Instruction Manual
Page 4
...again with a clean soft dry cloth. ¤ • Applying spray cleaner directly to ISO 8859-1 can be inapplicable. 4 | KDC-X994/ KDC-BT945U/ KDC-X794/ KDC-MP745U Refer to explain more clearly how the controls are examples used . If the faceplate is displayed. Lens Fogging When you purchase optional... be displayed. • The RDS feature won't work with your Kenwood dealer. Refer to factory settings when the Reset button is initially set on the display may not allow CDs to operate properly, press the Reset button. In such a situation, remove the disc and wait for the ...
...again with a clean soft dry cloth. ¤ • Applying spray cleaner directly to ISO 8859-1 can be inapplicable. 4 | KDC-X994/ KDC-BT945U/ KDC-X794/ KDC-MP745U Refer to explain more clearly how the controls are examples used . If the faceplate is displayed. Lens Fogging When you purchase optional... be displayed. • The RDS feature won't work with your Kenwood dealer. Refer to factory settings when the Reset button is initially set on the display may not allow CDs to operate properly, press the Reset button. In such a situation, remove the disc and wait for the ...
Instruction Manual
Page 44
Turn the [VOL] knob and press it again briefly. ⁄ • Register 6 patterns of KDC-X994/ KDC-X794 1 Select the source Press the [SRC] button. Speaker Setting (page 42) - Display Item Range "X'Over" "Front" "FC" Front High Pass Filter Through, 30*, 40, 50*, 60, 70... | KDC-X994/ KDC-BT945U/ KDC-X794/ KDC-MP745U Adjust each item. Select "Detailed Setup" > "X'Over". 4 Select the speaker you want to set in the memory Turn the [VOL] knob and press it when the desired item is displayed. Audio Preset Memory Registering the value setup by the Reset button. •...
Turn the [VOL] knob and press it again briefly. ⁄ • Register 6 patterns of KDC-X994/ KDC-X794 1 Select the source Press the [SRC] button. Speaker Setting (page 42) - Display Item Range "X'Over" "Front" "FC" Front High Pass Filter Through, 30*, 40, 50*, 60, 70... | KDC-X994/ KDC-BT945U/ KDC-X794/ KDC-MP745U Adjust each item. Select "Detailed Setup" > "X'Over". 4 Select the speaker you want to set in the memory Turn the [VOL] knob and press it when the desired item is displayed. Audio Preset Memory Registering the value setup by the Reset button. •...
Instruction Manual
Page 46
...Delete mode Turn the [VOL] knob and press it when the desired item is displayed when the operation procedure can be erased by the Reset button. Select "Initial Settings" > "Favorite Delete". 4 Enter Favorite Preset Memory Delete mode Press the [VOL] knob. 5 Select the number.... Cancelling the Favorite Preset Memory mode Press the [FAV] button. ⁄ • Registering the operation procedure to delete Turn the [VOL] knob and press it when the desired item is displayed. 46 | KDC-X994/ KDC-BT945U/ KDC-X794/ KDC-MP745U Select preset number. "Delete?" is displayed. Select "ALL...
...Delete mode Turn the [VOL] knob and press it when the desired item is displayed when the operation procedure can be erased by the Reset button. Select "Initial Settings" > "Favorite Delete". 4 Enter Favorite Preset Memory Delete mode Press the [VOL] knob. 5 Select the number.... Cancelling the Favorite Preset Memory mode Press the [FAV] button. ⁄ • Registering the operation procedure to delete Turn the [VOL] knob and press it when the desired item is displayed. 46 | KDC-X994/ KDC-BT945U/ KDC-X794/ KDC-MP745U Select preset number. "Delete?" is displayed. Select "ALL...
Instruction Manual
Page 69
battery. 8 Press the reset button. 2WARNING If you connect the ignition wire (red) and the battery wire (yellow) to the car chassis (ground), you connect the ignition wire to too ..." is installed, check whether the brake lamps, blinkers, wipers, etc. Therefore, the speaker wire should be displayed may start a fire. of-sight distance of KDC-X994/ KDC-BT945U Installation Procedure 1 To prevent a short circuit, remove the key from the ignition and disconnect the - connector to direct sunlight or excessive heat or humidity...
battery. 8 Press the reset button. 2WARNING If you connect the ignition wire (red) and the battery wire (yellow) to the car chassis (ground), you connect the ignition wire to too ..." is installed, check whether the brake lamps, blinkers, wipers, etc. Therefore, the speaker wire should be displayed may start a fire. of-sight distance of KDC-X994/ KDC-BT945U Installation Procedure 1 To prevent a short circuit, remove the key from the ignition and disconnect the - connector to direct sunlight or excessive heat or humidity...
Instruction Manual
Page 74
...Only the voice of your nearest service center. ERROR 05: The disc is activated. Wire or insulate the speaker cable properly and press the reset button. No beep is heard at a low level. The hands-free talk volume can be registered (pairing). The PIN code is... is heard from this unit. Another Bluetooth device is set ON. ? Close the vehicle windows to USB again. 74 | KDC-X994/ KDC-BT945U/ KDC-X794/ KDC-MP745U The messages shown below display your nearest service center. If the error message is too small, it during hands-free talk. Read ...
...Only the voice of your nearest service center. ERROR 05: The disc is activated. Wire or insulate the speaker cable properly and press the reset button. No beep is heard at a low level. The hands-free talk volume can be registered (pairing). The PIN code is... is heard from this unit. Another Bluetooth device is set ON. ? Close the vehicle windows to USB again. 74 | KDC-X994/ KDC-BT945U/ KDC-X794/ KDC-MP745U The messages shown below display your nearest service center. If the error message is too small, it during hands-free talk. Read ...
Instruction Manual
Page 75
...• T here is no incoming call list. • T here is no phone book list. If this message still appears, press the reset button on again. Pairing Failed: Pairing error. Too Long: The word or utterance is too long to be recognized because of voice tags reaches the...have already been registered. HF Disconnect: The unit cannot communicate with Favorite Control cannot be available. If this message still appears, press the reset button on the selected source or mode. See (page 62) for information on again. Too Soft: Voice is supported. Memory Full: The ...
...• T here is no incoming call list. • T here is no phone book list. If this message still appears, press the reset button on again. Pairing Failed: Pairing error. Too Long: The word or utterance is too long to be recognized because of voice tags reaches the...have already been registered. HF Disconnect: The unit cannot communicate with Favorite Control cannot be available. If this message still appears, press the reset button on the selected source or mode. See (page 62) for information on again. Too Soft: Voice is supported. Memory Full: The ...