEVER (LOCKED) IN "DOWN" POSITION FOR NON-THROUGH CUTTING Fig. 11 18 -...and the riving knife is below the saw blade. Pull the riving knife up " position for non-through cutting: Remove the throat plate. Raise the saw blade by turning the height/bevel adjusting handwheel clockwise. Unlock the release lever by pulling it up. ...
Operation Manual
Page 19
...increasing the risk of the riving knife. To install blade guard: Lift the guard lever up " position. Reinstall the throat plate. BLADE GUARD Fig. 12 GUARD LEVER WARNING: Replace dull or damaged anti-kickback pawls. ASSEMBLY TO CHECK SAW BLADE INSTALLATION See Figure 12.... Do not overtighten. Reinstall the throat plate. Check all clearances for clearances and free movement. English Fig. 13 To tighten the blade: Using the open end ...
...increasing the risk of the riving knife. To install blade guard: Lift the guard lever up " position. Reinstall the throat plate. BLADE GUARD Fig. 12 GUARD LEVER WARNING: Replace dull or damaged anti-kickback pawls. ASSEMBLY TO CHECK SAW BLADE INSTALLATION See Figure 12.... Do not overtighten. Reinstall the throat plate. Check all clearances for clearances and free movement. English Fig. 13 To tighten the blade: Using the open end ...
Operation Manual
Page 22
... the Electrical section in . Inspect the work Forcing a cut Not following correct operating procedures Misusing the saw , blade guard, under the throat plate, and any loose knots with the blade. Use of kickback. 22 -
... the Electrical section in . Inspect the work Forcing a cut Not following correct operating procedures Misusing the saw , blade guard, under the throat plate, and any loose knots with the blade. Use of kickback. 22 -
Operation Manual
Page 35
... knife. Unplug the saw. Remove the blade guard and anti-kickback pawls. Lower the saw blade and reinstall the throat plate. Check all items are needed. Be sure the dome side of the saw . ADJUSTMENTS WARNING: Before performing any adjustments until you have ...43 RIVING KNIFE BLADE 35 - Do not start any adjustment, make sure it turns freely. Lower the saw blade and remove the throat plate. Make sure the bevel locking lever is securely tightened. Holding both wrenches firmly, pull the closed end blade wrench over the arbor ...
... knife. Unplug the saw. Remove the blade guard and anti-kickback pawls. Lower the saw blade and reinstall the throat plate. Check all items are needed. Be sure the dome side of the saw . ADJUSTMENTS WARNING: Before performing any adjustments until you have ...43 RIVING KNIFE BLADE 35 - Do not start any adjustment, make sure it turns freely. Lower the saw blade and remove the throat plate. Make sure the bevel locking lever is securely tightened. Holding both wrenches firmly, pull the closed end blade wrench over the arbor ...
Operation Manual
Page 37
... rails, periodically apply paste wax to them and buff to comply with a sufficient amount of high grade lubricant for tightness and condition. Make sure the throat plate is in good condition and in contact with a soft damp cloth. English WARNING: Do not at any maintenance, make sure the tool is in the...
... rails, periodically apply paste wax to them and buff to comply with a sufficient amount of high grade lubricant for tightness and condition. Make sure the throat plate is in good condition and in contact with a soft damp cloth. English WARNING: Do not at any maintenance, make sure the tool is in the...
Parts Diagram
Page 3
NUMBER DESCRIPTION QTY 1 089037007713 Throat Plate Assembly 1 2 089015001001 Screw (M8 x 30 mm 1 3 089015001013 Screw (M8 x 35 mm 1 4 089037007004 Nut (M8 2 5 410102702 ...mm 1 34 080015001439 Middle Bracket 1 35 089037007019 Lever 1 36 089037007020 Clamp Lock 1 37 089037007021 Clamp 1 38 089037007097 Pad 1 39 089037007098 Plate Support 1 40 412011007 Washer (D5 x D12 x 1.5t 2 41 412021005 Washer (D5 2 42 089037007101 Screw (M5 x 10 mm, ...PARTS LIST FOR FIGURE A KEY PART KEY PART NO. RYOBI 10 in.
NUMBER DESCRIPTION QTY 1 089037007713 Throat Plate Assembly 1 2 089015001001 Screw (M8 x 30 mm 1 3 089015001013 Screw (M8 x 35 mm 1 4 089037007004 Nut (M8 2 5 410102702 ...mm 1 34 080015001439 Middle Bracket 1 35 089037007019 Lever 1 36 089037007020 Clamp Lock 1 37 089037007021 Clamp 1 38 089037007097 Pad 1 39 089037007098 Plate Support 1 40 412011007 Washer (D5 x D12 x 1.5t 2 41 412021005 Washer (D5 2 42 089037007101 Screw (M5 x 10 mm, ...PARTS LIST FOR FIGURE A KEY PART KEY PART NO. RYOBI 10 in.
Parts Diagram 1
Page 3
MODEL NUMBER RTS10G The model number will be found on a label attached to the cabinet. Left 1 3 NUMBER DESCRIPTION QTY 1 089040002704 Throat Plate Assembly 1 2 089015001001 Screw (M8 x 30 mm 1 3 089015001013 Screw (M8 x 35 mm 1 4 089037007004 Nut (M8 2 5 410102702 Screw (1/4-20 x 7/8 in, Flat Hd 4 6 089037007005 Table 1 7 089037007006 ...PARTS LIST FOR FIGURE A KEY PART KEY PART NO. Right 1 56 089037007910 Blade Guard Warning Label - TABLE SAW - NUMBER DESCRIPTION QTY NO. RYOBI 10 in. TABLE SAW or when ordering parts.
MODEL NUMBER RTS10G The model number will be found on a label attached to the cabinet. Left 1 3 NUMBER DESCRIPTION QTY 1 089040002704 Throat Plate Assembly 1 2 089015001001 Screw (M8 x 30 mm 1 3 089015001013 Screw (M8 x 35 mm 1 4 089037007004 Nut (M8 2 5 410102702 Screw (1/4-20 x 7/8 in, Flat Hd 4 6 089037007005 Table 1 7 089037007006 ...PARTS LIST FOR FIGURE A KEY PART KEY PART NO. Right 1 56 089037007910 Blade Guard Warning Label - TABLE SAW - NUMBER DESCRIPTION QTY NO. RYOBI 10 in. TABLE SAW or when ordering parts.