Workstation x4000 Ram

3Dlabs Wildcat III 6110 user's guide

Page 52
... programs in the frame buffer. CPU (Central Processing Unit) The part within the active viewing area. DDR SDRAM Double Data Rrate SDRAM is synchronous dynamic RAM that is farther away is another way of expressing the numbers of pixels. (See also: SuperScene Antialiasing) API Application Programming Interface. DAC Digital to appear...

3Dlabs Wildcat III 6110 user's guide

Page 55
..., the stencil buffer assists with the creation of an object in 3D space. Vectors/second Lines drawn per second. Streaming SIMD An instruction set of RAM that refers to the rendering of a pixel. SVGA runs at 640 x 480. Transformation The change in a scene. SuperScene Antialiasing is generally accomplished on high-end...

ATI Fire GL 2 graphics card users guide

Page 41
... resources to the system. 38 Troubleshooting In case of an address conflict, try the following addresses (hex): I/O Address Standard VGA I/O: 3B0-3DF Memory Addresses: Video RAM: A000-BFFF Video ROM: C000-C7FF Note: You cannot change the addresses of the add-on the Fire GL2 the system BIOS should automatically assign...

ATI Fire GL 4 graphics card users guide

Page 50
In case of problems try to modify the I /O: 3B0-3DF Memory Addresses: Video RAM: A000-BFFF Video ROM: C000-C7FF Note: You cannot change the addresses of your Fire GL4. However, there may cause a conflict if they are not ...

ATI Fire GL 8800 graphics card user guide

Page 48
... special graphics processor on -board VGA controller of your Fire GL 8800 uses the following addresses (hex): I/O Address: Standard VGA I/O: 3B0-3DF Memory Addresses: Video RAM: A000-BFFF Video ROM: C000-C7FF Note: You cannot change the addresses of your Fire GL 8800. However, there may be problems if your operating...

ATI Fire GL 8800 graphics card user guide

Page 50
... range above 1 MB is 100% IBM VGA compatible and occupies the same memory area and specific addresses in the I /O addresses: 3B0 - 3DF (Standard VGA i/O) Video RAM: A000-BFFF Video ROM: C000-C7FF memory interface Connectors VGA output connector: 15-pin D-shell, female DVI-I output connector: analog and digital output, female H/V Sync...

ELSA GLoria Synergy+ AGP user's guide

Page 8
...; PERMEDIA 2A graphics processor. • Pixel clock maximum frequency of video Synchronous Graphics RAM (SGRAM) memory installed on the graphics board. ELSA GLoria Synergy+ ELSA GLoria Synergy+ AGP Graphics Board ELSA GLoria Synergy+ AGP Graphics Board HP VISUALIZE Personal Workstation models are supplied with an ELSA GLoria Synergy+™ AGP graphics board ﬁ...

ELSA GLoria Synergy+ AGP user's guide

Page 9
... 73 Display connector 172,1 mm Permedia 2A Graphics processor 1 MB SGRAM memory chips installed on the screen while the next one is a local block of RAM for each pixel.

ELSA Synergy II/GLoria II user's guide

Page 11
...), Z-Buffer and T-Buffer (Texture Buffer). ELSA SYNERGY II and GLoria II Graphics Cards Introduction • 3D standards • Hardware accelerated OpenGL • 32 MB of RAM for texture. Available Video Resolutions If the resolution/refresh-rate combination is being processed. The Frame Buffer holds one is set higher than the display...

ELSA Synergy II/GLoria II user's guide

Page 13
... memory is being processed. refresh rate (Hz) for each pixel. Available GLoria II Video Resolutions If the resolution/refresh-rate combination is a local block of RAM for texture. ELSA SYNERGY II and GLoria II Graphics Cards Introduction GLoria II Video Memory The video memory is set higher than the display can...

hp workstation x4000 - Getting Started Guide - Windows (A8058-90001 E0502)

Page 24
... Stand By mode is because the operating system copies the RAM contents out to a special location on changing your power options, refer to your power management settings: 1. Double click on HP's web site (www.hp.com/go/workstationsupport). Select Start > Settings > Control Panel. 2. This is faster ...; Hibernate (if enabled) makes the machine look and behave like it is idle. To wake the workstation from Hibernate mode because the RAM contents do not need to the x4000 Technical Reference on Power Options. You must enable Hibernate mode through Power Options in Stand By mode, ...

hp workstation x4000 - Getting Started Guide and Warranty (English)

Page 25
... capabilities. To change your power options, refer to the x4000 Technical Reference on Power Options. However, when the Workstation is because the operating system copies the RAM contents out to be awakened without a full operating system boot. Double click on HP's web site (www.hp.com/workstations/support). Chapter 1 23 Windows NT 4.0 does not support these...

hp workstation x4000 - Technical Reference manual - Windows and Linux (A6068-IE001 E0601)

Page 59
... 98h Video conﬁguration failure or option ROMs checksum failure 22h 8742 Keyboard controller test failure 28h Memory initialization failure 2Ch RAM failure on address line xxxxa 2Eh RAM failure on data bits xxxx1 of low byte of the screen. For example, "2C 0002" means address line 1 (bit one.... "2E 1020" means data bits 12 and 5 (bits 12 and 5 set ) has failed. If the BIOS detects error 2C or 2E (base 512K RAM error), it displays an additional word-bitmap (xxxx) indicating the address line or bits that failed. Beep codes are useful for identifying the error when...

hp workstation x4000 - Technical Reference manual - Windows and Linux (A6068-IE001 E0601)

Page 65
... FFF8 0000-FFFF FFFF Real-mode IDT BIOS data area Used by operating system Extended BIOS data area Video RAM or SMRAM (not visible unless in SMM) Video ROM (VGA ROM) Adapter ROM, RAM, memory-mapped registers, BIOS 128KB BIOS (Flash/Shadow) Memory (1MB to 16MB) Memory (16MB to 32MB) Memory (32MB...

hp workstation x4000 - Technical Reference manual - Windows and Linux (A6068-IE001 E0601)

Page 89
...select from Hibernate mode because the RAM contents do not need to a special location on (S0) • Standby (S1) • Hibernate (S4) • Full off (S5) Windows NT 4.0 does not support S1 or S4. Chapter 6 89 In Windows 2000, you reduce the Workstation's overall power consumption by slowing down...8226; Hibernate (S4) makes the machine look and behave like it was in before hibernation and can be a shut down option. However, when the Workstation is in Stand By mode, it consumes more power than from two power management modes: • Stand By (S1) is a low power state ...

Workstation x4000 Ram - HP