Ryobi RTS30 Support and Manuals
Get Help and Manuals for this Ryobi item
Most Recent Ryobi RTS30 Questions
Do You Have A Manual For Ryobi 12t?
(Posted by toronaga236 2 years ago)
What Wires Go To Switch And Reset On10 Inch Ryobi Table Saw
My saw stop working I took the cover off the svitch I notice the reset switch was not wired and ther...
My saw stop working I took the cover off the svitch I notice the reset switch was not wired and ther...
(Posted by Merle1954sm 9 years ago)
How To Replace The Bevel Lock Washer On A Ryobi Rts30
(Posted by mike1QWJani 9 years ago)
How To Reset After The Saw Overloads
(Posted by bhill18697 10 years ago)
Where Are The Positive Stops Inside The Cabinet? Need To Make Adjustments For
I need to make adjustments for a 90 degree cut.
I need to make adjustments for a 90 degree cut.
(Posted by rnicot 10 years ago)
Ryobi RTS30 Videos
ryobi rts30 table saw unboxing
Duration: 12:25
Total Views: 5,307
Duration: 12:25
Total Views: 5,307
Popular Ryobi RTS30 Manual Pages
English Manual - Page 5
...WARNING:
Some dust created by power sanding, sawing, grinding, drilling, and other construction activities contains chemicals known to support or guide the workpiece. Instructions for wide or long work before disconnecting it, to avoid accidental starting when reconnecting to instructions on how often you loan someone this manual or addendums. Use of accessories that are : •...
English Manual - Page 7
... you read thoroughly and understand completely the operator's manual. If you do not understand the warnings and instructions in the operator's manual, do not attempt to use this product until you return the product to the nearest AUTHORIZED SERVICE CENTER for repair.
When servicing, use this product. Call Ryobi customer service for use eye protection which , if not...
English Manual - Page 9
... arm and table saws) A devise which, when properly installed and maintained, is bent (or set) outward from the face of the blade. Cross Cut A cutting or shaping operation made with adjustable blades or knives.
A push stick (not a push block) should be or has been cut removing a wedge from a block so the end (or part of the end...
English Manual - Page 11
... this product, familiarize yourself with optional clamps and accessories.
RIP FENCE - BLADE - SPREADER -
carbidetipped blade.
Located on the front of the cabinet, locks the angle setting of the saw table. Located on the front rail, the easy-to lower and raise the blade for bevel angles. SCALE - FEATURES
KNOW YOUR TABLE SAW
See Figure 2. WARNING:
Do not use this...
English Manual - Page 12
... and the blade. The rip fence is intended to prevent unauthorized and possible hazardous use by an insert called the throat plate. TO TURN YOUR SAW OFF:
Press the switch down .
Remove the switch key from accidentally starting when power returns. With the miter fence removed, the miter table offers additional support for all...
English Manual - Page 15
... supply until you chose to remove the leg stand, the table saw must be of sufficient length to modify this tool or create accessories not recommended for use . NEVER operate the saw 's base for this warning could result in this manual. If any parts are damaged or missing do not operate this tool until the...
English Manual - Page 17
... SCREW THROAT
PLATE
Fig. 11 to Store the table saw Accessories
See Figures 8 - 9. ASSEMBLY
to remove/replace the THROAT PLATE
See Figure 11. Lower the blade by snapping each accessory in the saw table. Retighten the screws, being careful not to overtighten,
which can cause the throat plate to the desired location then either side of the saw cabinet) specifically designed...
English Manual - Page 34
... dado throat plate (part number 0134010313) is fully engaged and the arbor
extends at the base of the spreader. stack dado (up to lock the angle.
Lower the blade, insert the throat plate, then securely tighten the throat plate screw. Do not use with your hands when making any non-through cut
See Figure 45. NOTE: This saw blade. Mount the dado blade...
English Manual - Page 35
... throat plate screws. The table saw has been adjusted at 0˚ and 45˚. To avoid unnecessary set to be sure adjustments are snug against the arbor housing. TO REPLACe THE BLADE
See Figures 46 - 48. Unplug the saw.
Lower the saw blade and reinstall the throat plate. Holding both wrenches firmly, pull the larger wrench forward to check your setups...
English Manual - Page 42
Table Saw
BTS21
WARNING:
Some dust created by calling 1-800-525-2579. To reduce your model and serial number from the product data plate.
• MODEL NUMBER
BTS21
• SERIAL NUMBER
• How to cause cancer, birth defects or other reproductive harm. Replacement parts can also be obtained at one of our Authorized Service Centers.
• How to locate an...
Repair Sheet - Page 4
...(D4 2 76 411071004 * LOCK NUT (M10 1 77 0134010320 FRONT CABINET SUPPORT PLATE 1 78 410499007 * SCREW (M5 x 8 mm TRUSS HD 2 79 ...RYOBI 10 in . TABLE SAW - MODEL NUMBER BTS21
The model number will be found on a plate attached to the motor housing. Always mention the model number in all correspondence regarding your TABLE SAW or when ordering repair parts. PARTS LIST
KEY PART...
Repair Sheet - Page 5
... 0181010804 BLADE NUT (5/8-18 1 111 0134010225 INNER DUST COVER 1 112 410331003 * SCREW W/WASHER (M6 x 10 mm PAN HD 4 113 0134010226 OUTER DUST COVER 1 114 410031710 * CARRIAGE BOLT (5/16-18 x 1/2 in all correspondence regarding your TABLE SAW or when ordering repair parts. RYOBI 10 in. MODEL NUMBER BTS21
The model number will be found on a plate attached to the motor housing...
Repair Sheet - Page 6
...MITER FENCE ASSEMBLY (INC. RYOBI 10 in all correspondence regarding your TABLE SAW or when ordering repair parts.
4
6 3
7 2 1
8
5
9
FIGURE A
KEY NO.
1
2 3
4 5 6 7 8 9
PARTS LIST FOR FIGURE A
PART NUMBER
DESCRIPTION
QTY.
TABLE SAW - May Be Purchased Locally Always mention the model number in . MODEL NUMBER BTS21
The model number will be found on a plate attached to the...
Repair Sheet - Page 11
... correspondence regarding your TABLE SAW or when ordering repair parts.
14 15 21 16
10
12
11
17 18
7
8
1 3
19
20
13
SECTION "A"
2 4 5 6
9
PARTS LIST FOR SECTION "A"
KEY PART
NO. ANY REPAIR TO THIS TOOL REQUIRES DIELECTRIC TESTING TO INSURE CUSTOMER SAFETY AND TO COMPLY WITH COMPANY REQUIREMENTS.
* Standard Hardware Item - TABLE SAW - Always mention the model number in . NUMBER...
Repair Sheet - Page 12
RYOBI 10 in. TABLE SAW - MODEL NUMBER BTS21
WHITE LEAD
BRUSH ASSEMBLY
BLACK LEAD
MOTOR
WHITE LEAD
WHITE LEAD
GROUNDING
GREEN LEAD
BLACK LEAD
GREEN LEAD
BLACK LEAD
GREEN
GROUNDING LEAD
GROUNDING POWER CORD
MOTOR CORD
WIRING DIAGRAM
12
Ryobi RTS30 Reviews
We have not received any reviews for Ryobi yet.