Optoma HD806 Support Question
Optoma HD806 Support Question
Find answers below for this question about Optoma HD806.Need a Optoma HD806 manual? We have 1 online manual for this item!
Question posted by juangetz on February 8th, 2012
Will Not Power On
The person who posted this question about this Optoma product did not include a detailed explanation. Please use the "Request More Information" button to the right if more details would help you to answer this question.
Current Answers
Related Optoma HD806 Manual Pages
User Manual - Page 1
... Control Panel...9 Connection Ports 10 Remote Control...11
Installation 12 Connecting the Projector 12 Powering On/Off the Projector 13
Powering On the Projector 13 Powering Off the projector 14 Warning Indicator 14 Adjusting the Projected Image 15 Adjusting the Projector's Height 15 Adjusting the Projector's Zoom / Focus 16 Adjusting Projected Image Size 16
User Controls 17 Control...
User Manual - Page 2
... of electric shock to persons. Refer all requirements of the Canadian Interference-Causing Equipment Regulations. Servicing is required when the projector has been damaged in any heat sources, such as power supply cord or plug is intended to alert the user to the presence of import operating and maintenance (servicing) instructions in...
User Manual - Page 3
... . The bright light may cause electric shock. When switching the projector off, please ensure the cooling cycle has been completed before disconnecting power. Allow 90 seconds for the projector to change the lamp when it shows warning messages.
Do not look into the projector's lens when the lamp is on until the
lamp module...
User Manual - Page 4
... unit. ▀■ Use under the following conditions:
- Extremely heat, cold or humidity. - In areas susceptible to clean the
display housing.
▀■ Disconnect the power plug from AC outlet if the product is not
being used for ventila- Usage Notice
Do: ▀■ Turn off the product before cleaning. ▀...
User Manual - Page 5
... when they do not also have to the audience; The best way to achieve this ensures that projectors are asked to point out something on the screen. ▀■ In order to minimize the lamp power needed, use room blinds to reduce ambient light levels.
5 English
Usage Notice
Eye Safety Warnings
▀...
User Manual - Page 7
Contact your unit is missing. Check to VGA Adaptor
VGA Cable 1.8m
7
English
Projector with all the items shown below. Introduction
Package Overview
This projector comes with lens cap
Power Cord 1.8m
RS232 Cable 1.8m
RCA Component Cable IR Remote Controller for YPbPr 2.0m
Available in European version only
2 x AA Batteries
Noottee
Due to...
User Manual - Page 9
Power Indicator LED 3. Source Select 8. Power and IR Receiver 2. Menu (On/Off) 6. Enter
7
8
9
9 Four Directional Select Keys 7. Lamp Indicator LED 4. English
Introduction
Control Panel
1
2
3
4
5
6
1. Temp Indicator LED 5. Re-Sync 9.
User Manual - Page 10
S-Video Input Connector 5. HDMI 1 Connector 7. RS232 Input Connector 4. DVI-I Input Connector (PC Digital and DVI-HDCP) 6. Kensington MicrosaverTM Lock Port
10 Power Socket 10. Component Video Input Connector 9. HDMI 2 Connector 8. Introduction
Connection Ports
12
3
4
5
67
8
9
10
1. +12V Relay Connector 2. Composite Video Input Connector 3.
User Manual - Page 12
Installation
Connecting the Projector
SCART DVD Player
7
RGB
DVI
+12V Relay Output
8
9
3
2
1
Video Output
4
56 10
S-Video Output
DVD Player, Set-top Box, HDTV receiver
Noottee
Due to the difference in applications for each country, some regions may have different accessories.
1...Power Cord 2 DVI to VGA Adaptor (For European Only) 3...RS232 Cable 4 Composite...
User Manual - Page 13
... sources at the same time, press the "Source" button on the control panel or direct source key on the projector first and then select the signal sources.
1
2
13 The projector will turn red. 3. The Power LED will display in approximately 30 seconds. Ensure that "Source Lock" has been set to "Off".
▀■...
User Manual - Page 14
... standby mode, simply press " " button to confirm, otherwise the message will disappear after it has cooled down . Disconnect the power cord from the electrical outlet and the projector. 4.
Installation
Powering off procedure. The projector will automatically shut itself down. See page 47.
14 Please contact your local dealer or our service center. Press the...
User Manual - Page 17
...
Control Panel & Remote Control
There are two ways for you to your item selection. Using the Control Panel
Power Source
Menu
Four Directional Select Keys Enter Re-Sync
Refer to the input source.
17
Confirm your selection.
Automatically synchronizes the projector to the "Power On/Off the Projector" section on -screen display (OSD) menu.
User Manual - Page 18
... to select items or make adjust-
Brite Mode Increase the brightness of the image. Use Edge Mask "On" if image source happens to the "Power On/Off the Projector" section on pages 13-14.
To exit OSD, Press "Menu" again. Four Directional Select Keys
Use
to your item selection.
Scale the image...
User Manual - Page 27
...:1 aspect ratio using the 4:3 mode to remove video encoding noise on the projection screen. Some Letter-Box DVDs are no black bars, the full lamp power and vertical resolution is enhanced for 16x9 Display in a wide 2.35:1 image.
English
User Controls
Noottee
(*) Each I/O has different setting of "Overscan".
(*) "Image mode-->TV...
User Manual - Page 30
...the fans at full speed continuously to match the fre- Auto Power Off
Sets the interval of power-off of your computer's graphic card. Signal
Phase: ...or flickering image, use this function to make an adjustment.
Tracking : Synchronizes the signal timing of the projector. quency of the system, if there is no signal input. (In minutes)
RGB/HDTV Source
Video Source
Noottee...
User Manual - Page 36
..."Re-Sync" on the control panel. If you have removed the lens cap and the projector is
switched on.
Please
refer to UXGA (1600 x 1200) resolution. (*)
36 If a problem ... than UXGA
(1600 x 1200). (*) 4. Click on -screen Ensure all the cables and power connections are correctly and
securely connected as described in the "Installation" section.
Ensure the pins...
User Manual - Page 38
... player.
tance 4.9 to 39.4 feet (1.5 to all controls If possible, turn off the projector, then unplug the power cord
and wait at least 20 seconds before reconnecting power.
38 If you play anamorphic DVD or 16:9 DVD, the projector will also need to adjust the aspect ratio by referring to the following: ...
User Manual - Page 39
... on until the lamp module has been replaced. If this happens, the projector will burn out and may
make a loud popping sound. To replace the lamp, follow the procedures in the "Replacing the Lamp" section on and Lamp lighting Power off (Cooling) Error (Lamp fail) Error (Thermal fail) Error (Fan fail) Error...
User Manual - Page 41
... "System" -> (iii)Select "Lamp setting" ->(iv)Select "Lamp reset" -> (v)Select "Yes".
41 Warning: Lamp com-
Lamp Replacing Procedure: 1. Switch off the power to the projector by pressing the Power
button.
2. Allow the projector to cool down at least 30 minutes before changing lamp! When the lamp life is nearing the end of personal injury...
User Manual - Page 45
...s Color
* 0 IR 039
* 0 IR 039
-- s mode
* 0 IR 042
* 0 IR 042
-- g Get Projector status
*004 xx *005 xx
ACK Default ACK Default ACK Default ACK Default ACK Default ACK Default ACK Default ACK Default ACK Default...: Testing xx means 00 : Brite Mode Off 01 : Brtire Mode
xx means projector is in 00 : Standby mode 01 : Power On 03: Cooling on or cooling off 04: Lamp error 05: Thermal error
...
Similar Questions
Optoma Ep1691 Power
i have an optoma EP1691 that i have not used for a long time.. i tried plugging in to the wall outle...
i have an optoma EP1691 that i have not used for a long time.. i tried plugging in to the wall outle...
(Posted by elitayam 8 years ago)
Optoma Hd 180 Internal Power Supply
I have an HD projector i got at Costco approximately 2 years ago. It has been a great projector. How...
I have an HD projector i got at Costco approximately 2 years ago. It has been a great projector. How...
(Posted by waves133 10 years ago)
R+eplaced The Bulb But Now The Projector Has Power To It But It Will Not Turn On
(Posted by jlanpher 11 years ago)
Steady Blue Led When Power On Turns Off When Signal Is Put Thru Projector
The projector works fine. After warm up the power on button is supposed to be a steady blue. It is a...
The projector works fine. After warm up the power on button is supposed to be a steady blue. It is a...
(Posted by Gooddoghoney 12 years ago)
My Projector Has No Power
No power, ned's lite bulb does not come on
No power, ned's lite bulb does not come on
(Posted by gterrald2 12 years ago)