Instruction Manual
Page 14
... the faceplate will not hit the lid when closing and opening. • If the fuse blows, first make sure the wires aren't touching to the car chassis (ground), you connect the ignition wire to a power source with a constant voltage supply, as shown above. To prevent a short circuit, do not... blinkers, wipers, etc. Number of any metal part in damage to any accessories except for each unit. 3. Connect the wiring harness wires in your car's ignition does not have an ACC position, connect the ignition wires to a front output terminal, do not mix front and rear). wires or ground them...
... the faceplate will not hit the lid when closing and opening. • If the fuse blows, first make sure the wires aren't touching to the car chassis (ground), you connect the ignition wire to a power source with a constant voltage supply, as shown above. To prevent a short circuit, do not... blinkers, wipers, etc. Number of any metal part in damage to any accessories except for each unit. 3. Connect the wiring harness wires in your car's ignition does not have an ACC position, connect the ignition wires to a front output terminal, do not mix front and rear). wires or ground them...
Instruction Manual
Page 15
Connecting Wires to Terminals KENWOOD disc changer control input (KRC-235 only) 2 To connect the Disc changer, consult your Disc changer manual. 3 Rear left speaker 36 To rear right speaker 39 - 15 - P.CONT ANT CONT Power control/Motor antenna control wire (Blue/White) Ignition key switch 10 Car fuse box (Main fuse) 11 Battery 12...
Connecting Wires to Terminals KENWOOD disc changer control input (KRC-235 only) 2 To connect the Disc changer, consult your Disc changer manual. 3 Rear left speaker 36 To rear right speaker 39 - 15 - P.CONT ANT CONT Power control/Motor antenna control wire (Blue/White) Ignition key switch 10 Car fuse box (Main fuse) 11 Battery 12...
Instruction Manual
Page 16
...;5mm 8 mm MAX. 4 ø5mm 8mm MAX. Accessory3...for Nissan car Accessory4 ...for Toyota car • During installation, do not use of the mounting sleeve with the accessory screws. The use any other screw hole than the one specified. Accessory5 .... ■ Screwing the Faceplate on the Unit If you screw it in another hole, it will contact and may skip). ■ Installing in Japanese-Made Cars 1 Refer to the section "Removing the hard rubber frame" (page 17) and then remove the hard rubber frame. 2 Align the holes in the unit (two...
...;5mm 8 mm MAX. 4 ø5mm 8mm MAX. Accessory3...for Nissan car Accessory4 ...for Toyota car • During installation, do not use of the mounting sleeve with the accessory screws. The use any other screw hole than the one specified. Accessory5 .... ■ Screwing the Faceplate on the Unit If you screw it in another hole, it will contact and may skip). ■ Installing in Japanese-Made Cars 1 Refer to the section "Removing the hard rubber frame" (page 17) and then remove the hard rubber frame. 2 Align the holes in the unit (two...
Instruction Manual
Page 18
...misoperation or miswiring. English Troubleshooting Guide What might seem to a different speaker. ? Before calling service, first check the following table for when in the car. ☞ Check the speaker wiring. ✔ The tape head is dirty. ☞ Clean the tape head. ✔ The speakers are not ...not open or close. ✔ The faceplate is not functioning normally. ☞ Press the reset button on "Connecting Wires to Terminals". ✔ The cassette tape is being pinched by a screw in Tuner source. ? The Touch Sensor Tone doesn't sound. ✔ The preout jack is bad. ☞...
...misoperation or miswiring. English Troubleshooting Guide What might seem to a different speaker. ? Before calling service, first check the following table for when in the car. ☞ Check the speaker wiring. ✔ The tape head is dirty. ☞ Clean the tape head. ✔ The speakers are not ...not open or close. ✔ The faceplate is not functioning normally. ☞ Press the reset button on "Connecting Wires to Terminals". ✔ The cassette tape is being pinched by a screw in Tuner source. ? The Touch Sensor Tone doesn't sound. ✔ The preout jack is bad. ☞...
Instruction Manual
Page 19
... Changer source is not ON, with CD recorder. ✔ A non-compatible CD changer is connected. ☞ Connect the supported disc changer. (page 3) ? Radio reception is poor. ✔ The car antenna is not extended. ☞ Pull the antenna out all the way. ✔ The antenna control wire is entered when switching modes. - 19...
... Changer source is not ON, with CD recorder. ✔ A non-compatible CD changer is connected. ☞ Connect the supported disc changer. (page 3) ? Radio reception is poor. ✔ The car antenna is not extended. ☞ Pull the antenna out all the way. ✔ The antenna control wire is entered when switching modes. - 19...
