Ryobi RTS20 Support and Manuals
Get Help and Manuals for this Ryobi item
Most Recent Ryobi RTS20 Questions
How To Repair Lockout Switch And Handle Or Lockout Bar
(Posted by benbailey 9 years ago)
Ryobi Rts20 Vs Bts20
Are the Ryobi BTS20 parts the same as their RTS20?
Are the Ryobi BTS20 parts the same as their RTS20?
(Posted by charlie30286 10 years ago)
How Many Horsepower Rts20 Ryobi?
Anyone have that answer, can't find it. No mention of that spec. important for me to make my decisi...
Anyone have that answer, can't find it. No mention of that spec. important for me to make my decisi...
(Posted by micheldion 10 years ago)
Fence Locking Lever Is Boke Need A New Part
(Posted by kimrnodak 11 years ago)
Replacement Parts
I recently purchased a Ryobi BT3000 10" Table saw w/stand. The miter gauge for it is missing; only...
I recently purchased a Ryobi BT3000 10" Table saw w/stand. The miter gauge for it is missing; only...
(Posted by mica4339 11 years ago)
Popular Ryobi RTS20 Manual Pages
English Manual - Page 3
... with sufficient set. A guard or other part that is damaged should wear safety glasses and be properly repaired or replaced by removing starter keys.
DON'T FORCE TOOL. When tool is recommended for . READ ALL INSTRUCTIONS
KNOW YOUR POWER TOOL. Read the operator's manual carefully. Form
habit of at least 14 is used outdoors, use of blade or...
English Manual - Page 4
...; SUPPORT LARGE PANELS. Inspect for and remove all "through cuts.
4 SPECIFIC SAFETY RULES
FIRMLY BOLT THE SAW TO A WORK BENCH OR LEG STAND at an authorized service facility. Size and shape can pull your hands. When ripping narrow stock, always use only identical replacement parts. Repair or replace a damaged or worn cord immediately. Have defective switches replaced by...
English Manual - Page 5
... NOT USE THE MITER GAUGE AND RIP FENCE during the same operation.
NEVER use to instruct other masonry products, and • arsenic and chromium from these chemicals are: • lead from lead-based paints, • crystalline silica from the power source.
PROVIDE ADEQUATE SUPPORT to the rear and sides of the saw table for wide...
English Manual - Page 7
..., which , if not avoided, may result in property damage. SAVE THESE INSTRUCTIONS
7 For service we suggest you do not understand the warnings and instructions in death or serious injury. If you return the product to the nearest AUTHORIZED SERVICE CENTER for repair. Call Ryobi customer service for use over eyeglasses or standard safety glasses with this product...
English Manual - Page 9
... tool is being guided by guiding it applies to the table surface. Dado Cut A non-through or partial cut removing a wedge from the cutterhead. Saw Blade Path The area over the jointer planer cutterhead during cutting operations. Chamfer A cut . Miter Cut A cutting operation made with the blade. These aids help control the workpiece by a fence, miter gauge, or other aids...
English Manual - Page 11
... blade replacement. RIP FENCE - A metal piece of the blade guard assembly, slightly thinner than the speed of the rip fence for through-sawing cuts.
BEVEL SCALE -
MITER GAUGE GROOVEs - This table extension at 90° and 45°. Place the key in which helps keep the blade guard down over the saw has an easy access power switch located below the front rail. BLADE GUARD...
English Manual - Page 12
... and the blade.
Failure to heed this manual for all through the table and is not in use the blade guard assembly for the basic cuts: cross cuts, miter cuts, bevel cuts, and compound cuts. POWER SWITCH
This saw is equipped with a handwheel on the front of this warning may cause the workpiece to start the tool.
Detailed instructions are...
English Manual - Page 15
... the settings, refer to do not operate this manual.
If any parts are missing, do so could result in serious personal injury.
15
Fig. 7 to the blade. warning...table saw on a level work surface. NEVER operate the saw is securely mounted to modify this tool or create accessories not recommended for use this warning can result in . Warning:
If any parts are replaced...
English Manual - Page 16
... movement can cause the throat plate to bow or bend. to remove/replace the THROAT PLATE
See Figure 10.
Lower the blade by turning the height/bevel adjusting handwheel counterclockwise.
Loosen the screws in the throat plate. Lift the throat plate from the end of the four mounting holes should be mounted to a firm supporting surface such as...
English Manual - Page 17
... the throat plate.
Proper installation of the blade guard assembly means that the saw base. Check the blade guard assembly for free blade rotation. To loosen the blade: Using the smaller blade wrench,...install dust bag
See Figure 11.
To tighten the blade: Using the smaller blade wrench, place the flat open end
on the flats on the table saw . This will be set...
English Manual - Page 19
...screw in . Repeat the above steps for clarity, do not operate the saw without the blade guard unless specifically instructed to the 18 in .
Adjust the indicator (left or ...rear extension rod and tighten.
Open the extension table completely.
on the scale.
Remember that a careless fraction of this manual are shown with side shields when operating tools. WARNING:
...
English Manual - Page 24
.... Using a framing square, set the rip fence 2 in the Adjustment section of this manual. Check for a smooth gliding action. The miter gauge provides greater accuracy in . There are recommended.
Blade
Rip fence
Scale
2 in angled cuts. When making a 90° cross cut (the blade tilted in relation to the table) the miter gauge should be turned 60°...
English Manual - Page 34
.... To replace the blade with an accessory blade, follow the instructions provided with blade.
Possible serious injury can occur if hands come in good workpieces.
TO REPLACe THE BLADE
See Figures 43 - 45.
Unplug the saw.
Lower the saw has been adjusted at the factory for free blade rotation. The table saw blade, raise the blade guard, and remove the throat plate...
English Manual - Page 35
.... NOTE: Securely tighten throat plate screws. The angle settings of the blade has moved completely to the left . Lock the angle by pushing the bevel locking lever and retighten the adjustment bolt.
Turn the bevel handle until the bottom of your saw . Raise the blade and the blade guard.
If the blade is not an exact...
English Manual - Page 40
... obtain Customer or Technical Support please contact us at www.ryobitools.com or by power sanding, sawing, grinding, drilling, and other construction activities contains chemicals known to obtain Replacement Parts:
Replacement parts can be purchased online at 1-800-525-2579. Your risk from chemically-treated lumber. Replacement parts can also be obtained at one of Ryobi Limited used under...
Ryobi RTS20 Reviews
We have not received any reviews for Ryobi yet.