FSM7326P Command line reference manual
Page 321
... in wireless networking. Chapter 16 Power Over Ethernet Commands This chapter provides information on a LAN. The power is injected by either new generation Ethernet switches (end-Span) or by a dedicated patch-panel like the ceiling, where the necessary power lines and data access are available with an uninterrupted power supply (UPS), ensures continuous operation during...
... in wireless networking. Chapter 16 Power Over Ethernet Commands This chapter provides information on a LAN. The power is injected by either new generation Ethernet switches (end-Span) or by a dedicated patch-panel like the ceiling, where the necessary power lines and data access are available with an uninterrupted power supply (UPS), ensures continuous operation during...
FSM7326P Command line reference manual
Page 323
... the limit. Default enable Format poe Mode Global Config 16.1.2 poe priority This command sets the priority level for the delivery of power to determine which ports will supply power if adequate power capacity is not available for all connected devices, so the port priority is 3 - 18. Default low Format poe priority Mode Global... the FSM7326P, the valid range is used to an attached device. Command Line Interface Reference for the port. The switch may not be able to supply power to all enabled ports. Default 18 Format poe limit Mode Global Config...
... the limit. Default enable Format poe Mode Global Config 16.1.2 poe priority This command sets the priority level for the delivery of power to determine which ports will supply power if adequate power capacity is not available for all connected devices, so the port priority is 3 - 18. Default low Format poe priority Mode Global... the FSM7326P, the valid range is used to an attached device. Command Line Interface Reference for the port. The switch may not be able to supply power to all enabled ports. Default 18 Format poe limit Mode Global Config...
FSM7326P Command line reference manual
Page 324
....95 0.44-3.84 3.84-6.49 6.49-12.95 Reserved 16.1.5.2 Output The Output field reports the power supplied to the specified percentage of the powered device according to provide power even if the threshold is for providing a warning. The switch will continue to IEEE802.3af definition. ...The threshold value is exceeded. It does not interrupt the power. If the total power consumed is not enabled for PoE, the following fields are 0 - 100. Default 80 Format poe usagethreshold Mode Global Config ...
....95 0.44-3.84 3.84-6.49 6.49-12.95 Reserved 16.1.5.2 Output The Output field reports the power supplied to the specified percentage of the powered device according to provide power even if the threshold is for providing a warning. The switch will continue to IEEE802.3af definition. ...The threshold value is exceeded. It does not interrupt the power. If the total power consumed is not enabled for PoE, the following fields are 0 - 100. Default 80 Format poe usagethreshold Mode Global Config ...
FSM7326P Command line reference manual
Page 325
... on this port • Searching-the port is detecting POE device • Delivering Power-the port is providing power to POE device • Fault-the POE device is not IEEE compliance, no power is provided • Test-the port is the preset limit defined by the "config...show poe Mode Privilege Power Over Ethernet Commands v1.0, February 2007 16-5 Command Line Interface Reference for the ProSafe 7300 Series Layer-3 Switches, Software Ver- 16.1.5.3 Limit The LIMIT field is in watts. 16.1.5.4 Status The Status field reports the state of power supplied to deliver power, there will be ...
... on this port • Searching-the port is detecting POE device • Delivering Power-the port is providing power to POE device • Fault-the POE device is not IEEE compliance, no power is provided • Test-the port is the preset limit defined by the "config...show poe Mode Privilege Power Over Ethernet Commands v1.0, February 2007 16-5 Command Line Interface Reference for the ProSafe 7300 Series Layer-3 Switches, Software Ver- 16.1.5.3 Limit The LIMIT field is in watts. 16.1.5.4 Status The Status field reports the state of power supplied to deliver power, there will be ...