Ryobi TS1343L Support and Manuals
Get Help and Manuals for this Ryobi item
View All Support Options Below
Free Ryobi TS1343L manuals!
Problems with Ryobi TS1343L?
Ask a Question
Free Ryobi TS1343L manuals!
Problems with Ryobi TS1343L?
Ask a Question
Most Recent Ryobi TS1343L Questions
Vacuum Adaptor
How do I attach my Ryobi TS1343L saw to my shop vac. The end of my vac hose has a 1.25" male fitting...
How do I attach my Ryobi TS1343L saw to my shop vac. The end of my vac hose has a 1.25" male fitting...
(Posted by frankso1234shop 11 years ago)
Where Is The Switch Lock On The Ryobi Ts1343l Miter Saw?
(Posted by drmimiky 11 years ago)
Can't Find 'miter Lock Plate'.
New to power tools, so this is probably a rookie question: Just bought a Ryobi TS1343L, only problem...
New to power tools, so this is probably a rookie question: Just bought a Ryobi TS1343L, only problem...
(Posted by adam56194 11 years ago)
Even Set To 0, My Cuts Are Not Straight, Blade Is New. How Can I Fix This?
(Posted by djsmooth1964 12 years ago)
Popular Ryobi TS1343L Manual Pages
Operation Manual - Page 1
...miter saw has been engineered and manufactured to our high standard for your purchase. When properly cared for, it will give you for dependability, ease of operation, and operator safety. SAVE THIS MANUAL FOR FUTURE REFERENCE
Thank you years of injury, the user must read and understand the operator's manual before using
this product.
OPERATOR'S MANUAL
10 in. Compound Miter Saw
TS1343L...
Operation Manual - Page 8
....
Push Blocks (for narrow ripping operations. Ripping or Rip Cut A cutting operation along the length of a workpiece usually caused by a fence, miter gauge, or other than 90° to the blade other than the blade, which the operation is not properly supported. Snipe (planers) Depression made with the blade.
Push Blocks (for table saws) Device used to stop the workpiece...
Operation Manual - Page 9
... Capacity with Miter at 45°/Bevel 45°: Maximum nominal lumber sizes 2 x 4
UPPER BLADE GUARD
"D" HANDLE/ CARRYING HANDLE
DUST BAG
BLADE WRENCH
BEVEL LOCK KNOB
MITER FENCE
MITER TABLE
BASE
SWITCH TRIGGER
LOWER BLADE GUARD
THROAT PLATE
"NO HANDS ZONE" BOUNDARY LINE
"NO HANDS ZONE" LABEL
MITER SCALE
WORK CLAMP
9
CONTROL ARM
MITER LOCK HANDLE
Fig. 1
Blade Diameter 10 in .
Operation Manual - Page 10
...
KNOW YOUR COMPOUND MITER SAW
See Figure 1. blade is packed with sufficient power to handle tough cutting jobs.
A blade wrench is included with your miter saw 's base.
The safe use of servicing.
10 in the saw . Before use of this product requires an understanding of the information on each side of the project you are for ease of this operator's manual as...
Operation Manual - Page 11
... of the compound miter saw, disconnect it from rotating. diameter may be used. SPINDLE LOCK BUTTON
See Figure 3. Depress and hold the lock button while installing, changing, or removing blade. When the lock is installed and locked, the switch is made of shock-resistant, seethrough plastic that provides protection from each side of the miter table.
SWITCH TRIGGER...
Operation Manual - Page 13
..., sliding, or walking is factory set for this tool until the parts are not assembled to make sure that may have been improperly assembled could result to a work surface.
Bolts should be of sufficient length to make sure the compound miter saw is not secured to the blade if it strikes the miter fence during shipping.
Do...
Operation Manual - Page 14
...
miter table base. Rotate the knob on the miter saw blade. To install the work clamp: Place the shaft of the work clamp to move it may interfere with the blade guard prior to beginning any cutting operation to reduce the risk of the work clamp provides greater control by clamping the workpiece to the fence or the miter table...
Operation Manual - Page 16
... replace blade bolt. CAUTION:
Always install the blade with the flats on the upper blade guard.
Tighten blade bolt securely. Replace the lower blade guard and blade bolt cover. Replace blade bolt cover screw and tighten securely. NOTE: The blade bolt has left -hand threads.
Never use a blade that is too thick to allow laser guide washer to expose the blade...
Operation Manual - Page 17
... of the compound miter saw without all guards securely in place and in the miter table. Never engage spindle lock button when blade is not engaged before reconnecting saw arm to its full raised position.
Loosen the miter lock handle approximately one leg of the square beside the throat plate in good operating condition.
SQUARING THE MITER TABLE TO THE FENCE
See...
Operation Manual - Page 20
... cutting plastic, use any cutting operation freehand (without holding workpiece against the fence). Miter cross cuts are made with the miter table set at some angle other than zero. Pull out the lock pin and lift saw is running and the blade is made by the manufacturer of the accessory blades available from the Ryobi dealer. from binding in...
Operation Manual - Page 22
... handle.
NOTE: You can be set from miter table. A compound miter cut made .
Grasp the saw , perform a dry run of miter and bevel settings are interdependent with thumb then squeeze the switch trigger. OPERATION
Grasp the stock firmly with one hand and secure it against the fence. Each time you adjust the miter setting you change the effect of the...
Operation Manual - Page 23
... operation.
Allow several seconds for the blade to reach maximum speed.
Slowly lower the blade into and through the workpiece.
Release the switch trigger and allow the saw and work clamp or a C-clamp to stop rotating before removing the workpiece from miter table.
The support should be placed along the workpiece so it against the fence...
Operation Manual - Page 25
... order to set. See the chart below for cutting All Standard (U.S.) crown molding with 52° and 38° angles. LAYING MOLDING FLAT ON THE MITER TABLE
See Figure 32. OPERATION
CUTTING CROWN MOLDING
The compound miter saw .
52° 38°
CEILING
W
A
L
L
FENCE
INSIDE CORNER
TOP EDGE AGAINST FENCE = LEFT SIDE, INSIDE CORNER RIGHT SIDE, OUTSIDE CORNER
MITER TABLE
FENCE
OUTSIDE...
Operation Manual - Page 27
...the components might have saw repaired at your nearest RYOBI AUTHORIZED SERVICE CENTER. Also, over a period of the saw blade to the miter table at the factory and normally do not require readjustment. Damage could result in the pivot joints, have been jarred out of alignment during operation of the saw. BEVEL PIVOT ADJUSTMENT
The compound miter saw should never need adjustments...
Operation Manual - Page 30
... tool, should a need ever exist for repair parts or service, simply contact your nearest Authorized Service Center. Please call or visit. AND SERIAL NO.
Compound Miter Saw
TS1343L - You can also check our web site at www.ryobitools.com for your exposure to the motor housing.
Some examples of Authorized Service Centers.
• MODEL NO. Your risk from chemically-treated...
Ryobi TS1343L Reviews
We have not received any reviews for Ryobi yet.