Optoma HD806 Support and Manuals
Get Help and Manuals for this Optoma item
View All Support Options Below
Free Optoma HD806 manuals!
Problems with Optoma HD806?
Ask a Question
Free Optoma HD806 manuals!
Problems with Optoma HD806?
Ask a Question
Most Recent Optoma HD806 Questions
Will Not Power On
(Posted by juangetz 12 years ago)
Popular Optoma HD806 Manual Pages
User Manual - Page 1
...operate ...20 Menu Tree...21 Image...22 Display ...26 Setup...29 System...32
Appendices 36 Troubleshooting 36
Image Problems 36 Intermission Problems 38 Projector Status Indication 39 Remote Control Problems 40 Replacing the Lamp 41 Compatibility Modes 42 RS232 Commands and Protocol Function List 43 Ceiling Mount Installation 46 Optoma Global Offices 47 Regulation & Safety notices 49
1
User Manual - Page 2
... Clean only with the manufacturer's instructions
A. Only use this projector. 2. ate normally, or has been dropped. Please call Optoma to be referred to an authorized service center near water or moisture. ... instructions -before using this projector near you to dangerous voltages or other apparatus (including amplifiers) that will not interfere with its ventilation openings. Install ...
User Manual - Page 3
... in this may hurt your local reseller or service center to change the lamp when it shows warning messages.
To replace
the lamp, follow the
procedures listed under
"Replacing the Lamp"
section on the screen. English
Usage Notice
Precautions
Please follow all replacement instructions. See page 41. When switching the projector off, please ensure the cooling cycle has been...
User Manual - Page 6
...95" DLP® projector.
ing, scaling, image enhancement and color) &#...▀■ Macintosh compatible ▀■ Full function IR remote control with back light ▀■ Advanced vertical digital keystone...Optoma's patent-pending O2AirTM Photo Catalyst air purification technology ▀■ HDMI & DVI support HDCP function. ▀■ HDMI(support HDMI 1.3) x2, DVI-I (support...
User Manual - Page 7
...; User's Manual Warranty Card Quick Start Card
DVI to make sure your dealer immediately if anything is complete.
English
Projector with all the items shown below. Contact your unit is missing. Introduction
Package Overview
This projector comes with lens cap
Power Cord 1.8m
RS232 Cable 1.8m
RCA Component Cable IR Remote Controller...
User Manual - Page 13
.... 4. Ensure that "Source Lock" has been set to switch between inputs. English
Installation
Powering On/Off the Projector
Powering On the Projector
1. Turn on the projector first and then select the signal sources.
1
2
13 The startup screen will turn red. 3. Turn on the lamp by pressing " " button on the remote control to "Off".
▀■ If you...
User Manual - Page 14
... overheated. Press the " " button to turn the projector back on the projector immediately following a power off the projector
1. If you wish to turn on , you should contact your local dealer or our service center. The projector will see a message displayed on again after 5 seconds. 2. Installation
Powering off procedure. If the problem persists, you must wait until the...
User Manual - Page 18
... lightest and darkest parts of the image. (refer to be displayed. After the initial setup and fine tuning ... to the "Power On/Off the Projector" section on page 33 for more information. User Controls
Using the Remote Control
Power
Refer to your selection.... again. Brightness Adjust the brightness of the image to have encoding error near any edge of the image to page 35).
/ Image ...
User Manual - Page 21
...|Advanced
Noise Reduction Gamma
Degamma True Vivid Edge Enhance B/W Extension Color Temp
DISPLAY SYSTEM SYSTEM|Lamp Setting SETUP
Format Overscan Edge Mask H Image Shift V Image Shift V Keystone SuperWide
Menu Location Lamp Setting
Projection Image AI
IRIS Test Pattern Background 12V Trigger
Lamp Hour Lamp Reminder
Brite Mode Lamp Reset
Exit
Language
Input Source
Source Lock High Altitude Auto...
User Manual - Page 36
...the "Replacing the lamp" section.
Make sure you have removed the lens cap and the projector is
switched on the "Advanced Properties" button. Click on . If the projector is lower than UXGA
(1600 x 1200). (*) 4.
Verify that your projector, please refer to the following steps.
5. Appendices
Troubleshooting
If you experience a problem with your display resolution setting is...
User Manual - Page 37
... presentation If you need
Noottee
under the "Models" box. 8.
Each has a different way to correct it compatible with the projector.
37 Unstable or flickering image Use "Tracking" to be reactivated. for more information. Change the monitor color setting on "Show all equipment including the projector. T he screen of the monitor display is...
User Manual - Page 38
...:9], [ Letter-Box], [ Native] button
on the remote control or [Menu] on the projector lens. Make sure the projection screen is reversed Select "System-->Projection" from the projector. If you play 4:3 format DVD title, please change the format as 4:3 in projector OSD.
jection direction. Intermission Problems
The projector stops responding to 12.0 meters) from the...
User Manual - Page 39
... of life, it will not turn on until the lamp module has been replaced. To replace the lamp, follow the procedures in the "Replacing the Lamp" section on and Lamp lighting Power off (Cooling) Error (Lamp fail) Error (Thermal fail) Error (Fan fail) Error (Over Temp.)
Power LED (Red)
Power LED (Blue)
Temp-LED Lamp-LED
Flashing
Flashing
Flashing
Flashing
Message Reminders ...
User Manual - Page 40
If so, replace weak batteries in
the remote control.
40 trol and the projector.
Appendices
Over temperature:
Replacing the lamp:
Remote Control Problems
If the remote control does not work Check the operating angle for the remote control is approximately
±22.5°.
Make sure there are exhausted. Move to within 6 m (20 ft) of the projector.
...
User Manual - Page 41
... do not drop the lamp module or touch the lamp bulb. Lamp Reset: (i)Press "Menu" -> (ii)Select "System" -> (iii)Select "Lamp setting" ->(iv)Select "Lamp reset" -> (v)Select "Yes".
41 Warning: Lamp com-
When the lamp life is hot!
Make sure
it is replaced. English
Appendices
Replacing the lamp
The projector automatically detects the lamp life.
Allow service center to cool...
Optoma HD806 Reviews
We have not received any reviews for Optoma yet.