IBM 86626RY - Netfinity 5500 M20 Support and Manuals
Get Help and Manuals for this IBM item
Popular IBM 86626RY Manual Pages
Hardware Maintenance Manual - Page 9
... security 25 Using the power-on self-test (POST 11 POST beep codes 12 Error messages - Type 8662
General checkout 8 Diagnostic tools 11
Diagnostic programs 11 Power-on password menu . . . 26 Using the Administrator Password menu . 28 Start options 29 Advanced setup 29 Core chip set control 29 Cache control 29 PCI bus control 30 Memory...
Hardware Maintenance Manual - Page 23
... view the error messages in the Test Log. Turn on the diagnostic programs:
1. If the server is , a diskette which has no contents that a keyboard and mouse are attached to the server. If a power-on password or administrator password is set , you cannot run because the relevant device is either not installed or is set , the server...
Hardware Maintenance Manual - Page 34
... delete both the administrator and power-on passwords, and allow a power-on password prompt; You must enter a password each time that you forget the power-on password, and the administrator password has been set
Power-on password only
Administrator password only
Administrator and power-on the Configuration/Setup Utility main menu. Administrator password provides access to complete the system...
Hardware Maintenance Manual - Page 35
... for unattended boot with password data field must be set , you enter the password. then, press Enter.
Select Allow for details.) Start the Configuration/Setup Utility program and change the position of the following methods:
If an administrator password has been set :
1. When a power-on Password menu appears. 2. Press Enter to support locally or remotely scheduled system...
Hardware Maintenance Manual - Page 40
... might be sure that came with it. Install the adapter in the server. Install software programs. See the installation instructions that they contain the correct information. Restore settings:
After you want to configure the server.
1. Exit setup:
Select to delete the changes and restore the previous settings. Configuring options
Before installing a new device or program, read the...
Hardware Maintenance Manual - Page 43
..., you must manually override the settings to obtain a full-duplex connection. However, except for additional information. The Ethernet controller provides 10BASE-T and 100BASE-TX support through the RJ-45 connector on the network and then sets the controller to operate at a data rate of the server.
In this device driver. Use ServerGuide to install this case...
Hardware Maintenance Manual - Page 44
...specifications
The Ethernet controller on the system board provides 10BASE-T and 100BASE-TX support through the RJ-45 connector on a standard Ethernet system can be sure to set... install the adapter. and protocols that the server supports. When you install the device drivers and.... Notes
The Ethernet controller supports the operating systems that are installing an IBM 10/100 Ethernet adapter, ...
Hardware Maintenance Manual - Page 45
...specifications.../TIA-568 Category 5.
Table 1 on page 38 describes the specifications for UTP cables used for use a UTP cable that is ... the network and then sets the controller to operate at both ends. The Ethernet controller supports the auto-detection mode only... thicker than telephone extension cables. When you install the device drivers and configure the Ethernet controller for 10BASE-T ...
Hardware Maintenance Manual - Page 89
... parameter. Vendor shows characters that PFA errors were not found. No indicates that represent the drive manufacturer. Netfinity 5500 M20 - Battery Backup Write Cache shows the current setting, Enabled or Disabled, for the drive. The valid settings in the Shared state are 201 through 215. When you select a specific hot-spare drive from the Main...
Hardware Maintenance Manual - Page 90
... or model number ...part of an array. Channel Information Panel
When you should plan to replace the device. SCSI Transfer Speed shows the current SCSI transfer setting (Optimal, Ultra2 SCSI, UltraSCSI, Fast SCSI 2, or SCSI 2) for more information. Drive Firmware...the physical drive. PFA Error indicates the status, Yes or No, for the drive. When you select a specific physical drive from the...
Hardware Maintenance Manual - Page 124
... error.
Rebuild Rate
The current setting ...Code Block Version The current version number of defunct hard
disk drives. Defunct Disk Count The current number of the
firmware loaded on the appropriate adapter or controller to 8). Configuration Update...supported. indicates that it active.
Concurrent Commands The maximum number of the
battery-backup cache (installed, not
installed...
Hardware Maintenance Manual - Page 142
... to "Starting the ServeRAID Administration and Monitoring Program" on page 146
Installing ServerRAID device drivers for Windows NT:
This section provides two sets of instructions for Windows NT, NetWare, OS/2, OpenServer, and UnixWare. To install the ServeRAID WIN32-Based program:
1. Refer to install the ServeRAID device drivers for OS/2 and NetWare. The OS/2 and NetWare Administration and...
Hardware Maintenance Manual - Page 173
..., set the resources that specific server resource. From the Select family field, select Netfinity 5500 M20. Select Downloadable files. Failure to the server. If you can install a new adapter without turning off the power to remove a hot-plug adapter, reverse the steps.
Type 8662 165 To obtain the operating system hot-plug PCI support code, access...
Hardware Maintenance Manual - Page 293
... POST error codes and messages on page 8. Type 8662 servers. Once the configuration has reset to the default, it must be saved in CMOS. 3. Type 8662 285 Configuration problems can be stored in Setup to be loaded by index, refer to have available when servicing the computer.
Use this Symptom-to-FRU Index to help you replace...
Hardware Maintenance Manual - Page 322
...codes identify the controller state.
For jumper locations, see the Hardware Maintenance Manual for the system you solve ServeRAID problems when servicing the computer. If the error persists, replace ServeRAID controller.
7XXX thru 8XXX (Host/Local PCI Bus Interface Error) 1. EF10 (Default ISPR) 1. If the error persists, replace ServeRAID controller.
6XXX (Cache DRAM Error) 1. Install...
IBM 86626RY Reviews
We have not received any reviews for IBM yet.