Instruction Manual
Page 4
..., press the Reset button. Lens Fogging When you purchase optional accessories, check with your unit If this condensation on the display may not allow CDs to reset your Kenwood dealer to make sure that conform to ISO 8859-1 can be inapplicable. 4 | KDC-X994/ KDC-BT945U/ KDC-X794/ KDC-MP745U If the... unit still does not operate normally after a while, consult your Kenwood dealer. • When you turn on ...
..., press the Reset button. Lens Fogging When you purchase optional accessories, check with your unit If this condensation on the display may not allow CDs to reset your Kenwood dealer to make sure that conform to ISO 8859-1 can be inapplicable. 4 | KDC-X994/ KDC-BT945U/ KDC-X794/ KDC-MP745U If the... unit still does not operate normally after a while, consult your Kenwood dealer. • When you turn on ...
Instruction Manual
Page 44
...in the memory Turn the [VOL] knob and press it again briefly. ⁄ • Register 6 patterns of KDC-X994/ KDC-X794 1 Select the source Press the [SRC] button. "Memory Completed" is displayed. DSP Setup X'Over Setting Fine adjusting the following operations to setup the Sound Control. ... number "1": When you press the Reset, all the sources will be erased by Sound Control. 1 Setup Sound Control Refer to the following setting values corresponding to set in (page 39). 44 | KDC-X994/ KDC-BT945U/ KDC-X794/ KDC-MP745U Select "YES". Press the [VOL] button. 6 Repeat steps 3 to 4...
...in the memory Turn the [VOL] knob and press it again briefly. ⁄ • Register 6 patterns of KDC-X994/ KDC-X794 1 Select the source Press the [SRC] button. "Memory Completed" is displayed. DSP Setup X'Over Setting Fine adjusting the following operations to setup the Sound Control. ... number "1": When you press the Reset, all the sources will be erased by Sound Control. 1 Setup Sound Control Refer to the following setting values corresponding to set in (page 39). 44 | KDC-X994/ KDC-BT945U/ KDC-X794/ KDC-MP745U Select "YES". Press the [VOL] button. 6 Repeat steps 3 to 4...
Instruction Manual
Page 46
... [VOL] knob and press it when the desired item is displayed when the operation procedure can be erased by the Reset button. The memory cannot be registered. Select the "STANDBY" display. ✍✍SRC Select mode 2: Pressing the [SRC...is displayed. Cancelling the Favorite Preset Memory mode Press the [FAV] button. ⁄ • Registering the operation procedure to recall in the first hierarchy can be automatically played. " FAV " is displayed. 46 | KDC-X994/ KDC-BT945U/ KDC-X794/ KDC-MP745U Menu list Setting Menu list Setting item Audio control Audio control ...
... [VOL] knob and press it when the desired item is displayed when the operation procedure can be erased by the Reset button. The memory cannot be registered. Select the "STANDBY" display. ✍✍SRC Select mode 2: Pressing the [SRC...is displayed. Cancelling the Favorite Preset Memory mode Press the [FAV] button. ⁄ • Registering the operation procedure to recall in the first hierarchy can be automatically played. " FAV " is displayed. 46 | KDC-X994/ KDC-BT945U/ KDC-X794/ KDC-MP745U Menu list Setting Menu list Setting item Audio control Audio control ...
Instruction Manual
Page 69
... to a rear output terminal. • After the unit is an obstacle between this unit and the cell-phone. of-sight distance of KDC-X994/ KDC-BT945U Installation Procedure 1 To prevent a short circuit, remove the key from the ignition and disconnect the - The above maximum communication range ...the old fuse with one with the same rating. • Insulate unconnected wires with communication due to which they correspond. battery. 8 Press the reset button. 2WARNING If you connect the ignition wire (red) and the battery wire (yellow) to the car chassis (ground), you could damage the ...
... to a rear output terminal. • After the unit is an obstacle between this unit and the cell-phone. of-sight distance of KDC-X994/ KDC-BT945U Installation Procedure 1 To prevent a short circuit, remove the key from the ignition and disconnect the - The above maximum communication range ...the old fuse with one with the same rating. • Insulate unconnected wires with communication due to which they correspond. battery. 8 Press the reset button. 2WARNING If you connect the ignition wire (red) and the battery wire (yellow) to the car chassis (ground), you could damage the ...
Instruction Manual
Page 74
...Error: The unit is too small, it during hands-free talk. Or the unit is heard depending on the unit. And then press the reset button on the type of an incoming call. No beep is malfunctioning for some reason. Check the disc magazine. Bluetooth audio source...Manual, try "0000". ? CD-IN (Blink): The CD player section is played with reference to (page 50) to USB again. 74 | KDC-X994/ KDC-BT945U/ KDC-X794/ KDC-MP745U Unsupported File: An Audio file is not operating properly. Reinsert the CD. No Device: The USB device is selected as a ...
...Error: The unit is too small, it during hands-free talk. Or the unit is heard depending on the unit. And then press the reset button on the type of an incoming call. No beep is malfunctioning for some reason. Check the disc magazine. Bluetooth audio source...Manual, try "0000". ? CD-IN (Blink): The CD player section is played with reference to (page 50) to USB again. 74 | KDC-X994/ KDC-BT945U/ KDC-X794/ KDC-MP745U Unsupported File: An Audio file is not operating properly. Reinsert the CD. No Device: The USB device is selected as a ...
Instruction Manual
Page 75
... the control unit. No Entry: The cell-phone has not been registered (pairing). If this message still appears, press the reset button on supported iPods. If this message still appears, press the reset button on again. Err No Matching: The voice tag is repeated, use another USB device. If the same display is wrong...
... the control unit. No Entry: The cell-phone has not been registered (pairing). If this message still appears, press the reset button on supported iPods. If this message still appears, press the reset button on again. Err No Matching: The voice tag is repeated, use another USB device. If the same display is wrong...