Workstation x4000 Bios Update

ATI Fire GL 2 graphics card users guide

Page 41
... If you do not have this option. ♦ Some older ISA legacy add-in the ESCD (extended system configuration data) area of the system BIOS. Resolving Interrupt Conflicts To support the special graphics processor on card that causes the conflict. Please refer to your Fire GL2 uses the following : &#... add the required legacy card resources to the AGP slot where the card is used for an updated BIOS that has this option and your graphics card does not receive an interrupt, contact your system BIOS setup for an option that says "Assign IRQ to ensure that the I /O: 3B0-3DF Memory Addresses...

ATI Fire GL 4 graphics card users guide

Page 50
... the graphics board are not configured in cards (with jumpers, non-PnP) may be problems if your system BIOS setup for an option that says "Assign IRQ to VGA" or something similar and ensure that this option. Please... to your Fire GL4. Resolving Interrupt Conflicts To support the special graphics processor on the Fire GL4 the system BIOS should automatically assign a system interrupt to modify the I/O address of the add-on using the ISA Configuration Utility...card does not receive an interrupt, contact your motherboard manufacturer for an updated BIOS that has this option is enabled.

hp workstation x4000 - accessory installation guide

Page 47
...of the heatsink should release it from the system board. Remove the Workstation's cover (see page 32). 7. Remove the MEC card (see page 15). 3. CAUTION CAUTION Installing Accessories Processor Processor The x4000 Workstation can have two processors. If you must be very hot. If ...your processor turbo cooler fan is located at www.hp.com/workstations/support. Be very careful when removing the heatsink. The processors must update the BIOS. Disconnect all power cables and any LAN or telecommunications cables. 2. Place the Workstation on its side for 3 to detach the heatsink....

hp workstation x4000 - service handbook

Page 3
HP x4000 Parts Information x4000 Parts and Part Numbers 22 Documentation 26 Software and Training CDs 27 3 Accessory Ordering Information Supported Accessories 18 Mass Storage Device Guide Rails 20 3. Contents 1. HP x4000 Service Information Overview 6 x4000 System Board 7 System Board Switches 8 BIOS Identification 9 Upgrading Memory 10 Replacing or Upgrading a Processor 13 Removing a Processor 13 Installing a Processor 14 Updating Your Operating System 16 2.

hp workstation x4000 - service handbook

Page 13
... update your current processor, you must be very hot. The latest BIOS is not operating, the heatsink may be identical. Disconnect all power cables and any LAN or telecommunications cables. 2. Remove the Chassis Beam Assembly. 6. Be very careful when removing the heatsink. Turn off the display and shut down the Workstation. CAUTION CAUTION HP x4000...

hp workstation x4000 - Technical Reference manual - Windows and Linux (A6068-IE001 E0601)

Page 4
... Resources Overview 44 System BIOS 45 BIOS Identiﬁcation 45 Updating the System BIOS and Firmware 46 Restoring BIOS Default Settings 46 Clearing the CMOS 46 Recovering the BIOS from the Boot Block 47 HP Setup Program 49 Starting the HP Setup Program 49 Main Menu 51 Advanced Menu 52 Security Menu 55 IPMI Menu 56 Power...

hp workstation x4000 - Technical Reference manual - Windows and Linux (A6068-IE001 E0601)

Page 46
... F9 to load the default settings from HP's Web site at www.hp.com/workstations/support Instructions for the HP x4000 workstations from the Setup program. 3. CAUTION NOTE System BIOS and Resources System BIOS Updating the System BIOS and Firmware You can download the latest system BIOS and ﬁrmware for downloading and updating the BIOS and ﬁrmware are posted on page...

hp workstation x4000 - Technical Reference manual - Windows and Linux (A6068-IE001 E0601)

Page 47
...appears: "Configuration has been cleared, switch "Clear Configuration" to power down.) 6. Turn off the Workstation, disconnect the power cord and display cables, and remove the cover. (You must press the power...how to recover the BIOS from the Boot Block If you can't ue the standard BIOS ﬂash, the BIOS could be able to download the system BIOS, see "Updating the System BIOS and Firmware" on ... to ON. Replace the cover, and reconnect the power cord and display cable. 4. See "Starting the HP Setup Program" on page 46. 3. Turn on the ﬂoppy disk.) 4. Exit Setup and save ...

hp workstation x4000 - Technical Reference manual - Windows and Linux (A6068-IE001 E0601)

Page 79
...ﬁguration Tokens Some CMOS tokens are two separate ﬂash update utilities: one to update the BIOS ﬂash device, and another to prevent the user from pressing the power button or the reset button at www.hp.com/workstations/support. The BIOS and ﬁrmware ﬂash utilities utilities are packaged together in process...

hp workstation x4000 - Technical Reference manual - Windows and Linux (A6068-IE001 E0601)

Page 177
..., you must update the BIOS. Open the hard disk drive cage (see page 162). 7. Chapter 10 175 Remove the Workstation's cover (see "Updating Your Operating System" on the Workstation and let it easier to 5 minutes. If your operating system (see page 145). 3. Under normal circumstances, the turbo cooler fan is located at www.hp.com/workstations/support...

hp workstation x4000 - Technical Reference manual - Windows and Linux (A6068-IE001 E0601)

Page 190
The latest BIOS and ﬁrmware for your BIOS. After installing the system board, you need to update your Workstation are available from: www.hp.com/workstations/support. 188 Chapter 10 Connect all the power and telecommunications cables. 17. NOTE Installing or Replacing Parts and Accessories System Board 15. Replace the Workstation's cover and bezel as described in "Cover and Front Bezel" on page 145. 16.

hp workstation x4000 - Technical Reference manual - Windows and Linux (A6068-IE001 E0601)

Page 230
You must also re-install the drivers for these accessories. NOTE NOTE Troubleshooting Recovering or Reconﬁguring Windows 2000 or Windows NT The full recovery function restores a factory disk image of your computer. We recommended you have accessories that were saved before performing the full recovery also need to be restored. 230 Chapter 11 All data ﬁles and software applications that you removed, replace them now. If you install updated drivers, BIOS, and ﬁrmware available from www.hp.com/workstations/support.

hp workstation x4000 - Technical Reference manual - Windows and Linux (A6068-IE001 E0601)

Page 232
... problems on your Workstation, including: • Technical notes and white papers • Documentation for your Workstation (described on the following page) • BIOS updates (including the upgrade utility and instructions) • The latest drivers and software utilities including e-diagtools, updates for the utility partition, and HP TopTools HP's support web site is www.hp.com/workstations/support. 232 Chapter...

Workstation x4000 Bios Update - HP