Users Manual - English
Page 87
... as you turn on the power switch. When the Status LED comes on, release the Go button. ■ For more information on . When the Toner LED comes on, release the Go button. 4 Hold down the Go button and keep it pressed down until the green Status LED comes on . The... Network User's Guide or visit http://solutions.brother.com ■ You can also disable the APIPA protocol using EWS, BRAdmin Professional or Web BRAdmin. Network factory default setting (For HL-5170DN) If you wish to reset the print server back to its default factory settings (resetting all the LEDs light up again, the...
... as you turn on the power switch. When the Status LED comes on, release the Go button. ■ For more information on . When the Toner LED comes on, release the Go button. 4 Hold down the Go button and keep it pressed down until the green Status LED comes on . The... Network User's Guide or visit http://solutions.brother.com ■ You can also disable the APIPA protocol using EWS, BRAdmin Professional or Web BRAdmin. Network factory default setting (For HL-5170DN) If you wish to reset the print server back to its default factory settings (resetting all the LEDs light up again, the...
Users Manual - English
Page 103
See the instructions supplied with the new drum unit. Caution ■ The Drum LED indication does not disappear until you reset the drum counter. ■ Do not reset the drum counter when you replace only the toner cartridge. 8 Close the front cover. 9 Make sure that the printer is turned on, the front cover is open and the Status LED is now off. Figure 5-20 7 Reset the drum counter. ROUTINE MAINTENANCE 5 - 11 6 Put the drum unit assembly in the printer. Make sure that the Drum LED is red.
See the instructions supplied with the new drum unit. Caution ■ The Drum LED indication does not disappear until you reset the drum counter. ■ Do not reset the drum counter when you replace only the toner cartridge. 8 Close the front cover. 9 Make sure that the printer is turned on, the front cover is open and the Status LED is now off. Figure 5-20 7 Reset the drum counter. ROUTINE MAINTENANCE 5 - 11 6 Put the drum unit assembly in the printer. Make sure that the Drum LED is red.
Service Manual
Page 69
.... NOTE: *If you turn on , release the Go button. (5) When all the LEDs except for Toner LED go off the printer. (2) Make sure that the front cover is closed and the power cord is... if the print server is receiving or transmitting data. 6.2 Network Factory default setting (For HL-5170DN) If you wish to reset the print server back to 4 above, however, hold down until the yellow Status LED ...comes on APIPA, see the Network User's Guide or visit http://solutions.brother.com 2-36 When the ...
.... NOTE: *If you turn on , release the Go button. (5) When all the LEDs except for Toner LED go off the printer. (2) Make sure that the front cover is closed and the power cord is... if the print server is receiving or transmitting data. 6.2 Network Factory default setting (For HL-5170DN) If you wish to reset the print server back to 4 above, however, hold down until the yellow Status LED ...comes on APIPA, see the Network User's Guide or visit http://solutions.brother.com 2-36 When the ...
Service Manual
Page 174
...you reset the drum counter. • It is recommended to local regulations, keeping it off . ! Once all four LEDs are lit, release the Go button. (8) Close the front cover. (9) Make sure that toner powder does not spill out of the drum unit assembly. (Fig.5-4) HL-5130/5140/5150D/...5170DN SERVICE MANUAL (4) Unpack the new drum unit. (5) Put the toner cartridge in the printer. Refer to subsection 3. 'PERIODICAL CLEANING' in this...
...you reset the drum counter. • It is recommended to local regulations, keeping it off . ! Once all four LEDs are lit, release the Go button. (8) Close the front cover. (9) Make sure that toner powder does not spill out of the drum unit assembly. (Fig.5-4) HL-5130/5140/5150D/...5170DN SERVICE MANUAL (4) Unpack the new drum unit. (5) Put the toner cartridge in the printer. Refer to subsection 3. 'PERIODICAL CLEANING' in this...
Service Manual
Page 192
....) Clean the corona wire. (Refer to Section 3 of Chapter 5.) Clean the electrodes of the main body and drum unit. (Refer to be necessary to reset the printer with a new one. Close the front cover. The printer automatically recovers from the tray 2 results in this Chapter.) 6-4 Clear the jammed paper... indicates on the manual feed slot or the MP tray. Close the jam clear cover of error Toner empty Cover open (Front cover) Cover open (Jam clear cover) Paper jam No paper (HL-5130) No paper (HL5140/5150D/5170 DN) No tray 1 Manual feed Memory full Print overrun Clean drum unit...
....) Clean the corona wire. (Refer to Section 3 of Chapter 5.) Clean the electrodes of the main body and drum unit. (Refer to be necessary to reset the printer with a new one. Close the front cover. The printer automatically recovers from the tray 2 results in this Chapter.) 6-4 Clear the jammed paper... indicates on the manual feed slot or the MP tray. Close the jam clear cover of error Toner empty Cover open (Front cover) Cover open (Jam clear cover) Paper jam No paper (HL-5130) No paper (HL5140/5150D/5170 DN) No tray 1 Manual feed Memory full Print overrun Clean drum unit...
Service Manual
Page 244
LED Toner Type of the internal fonts. The printer prints a list of mode Test Sample Page Drum Paper Print Fonts (HL-5140/5150D/5170DN only) Factory Reset Status Network factory reset (yellow) (APIPA: ON) Status Network factory reset (green) (APIPA: OFF) Function The printer prints a test sample page. The printer returns to Section 6.2 of Chapter 2. 7-1 The network setting...
LED Toner Type of the internal fonts. The printer prints a list of mode Test Sample Page Drum Paper Print Fonts (HL-5140/5150D/5170DN only) Factory Reset Status Network factory reset (yellow) (APIPA: ON) Status Network factory reset (green) (APIPA: OFF) Function The printer prints a test sample page. The printer returns to Section 6.2 of Chapter 2. 7-1 The network setting...
Service Manual
Page 257
It is switched to 400V again when the toner cartridge is switched from the drum unit life.) The developing bias is replaced following settings, the developing bias reset function operates. 1. This function helps a counter reset for the main items to 300V when 7,000 pages are as follows; ...front cover open . 5. NVRAM DEFAULT VALUE The default values for initializing the developing bias function when changing the new toner cartridge before the previous one gets empty. Toner LED: ON, Status LED: ON (Red) (Counted from the number of Drum LED ON Development switching timing Fixing...
It is switched to 400V again when the toner cartridge is switched from the drum unit life.) The developing bias is replaced following settings, the developing bias reset function operates. 1. This function helps a counter reset for the main items to 300V when 7,000 pages are as follows; ...front cover open . 5. NVRAM DEFAULT VALUE The default values for initializing the developing bias function when changing the new toner cartridge before the previous one gets empty. Toner LED: ON, Status LED: ON (Red) (Counted from the number of Drum LED ON Development switching timing Fixing...