Optoma W351 Support and Manuals
Popular Optoma W351 Manual Pages
Manual - Page 1
... 35 DISPLAY 36 DISPLAY | 3D 39 SETUP 40 SETUP | Security 42
SETUP | Audio Settings 44 SETUP | LAN Settings 45 SETUP | Advanced 47 OPTIONS 48 OPTIONS | Remote Settings 50 OPTIONS | Advanced 51 OPTIONS | Lamp Settings 52 OPTIONS | Optional Filter Settings.... 53
Appendices 54 Troubleshooting 54 Replacing the Lamp 60 Installing and Cleaning the Filter.......62 Compatibility Modes 63...
Manual - Page 3
... the on-screen display "OPTIONS | Lamp Settings" menu after
replacing the lamp module (refer to cool down .
To replace the
▀■ Warning-
will not turn on the
projector. Please contact your eyes.
▀■ Warning- The bright light may cause electric shock.
▀■ Warning- Follow instructions as possible.
3 English This projector will detect the life of...
Manual - Page 5
...projector is used in a classroom, adequately supervise students when they are asked to point out something on model.
▀■ XGA (1024x768) / WXGA (1280X800) Native resolution ▀■ HD compatible - 720p and 1080p supported...may vary depending on the screen.
▀■ In order to minimize the lamp power, use room blinds to reduce ambient light levels.
Keep your back to ...
Manual - Page 6
Projector
Due to ensure all parts listed below are in the box.
Laser
Page+
Keystone
Volume
1
4 HDMI
7 User1
Source
2 Menu
5 VGA
8 User2
0
3 3D 6 Video 9 User3
Resync
IR Remote Control
VGA Cable(*) Carrying case(*)
English 6
varies by regional offerings and model specs.
User's Manual Warranty Card Quick Start Card WEEE Card
(for...
Manual - Page 9
... jack)
ry.
Audio Output Connector (3.5mm mini jack)
Optoma service for details.
10. USB service and remote mouse
13. RJ45
9 English Composite Video Input...support in VGA2-IN/ YPbPr.
5.
(PC Analog Signal/Component Video Input/HDTV/YPbPr) VGA1-IN/YPbPr/ Connector
(*) The interface
(PC Analog Signal/Component Video Input/HDTV/YPbPr/
is subject to
model's specifications...
Manual - Page 30
.... (#2) "Signal" is only supported in Analog VGA (RGB) signal. (#3) For XGA model only. (#4) For WXGA model only. 16:9 or 16:10 depend on "Screen Type" setting. (#5) "3D Sync Invert" is only available when 3D is enabled and this mode
3D is for DLP link glass only. (#6) The function depends on model's specifications.
Manual - Page 35
..., frequency items will appear for user to manually tune and saved in Analog VGA (RGB) signal. If you use this function to correct it. Use this function, the Phase, frequency items are grayed out, and if Signal is only supported in settings after that for next time projector turns off and on again. If...
Manual - Page 42
... number button on the remote, then press "Enter" to enter your password.
Change Password:
1.
Press "
" to set how long (Month/Day/Hour) the projector can be requested to confirm.
4. Press " " to confirm. User Controls
SETUP | Security
"Security" depends on the projector without
password verification. Security
On: Choose "On" to use security verification...
Manual - Page 45
... value is 255.255.255.0. If DHCP is Off, manually set the IP Address, Subnet Mask, and Gateway. IP Address
Select an IP address. User Controls
SETUP | LAN Settings
Network State Choose "Connect" to enable LAN network function. Choose "Disconnect" to which the projector is connected, the IP address will automatically be acquired...
Manual - Page 46
English 46
MAC Address
Display MAC addresss for the projector. User Controls
DNS
Check the DNS Server IP address with your network/system administrator if you wish to save the changes made in network configuration settings. Default value is 192.168.0.51. Apply
Choose "Yes" to configure it manually.
Manual - Page 54
... following steps. 5. Refer to the "Replacing the lamp" section.
Ensure that your display resolution setting is lower than or equal
to UXGA
(1600 × 1200). 6.
Verify the resolution setting is lower than or equal to UXGA (1600 × 1200). 4. Appendices
Troubleshooting
If you experience a problem with your local reseller or service center.
No image appears on...
Manual - Page 55
.... See page 35 for detailed information. Press the appropriate keys listed below for your computer's manual for more information. Change the monitor color setting on "Show all equipment including the projector. First, follow the steps above to projector. Appendices
7. choose the resolution mode you experience difficulty changing resolutions or your presentation
If...
Manual - Page 61
... 5
3 4
7
Lamp Replacement Procedure:
1. Lift up and remove the lamp cord. 4 8. Lamp Reset: (i) Press "Menu" (ii) Select "OPTIONS" (iii) Select
"Lamp Settings" (iv) Select "Lamp Reset" (v) Select "Yes".
61 English The screws on the lamp cover and the lamp cannot be removed.
The projector
cannot be turned
on if the lamp
cover has not...
Data Sheet - Page 1
... impressive list of standard features, the Optoma W351 will win your audience with its sharp, easy to 8000 hours lamp life and whisper quiet operation. Full 3D compatibility, Optoma True-Vivid color tuning technology with superior connectivity and an impressive list of standard features.
MULTIMEDIA PROJECTOR W351
PROJECT YOUR IDEAS
3800 lumens with 20,000:1 contrast ratio for...
Data Sheet - Page 2
...W351
OPTICAL/TECHNICAL SPECIFICATIONS
Display Technology
Single 0.65" DC3 DMD DLP® Technology by Texas Instruments™
Native Resolution
WXGA (1280 x 800)
Maximum Resolution
WUXGA (1920 x 1200)
Brightness
3800 lumens
Contrast Ratio
20,000:1 (full on/full off)
Displayable Colors
1.07 Billion
Lamp... F=2.5-2.67, f=21.8-23.98 mm 1.1x manual zoom and focus
Digital Zoom
1.0 ~ 2.0...
Optoma W351 Reviews
Do you have an experience with the Optoma W351 that you would like to share?
Earn 750 points for your review!
We have not received any reviews for Optoma yet.
Earn 750 points for your review!