Optoma HD8200 Support and Manuals
Get Help and Manuals for this Optoma item
View All Support Options Below
Free Optoma HD8200 manuals!
Problems with Optoma HD8200?
Ask a Question
Free Optoma HD8200 manuals!
Problems with Optoma HD8200?
Ask a Question
Popular Optoma HD8200 Manual Pages
User Manual - Page 1
... 19 On-screen Display Menus 21
How to operate ...21 Menu Tree...22 Image...23 Display ...28 System...31 Setup...35
Appendices 38 Troubleshooting 38
Image Problems 38 Other Problems 39 Projector Status Indication 40 Remote Control Problems 41 Replacing the Lamp 42 Compatibility Modes 44 RS232 Commands and Protocol Function List 45 Ceiling Mount Installation 48 Optoma Global Offices...
User Manual - Page 2
... spilled on a crowded coffee table, sofa, bed, etc. Please call Optoma before you to install the projector in the projector or something is loose inside. Do not install near water or moisture.
Do not use attachments/accessories specified by appropriate service personnel.
Do not use the projector near heat sources such as radiators, heaters, stoves or any...
User Manual - Page 3
... the onscreen display "System|Lamp Setting" menu after replacing the lamp module (refer to cool down . When switching the projector off, please ensure the cooling cycle has been completed before disconnecting power. English
Usage Notice
Precautions
Please follow the procedures listed under "Replacing the Lamp" section on page 42.
Follow instructions as possible.
Do not...
User Manual - Page 6
... Cable
1.8m
(Not Available in each Country, some regions may have different accessories. If something is missing, please contact Optoma customer service.
POWER LAMP TEMP
STANDBY
Noottee
Projector with lens cap
Due to ensure all parts listed below are in the box. Introduction
Package Overview
Unpack and inspect the box contents to different applications in...
User Manual - Page 13
Noottee
Turn on the remote control.
The projector will detect the source automatically and will display in approximately 30 seconds. POWER LAMP TEMP
STANDBY
1
POWER LAMP TEMP
2
STANDBY
13 English
Installation
Powering On/Off the Projector
Powering On the Projector
1. The first time you use the projector, you want to "Off".
▀■ If you connected multiple sources at...
User Manual - Page 14
Contact the nearest service center if the projector displays these
▀■
When the "TEMP" indicator turns red, tor has overheated. Press the " " button on the remote control or " " button on the projector immediately following message on the screen. The cooling fans continue to operate for about 60 seconds for cooling cycle and the Power LED will display...
User Manual - Page 25
... user to switch among the pre-sets to obtain different image effects. (Off/On)
Color Temp
If set up gamma curve type. B/W Extension
Black and White Extension can stretch the black and white levels to automatically increase the contrast of visible noise interlaced signals. After the initial setup and fine tuning is from "0" to...
User Manual - Page 29
...the image in a video image.
ent setting of video source.
If you use an...using full resolution.
Overscan the image to magnify an image on the projection screen. In this type of an image. Press the to remove ...or to watch a 2.35:1 content (include Anamorphic DVD and HDTV film source) that support anamorphic wide is not 4:3, there will not look right when displayed in a wide 2....
User Manual - Page 38
... information. Please
refer to the "Replacing the Lamp" section.
Make sure you experience a problem with your local reseller or service center. Image is out of focus Make sure the Lens cap is removed. Adjust the Focus Ring on the projector lens. Make sure the projection screen is between the required distance...
User Manual - Page 39
... the
screen and below the bottom of life, it is reversed
Select "System-->Projection" from the OSD to make a loud popping sound. Other Problems
The projector stops responding to all controls If possible, turn on page 42.
39 If this happens, the projector will burn out and may
make an adjustment. To replace...
User Manual - Page 40
... light => No light =>
Projector Status Indication
LED states
Message
Standby State (Input power cord) Standby State (Burn in mode) Power on and Lamp lighting
Power off (Cooling)
Power LED (Red)
Power LED (Blue)
Temp-LED (Red)
Lamp-LED (Orange)
Flashing *
Error (Lamp fail)
Error (Thermal fail)
Error (Fan fail)
Flashing
Error (Over Temp.)
* Power LED be ON...
User Manual - Page 41
...
Appendices
On Screen Messages Fan failed:
The projector will switch off automatically.
Over temperature:
The projector will switch off automatically.
Replacing the lamp:
Lamp is within 6 m (20 ft) of the projector.
Make sure batteries are inserted correctly. Replace batteries if they are not any obstructions between the remote con- Replcement...
User Manual - Page 47
... Setting... from projector
232 ASCII Code HEX Code
Function
Projector Return ...Ceiling
~XX150 1
7E 30 30 31 35 30 20 31 0D
Information
OKabbbbcdddde a : 0/1=Off/On
bbbb: Lamp Hour
c: source 0/1/2/3/4
= None/HDMI 1/HDMI 2/DVI/Component/VGA/S-Video/Video
dddd: FW version
e : Display mode 0/1/2/3/4/5
=Cinema/ Bright/ Photo/ Reference/ User
~XX151 1
7E 30 30 31 35 31 20 31 0D
Model...
User Manual - Page 48
... ceiling
mount from incorrect installation will be sure to keep at least 10cm gap between the ceiling and the bottom of the projector. 3. Avoid installing the projector near a heat source.
220.00mm (8.66")
20.00mm (0.79")
260.00mm (10.23")
81.19mm (3.20")
97.99mm (3.86")
48
120.00mm (4.72")
120.00mm (4.72") jector met the following specifications...
User Manual - Page 49
English
Appendices
Optoma Global Offices
For service or support please contact your local office. USA
715 Sycamore Drive
Tel : 408-383-3700
Milpitas, CA 95035, USA
Fax: 408-383-3702
www.optomausa.com
Service : services@optoma.com
Canada
5630 Kennedy Road, Mississauga,
ON, L4Z 2A9, Canada
Tel : 905-361-2582
www.optoma.ca
Fax: 905-361-2581
Europe...
Optoma HD8200 Reviews
We have not received any reviews for Optoma yet.