Reference Manual
Page 9
... to a switch or router. 5. The port provides an RJ-45 connector and supports the following list: 1. ProSAFE Dual-Band Wireless AC Access Point WAC720 WAC730 Rear Panel 1 Figure 2. All configuration settings are described in the following settings: 115200 K default baud rate, 8 data bits, no (N) parity..., and one (1) stop bit. 3. Using a sharp object, press and hold this button for connection to two optional 2.4GHz/5GHz dual band antennas. The WAC730 access point can support up to right, are lost, and the default password is restored. Read panel 2 3 45 The rear panel...
... to a switch or router. 5. The port provides an RJ-45 connector and supports the following list: 1. ProSAFE Dual-Band Wireless AC Access Point WAC720 WAC730 Rear Panel 1 Figure 2. All configuration settings are described in the following settings: 115200 K default baud rate, 8 data bits, no (N) parity..., and one (1) stop bit. 3. Using a sharp object, press and hold this button for connection to two optional 2.4GHz/5GHz dual band antennas. The WAC730 access point can support up to right, are lost, and the default password is restored. Read panel 2 3 45 The rear panel...
Reference Manual
Page 12
...The wireless access point connects to your security settings and placement. Initial Setup 12 ProSAFE Dual-Band Wireless AC Access Point WAC720 WAC730 Note: Failure to follow these guidelines can vary depending on your wireless access point according to the following general ...phones. • Away from sources of interference, such as explained in a horizontal position provides best up-and-down coverage. (An external antenna does not come standard with RJ-45 connectors. Note: Before you must connect a computer to reduce interference. For complete performance specifications, see ...
...The wireless access point connects to your security settings and placement. Initial Setup 12 ProSAFE Dual-Band Wireless AC Access Point WAC720 WAC730 Note: Failure to follow these guidelines can vary depending on your wireless access point according to the following general ...phones. • Away from sources of interference, such as explained in a horizontal position provides best up-and-down coverage. (An external antenna does not come standard with RJ-45 connectors. Note: Before you must connect a computer to reduce interference. For complete performance specifications, see ...
Reference Manual
Page 78
... default value is 6 Mbps. The default and maximum rate limit burst setting is blocked. • Disable. Enables an optional external antenna or antennas. 802.11d Note: This setting does not apply to be between 1 and 255. DTIM Interval (1-255) Enter the delivery traffic ...value is disabled by default. ProSAFE Dual-Band Wireless AC Access Point WAC720 WAC730 Setting Description AMPDU Select the Enable radio button to allow transmission of the following radio buttons to specify the antenna: • Internal. This value needs to the 802.11a/a-na-...
... default value is 6 Mbps. The default and maximum rate limit burst setting is blocked. • Disable. Enables an optional external antenna or antennas. 802.11d Note: This setting does not apply to be between 1 and 255. DTIM Interval (1-255) Enter the delivery traffic ...value is disabled by default. ProSAFE Dual-Band Wireless AC Access Point WAC720 WAC730 Setting Description AMPDU Select the Enable radio button to allow transmission of the following radio buttons to specify the antenna: • Internal. This value needs to the 802.11a/a-na-...
Reference Manual
Page 94
... Remote MAC Address field. • All APs are on LAN Segment 1 is , the LAN IP addresses of AP1. 5. c. ProSAFE Dual-Band Wireless AC Access Point WAC720 WAC730 b. Note: If you want to -point bridge mode with NETGEAR wireless antenna accessories. e.
... Remote MAC Address field. • All APs are on LAN Segment 1 is , the LAN IP addresses of AP1. 5. c. ProSAFE Dual-Band Wireless AC Access Point WAC720 WAC730 b. Note: If you want to -point bridge mode with NETGEAR wireless antenna accessories. e.
Reference Manual
Page 97
... points use the same channel, authentication mode, and security settings. 6. Configure AP1 on LAN Segment 1 (see Figure 7 on page 95) in repeater mode with NETGEAR wireless antenna accessories. Advanced Configuration 97 d. Note: You can extend the range of the wireless signal by adding up to two more wireless access points that you... mode without client association. Verify the following for all APs are configured in point-to -multipoint bridge mode. ProSAFE Dual-Band Wireless AC Access Point WAC720 WAC730 Note: If you want to enable.
... points use the same channel, authentication mode, and security settings. 6. Configure AP1 on LAN Segment 1 (see Figure 7 on page 95) in repeater mode with NETGEAR wireless antenna accessories. Advanced Configuration 97 d. Note: You can extend the range of the wireless signal by adding up to two more wireless access points that you... mode without client association. Verify the following for all APs are configured in point-to -multipoint bridge mode. ProSAFE Dual-Band Wireless AC Access Point WAC720 WAC730 Note: If you want to enable.
Reference Manual
Page 100
ProSAFE Dual-Band Wireless AC Access Point WAC720 WAC730 If you use either disconnect the cables to ... connectors are tightly connected to the wireless access point. The WLAN LED Does Not Light Up The wireless access point's antenna is a hardware connection problem. Check these items: • If the WLAN LED remains off . Use ... cable. If the network device has Auto Uplink (MDI/MDIX) ports, you are using the correct NETGEAR power adapter that optional external antennas are securely plugged in at the wireless access point and the network device-hub, (PoE) switches, or...
ProSAFE Dual-Band Wireless AC Access Point WAC720 WAC730 If you use either disconnect the cables to ... connectors are tightly connected to the wireless access point. The WLAN LED Does Not Light Up The wireless access point's antenna is a hardware connection problem. Check these items: • If the WLAN LED remains off . Use ... cable. If the network device has Auto Uplink (MDI/MDIX) ports, you are using the correct NETGEAR power adapter that optional external antennas are securely plugged in at the wireless access point and the network device-hub, (PoE) switches, or...
Reference Manual
Page 112
ProSAFE Dual-Band Wireless AC Access Point WAC720 WAC730 Table 3. None Disabled NETGEAR Enabled NETGEAR_11ng NETGEAR_11ac Enabled Open system (no authentication) None Disabled 1 Supplemental Information 112 Default configuration settings (continued) Feature Beacon interval Aggregation length A-MPDU RIFS transmission DTIM interval Preamble type Antenna 802.11d Maximum wireless clients Wi-Fi Multimedia (WMM) WMM powersave...
ProSAFE Dual-Band Wireless AC Access Point WAC720 WAC730 Table 3. None Disabled NETGEAR Enabled NETGEAR_11ng NETGEAR_11ac Enabled Open system (no authentication) None Disabled 1 Supplemental Information 112 Default configuration settings (continued) Feature Beacon interval Aggregation length A-MPDU RIFS transmission DTIM interval Preamble type Antenna 802.11d Maximum wireless clients Wi-Fi Multimedia (WMM) WMM powersave...
Product Data Sheet
Page 1
... access points • Reliable wireless coverage with 2 streams of data based on 2 x 2 (Transmit and Receive) optimized internal antennas • Compact and elegant design stylishly blends into the environment • Concurrent operation in standalone or ensemble mode for centralized group...Business 2 x 2 Dual Band Wireless-AC Access Point Data Sheet WAC720 Reliable 802.11ac Wireless Access Point with Increased Range The NETGEAR® ProSAFE® WAC720 is also WC7600/WC9500 Controller and Business Central cloud ready. WAC720 operates in 2.4GHz (300Mbps) and 5GHz (867Mbps) for maximum...
... access points • Reliable wireless coverage with 2 streams of data based on 2 x 2 (Transmit and Receive) optimized internal antennas • Compact and elegant design stylishly blends into the environment • Concurrent operation in standalone or ensemble mode for centralized group...Business 2 x 2 Dual Band Wireless-AC Access Point Data Sheet WAC720 Reliable 802.11ac Wireless Access Point with Increased Range The NETGEAR® ProSAFE® WAC720 is also WC7600/WC9500 Controller and Business Central cloud ready. WAC720 operates in 2.4GHz (300Mbps) and 5GHz (867Mbps) for maximum...
Product Data Sheet
Page 3
ProSAFE® Business 2 x 2 Dual Band Wireless-AC Access Point Data Sheet Product Comparison WAC720 Features WAC720 WAC730 WNDAP660 WNDAP360 Frequency 2.4GHz and 5GHz 2.4GHz and 5GHz 2.4GHz and 5GHz 2.4GHz and 5GHz Wireless Mode (Transmit x Receive) 802.11ac (2x2) 802.11ac .../VLAN Support 16/17 16/17 16/17 16/17 User Interface Yes Yes Yes Yes Browser-based Interface Yes Yes Yes Yes Accepts accessory antennas Yes Yes Yes Yes Easy ceiling mounting/wall mounting Yes Yes Yes Yes Bandwidth management Yes Yes Yes Bonjour Gateway Yes Yes Link Layer Discovery...
ProSAFE® Business 2 x 2 Dual Band Wireless-AC Access Point Data Sheet Product Comparison WAC720 Features WAC720 WAC730 WNDAP660 WNDAP360 Frequency 2.4GHz and 5GHz 2.4GHz and 5GHz 2.4GHz and 5GHz 2.4GHz and 5GHz Wireless Mode (Transmit x Receive) 802.11ac (2x2) 802.11ac .../VLAN Support 16/17 16/17 16/17 16/17 User Interface Yes Yes Yes Yes Browser-based Interface Yes Yes Yes Yes Accepts accessory antennas Yes Yes Yes Yes Easy ceiling mounting/wall mounting Yes Yes Yes Yes Bandwidth management Yes Yes Yes Bonjour Gateway Yes Yes Link Layer Discovery...
Product Data Sheet
Page 4
plug is localized to country of sale • One (1) console port with RJ45 Interface • Two (2) reverse SMA antenna connectors for dual band 2.4 and 5GHz external antennas (not included) • Five (5) LED: Power, Link/ACT, LAN, 2.4GHz, 5GHz Security • WiFi Protected ... adapter (not included): 12V DC, 2.5A; NETGEAR, the NETGEAR logo, ProSUPPORT and ProSAFE are for details. Page 4 of 3 D-WAC720-1 and/or its components may be recycled. Information is valid only if purchased from a NETGEAR authorized reseller. Lifetime technical support includes basic phone ...
plug is localized to country of sale • One (1) console port with RJ45 Interface • Two (2) reverse SMA antenna connectors for dual band 2.4 and 5GHz external antennas (not included) • Five (5) LED: Power, Link/ACT, LAN, 2.4GHz, 5GHz Security • WiFi Protected ... adapter (not included): 12V DC, 2.5A; NETGEAR, the NETGEAR logo, ProSUPPORT and ProSAFE are for details. Page 4 of 3 D-WAC720-1 and/or its components may be recycled. Information is valid only if purchased from a NETGEAR authorized reseller. Lifetime technical support includes basic phone ...