IBM 86624RY - Netfinity 5500 M20 Support and Manuals
Get Help and Manuals for this IBM item
Popular IBM 86624RY Manual Pages
Maintenance Manual - Page 9
...System error log 31 Save settings 32 Restore settings 32 Load default settings 32 Exit setup 32 Configuring options 32 Configuring ISA and PCI adapters 33 Resolving configuration conflicts 33 Resolving hardware configuration conflicts . . 34 Resolving software configuration conflicts . . 34 Configuring the ethernet controller 35 Ethernet cable specifications 36
© Copyright IBM Corp...
Maintenance Manual - Page 23
... testing and you must enter the administrator password to run because the relevant device is either not installed or is unable to the server.
Check the System Error Log for Diagnostics appears, press F2. Type in the appropriate password; Type 8662 15
For system board tests, first remove all installed adapters.
2. then, press Enter.
If the...
Maintenance Manual - Page 34
... power-on the Configuration/Setup Utility main menu. Type the password in a secure place. 3. Select Power-on Password data field. Type of Password No password set
Power-on password only
Administrator password only
Administrator and power-on Password Again data field and type the password again.
Move the cursor to the Enter Power-on password
Results
No password required to all choices...
Maintenance Manual - Page 35
... window appears. Select Allow for details.) Start the Configuration/Setup Utility program and change the position of the following methods:
If an administrator password has been set , POST does not complete until you can remove the battery as described in "Battery replacement" on Password from the System Security menu; then, press Enter. To allow the...
Maintenance Manual - Page 40
.... Reading the instructions helps you to determine the steps that might be required to configure the server.
1.
The following list provides a preview of the actions that are required for installation and configuration. See "Configuration/Setup Utility program" on page 33.
32 Netfinity Server HMM If the information is correct, select Save Settings to save...
Maintenance Manual - Page 43
... full-duplex mode, you must manually override the settings to address the Ethernet controller. You must be selected. Use ServerGuide to install this case, if you connect the server to the ServerGuide package for instructions on the system board. However, except for additional information.
In this device driver. Applications
Netfinity 5500 M20 - The best way to...
Maintenance Manual - Page 44
... Server HMM Notes
The Ethernet controller supports the operating systems that are installing an IBM 10/100 Ethernet adapter, be sure...set any jumpers or configure the controller for any additional configuration requirements. A cost-effective solution to a server is therefore a Plug and Play device. The Ethernet controller supports the auto-detection mode only. Ethernet cable specifications...
Maintenance Manual - Page 45
.... Type 8662 37 Attention The 10BASE-T Ethernet and the 100BASE-TX Fast Ethernet cabling in those cables are rounder and thicker than telephone extension cables.
The following information describes the specifications for 10BASE-T and 100BASE-TX. However, all devices connected to a repeater.
The Ethernet controller supports the auto-detection mode only. Netfinity 5500 M20...
Maintenance Manual - Page 89
..., this parameter. Write-Cache Mode shows the current setting, write through 215.
Product or Model Number shows characters that you select a specific hot-spare drive from the Main Tree, information about the total number of a cluster. Valid settings in the Non-Shared state are 1 through 8.
PFA Error indicates the status, Yes or No, for the...
Maintenance Manual - Page 90
... or Tape drive. Drive Firmware Level shows the current level...errors were not found.
Product or Model Number shows characters that might appear in this field. Logical drive state descriptions:
The following information appears in the Main Panel on page 83 for descriptions of the drive, in use for the drive. When you select a specific...the physical drive is part of microcode in MB,...
Maintenance Manual - Page 124
... Update Count The number of the Administration and Monitoring Program.
indicates that appears on the screen are as follows:
Adapter Number
The active adapter or controller (1
to 8). The adapter or controller
chooses the recovery method when
there is a
ServeRAID startup error.
Rebuild Rate
The current setting (Low, Medium,
or High) of
concurrent commands supported...
Maintenance Manual - Page 142
... provides two sets of instructions for installing the ServeRAID device driver: one that appear on the screen to "Starting the ServeRAID Administration and Monitoring Program" on the system and allow Windows NT or Windows 95 to start.
2.
Insert the IBM ServeRAID Administration and Monitoring Diskette into the diskette drive.
3. then, type the following:
a:\setup
Note
The...
Maintenance Manual - Page 173
... documentation that specific server resource. Netfinity 5500 M20 - If you can result in the Netfinity 5500 M20 indicates hot-plug components. Once Plug and Play detects that a resource is not available, it will manually configure the ISA legacy adapter to the server. To obtain the operating system hot-plug PCI support code, access the IBM Web site...
Maintenance Manual - Page 293
.... 3. The Symptom-to have available when servicing the computer. The POST BIOS displaying POST error codes and messages on page 8. Type 8662 servers. Always start with "General checkout" on the screen. Type 8662 285 Configuration problems can be stored in Setup to be loaded by index, refer to -FRU index
This index supports Netfinity 5500 M20 - The most likely cause...
Maintenance Manual - Page 322
... in the recommended Actions in an error code list that appears in "Symptom-to a SCSI backplane, see "System board jumpers" on page 285. For jumper locations, see the Hardware Maintenance Manual for the system you solve ServeRAID problems when servicing the computer. If the error persists, replace ServeRAID controller.
6XXX (Cache DRAM Error) 1. Install two download jumpers parallel to the...
IBM 86624RY Reviews
We have not received any reviews for IBM yet.