IBM 86613RY - Netfinity 5500 M10 Support and Manuals
Popular IBM 86613RY Manual Pages
Setup Guide - Page 4
... could include technical inaccuracies or typographical errors. All rights reserved. Government Users - This publication was developed for technical information about , IBM products (machines and programs), programming, or services that IBM intends to you. Documentation related to restrictions set forth in GSA ADP Schedule Contract with IBM Corp.
IBM may be sure to the information...
Setup Guide - Page 5
... 14
© Copyright IBM Corp. 1998
1 Express Setup and Installation
This setup and installation section contains the information that will guide you through:
Setting up and cabling your Network Operating System (NOS). Installing an Additional Microprocessor 7 4. Installing Additional Options 12 Software Installation 13 1. Installing the NetBAY3 (Tower Models Only 6 2. Cabling Your...
Setup Guide - Page 8
5
32 kg (70.5 lbs)
55 kg (121.2 lbs)
CAUTION: Use safe lifting practices when lifting your machine.
4 Netfinity 5500 M10 Express Setup and Installation
Setup Guide - Page 9
....
Before you might want to set up your server hardware is easily accessible, you begin installing options. RAID level-0 requires one drive (minimum), RAID level-1 requires two drives (minimum), and RAID level-5 requires three drives (minimum). Express Setup and Installation 5 To maintain proper system cooling, do not operate the Netfinity 5500 M10 for more information...
Setup Guide - Page 10
... of the bezel around the posts on page 7.
6 Netfinity 5500 M10 Express Setup and Installation Installing the NetBAY3 (Tower Models Only)
The NetBAY3 is shipped, unattached, inside the NetBAY3. 2 Remove and unpack the bezel. 3 Hook the tabs on the left side of Netfinity 5500 M10 tower models. The bezel for the NetBAY3 is attached to the "NetBAY3...
Setup Guide - Page 11
... Your Server" on page 8. For installation instructions, refer to the "Microprocessor Installation" information in the open position (perpendicular...Server Library and the information provided with "4. Express Setup and Installation 7 Ensure that the tray handle 3 on the server; then,... to the
following procedure to install hot-swap hard disk drives in your Netfinity 5500 M10.
1 Touch the static...
Setup Guide - Page 12
... To connect the server 10BASE-T or 100BASE-TX port to your Netfinity 5500 M10.
1 Select a location that is installed on the power cord, the server must be plugged into a power source...instead of cable
connectors, refer the illustrations on page 10.
8 Netfinity 5500 M10 Express Setup and Installation Cabling Your Server
Use the following page. An EIA/TIA-568 category 5 cable must ...
Setup Guide - Page 13
... supply 1 power connector 13 Management C connector 14 Universal serial bus (USB) 2 15 Universal serial bus (USB) 1 16 Power supply 1 17 Keyboard 18 Ethernet
Mouse
Express Setup and Installation 9
Setup Guide - Page 14
... beep, or your monitor screen is operating properly.
1 Turn on page 12.
10 Netfinity 5500 M10 Express Setup and Installation Important The following procedure to verify that power is present. Start the Configuration/Setup Utility program and select Save Settings. 5. Wait 20 seconds after plugging the power cord into an outlet and before pressing the...
Setup Guide - Page 15
...1
2
100 LINK TX MB OK RX
1 System power light 2 System POST complete light 3 SCSI hard disk drive activity light 4 System error light 5 Processor 2 activity light 6 Ethernet activity light 7 Ethernet link status light 17 Ethernet speed 100 Mbps light 18 Processor 1 activity light... button 14 Diskette drive in-use light 15 Reset button 16 Power control button
Express Setup and Installation 11
Setup Guide - Page 16
... network operating system (NOS) and it is starting without errors, install the additional network adapters one at this time. Start the Configuration/Setup Utility program and select Save Settings. After you have installed all adapters at once, but installing the adapters one at a time. You can change the configuration information in the "Hardware Information" section of...
Setup Guide - Page 17
... the
online instructions to configure hardware, install device drivers, and install the network operating system (NOS).
1. Enhancing Server Performance with the ServeRAID option.
2 To install your NOS installation. 4 From the Main Menu, click on README to see the "ServerGuide and Netfinity Manager Information" section of the NOS CD is required. Express Setup and Installation 13 Before...
Setup Guide - Page 18
... the server hardware, and you must have system-specific NOS installation instructions and device drivers.
To install updates, refer to download updates from the World Wide Web at: http://www.pc.ibm.com/support
1 Click on IBM Servers Support. 2 From the select family field, click on Netfinity 5500 M10. 3 From the list in the Netfinity 5500 M10 window, click on the root directory...
IBM 86613RY Reviews
Do you have an experience with the IBM 86613RY that you would like to share?
Earn 750 points for your review!
We have not received any reviews for IBM yet.
Earn 750 points for your review!