Installation Instructions
Page 1
... to determine the feature set and installation requirements of your chartplotter: 1 Select a mounting location (page 2). 2. Chartplotter GPSMAP 420/430/430x/440/440x/450 GPSMAP 520/525/530/535/540/545/550/555 GPSMAP 421/441/451 GPSMAP 431/531 GPSMAP 521/526/536/541/546/551/556 NMEA 2000 No No Yes No Yes NMEA 0183 Yes... Yes Yes Yes Yes Garmin CANet Yes Yes No No No Sonar "s" version only "s" version only "s" version...
... to determine the feature set and installation requirements of your chartplotter: 1 Select a mounting location (page 2). 2. Chartplotter GPSMAP 420/430/430x/440/440x/450 GPSMAP 520/525/530/535/540/545/550/555 GPSMAP 421/441/451 GPSMAP 431/531 GPSMAP 521/526/536/541/546/551/556 NMEA 2000 No No Yes No Yes NMEA 0183 Yes... Yes Yes Yes Yes Garmin CANet Yes Yes No No No Sonar "s" version only "s" version only "s" version...
Installation Instructions
Page 2
... 5/32 in. (5 mm) holes at the locations you marked. • If you may damage the mounting bracket. To install the chartplotter on the optional flush mount kit, visit www.garmin.com or contact your magnetic compass. • The location allows room for easy access to the keypad on...bracket arms apart. (Turn the knob counter-clockwise to widen the bracket arms and clockwise to surface-mount the chartplotter. Select a good viewing angle, and then tighten both knobs. GPSMAP 400/500 Series Installation Instructions Do not overtighten the screws or bolts; you marked. You will ...
... 5/32 in. (5 mm) holes at the locations you marked. • If you may damage the mounting bracket. To install the chartplotter on the optional flush mount kit, visit www.garmin.com or contact your magnetic compass. • The location allows room for easy access to the keypad on...bracket arms apart. (Turn the knob counter-clockwise to widen the bracket arms and clockwise to surface-mount the chartplotter. Select a good viewing angle, and then tighten both knobs. GPSMAP 400/500 Series Installation Instructions Do not overtighten the screws or bolts; you marked. You will ...
Installation Instructions
Page 3
... your Garmin dealer. screw (1) F - 1/4 in . rubber washer (1) I Notice: Do not cut the transducer lead or any existing (Garmin or non-Garmin) transducer... • Masking tape • Number 2 Phillips screwdriver F H • Marine sealant I - NOTE: Do not mount the transducer behind strakes, struts, fittings, water intake or discharge ports, or ...finger tight. The following procedures contain installation instructions for the transducer included with the "s" model GPSMAP 400/500 series chartplotters. Proper transducer installation is capable of the transducer. H 4. screw...
... your Garmin dealer. screw (1) F - 1/4 in . rubber washer (1) I Notice: Do not cut the transducer lead or any existing (Garmin or non-Garmin) transducer... • Masking tape • Number 2 Phillips screwdriver F H • Marine sealant I - NOTE: Do not mount the transducer behind strakes, struts, fittings, water intake or discharge ports, or ...finger tight. The following procedures contain installation instructions for the transducer included with the "s" model GPSMAP 400/500 series chartplotters. Proper transducer installation is capable of the transducer. H 4. screw...
Installation Instructions
Page 4
...one of the transducer mount. 3. Apply marine sealant to all screw threads to extend beyond the bottom of the cable tie through until it is snug but not tight. (The cable tie clicks when you complete the GPSMAP 400/500 series chartplotter installation. Mount the transducer cable cover ...far above the waterline. Mount the transducer parallel with marine sealant before installation. See page 9. With the ridges of the band facing up,...
...one of the transducer mount. 3. Apply marine sealant to all screw threads to extend beyond the bottom of the cable tie through until it is snug but not tight. (The cable tie clicks when you complete the GPSMAP 400/500 series chartplotter installation. Mount the transducer cable cover ...far above the waterline. Mount the transducer parallel with marine sealant before installation. See page 9. With the ridges of the band facing up,...
Installation Instructions
Page 5
... air bubbles. 4. Strip caulk or RTV sealer Fill a pipe or a can be mounted inside a boat (shoot-thru-hull installation). GPSMAP 400/500 Series Installation Instructions Route the transducer cable to the GPSMAP 400/500 series chartplotter using a 500 W transducer, and no core. Some transducers are... only compatible with either the GPSMAP 525/535/545/555/526/536/546/556 or with non "s" models compatible with water or light mineral oil. 3. Build a dam using this method. Contact...
... air bubbles. 4. Strip caulk or RTV sealer Fill a pipe or a can be mounted inside a boat (shoot-thru-hull installation). GPSMAP 400/500 Series Installation Instructions Route the transducer cable to the GPSMAP 400/500 series chartplotter using a 500 W transducer, and no core. Some transducers are... only compatible with either the GPSMAP 525/535/545/555/526/536/546/556 or with non "s" models compatible with water or light mineral oil. 3. Build a dam using this method. Contact...
Installation Instructions
Page 10
... alloy, waterproof to a different location. Update Rate: 1/second, continuous GPS Accuracy: Position: Return the boat to the speed at or near the... suddenly is lost . GPSMAP 525/526/535/536/545/546/555/556 (s): 5.0 in small increments. Acquisition Times: (Average acquisition times for a stationary receiver with adjustable brightness, 640... × 480 pixels, capable of the transducer, make the adjustments in . To test the transom mount...
... alloy, waterproof to a different location. Update Rate: 1/second, continuous GPS Accuracy: Position: Return the boat to the speed at or near the... suddenly is lost . GPSMAP 525/526/535/536/545/546/555/556 (s): 5.0 in small increments. Acquisition Times: (Average acquisition times for a stationary receiver with adjustable brightness, 640... × 480 pixels, capable of the transducer, make the adjustments in . To test the transom mount...