Technical Reference
Page 413
2001/10/02 APPENDIX C HBP MODE COMMANDS APPENDIX C HBP MODE COMMANDS - 1
2001/10/02 APPENDIX C HBP MODE COMMANDS APPENDIX C HBP MODE COMMANDS - 1
Technical Reference
Page 415
... ( This is not a control code.) B: character string enclosed in parentheses means 1 data byte described in binary format CHR$(•): character of data +: sign for the HL-820/1020/1040 printers only. 1.
... ( This is not a control code.) B: character string enclosed in parentheses means 1 data byte described in binary format CHR$(•): character of data +: sign for the HL-820/1020/1040 printers only. 1.
Technical Reference
Page 416
..., IBM emulation, Epson emulation and Auto emulation for HL-1040). This mode continues until one of following HBP commands in HBP mode. The printer executes the following occurs. (1) The printer receives the Exit command. (2) The printer power is turned off. (3) InputPrime Signal is received. Explanation The printer can receive this command when it receives this command...
..., IBM emulation, Epson emulation and Auto emulation for HL-1040). This mode continues until one of following HBP commands in HBP mode. The printer executes the following occurs. (1) The printer receives the Exit command. (2) The printer power is turned off. (3) InputPrime Signal is received. Explanation The printer can receive this command when it receives this command...
Technical Reference
Page 419
... - 7 However, there are two exceptions. If the value is set to 0, the sleep time is set to 255, the printer does not go into sleep mode. For the HL-1040, the command is valid during HBP mode only, it is valid both in HBP mode and in minutes. The sleep time...binary data (0-255) after the @T command indicates the minute(s) delay to entering sleep mode. Note2: HL-1040 also accepts the PJL command which sets the sleep time. Note1: Sleep time means the time from the last printer operation (printing, key pressing, motor being driven) to entering sleep mode. 1 byte of the ...
... - 7 However, there are two exceptions. If the value is set to 0, the sleep time is set to 255, the printer does not go into sleep mode. For the HL-1040, the command is valid during HBP mode only, it is valid both in HBP mode and in minutes. The sleep time...binary data (0-255) after the @T command indicates the minute(s) delay to entering sleep mode. Note2: HL-1040 also accepts the PJL command which sets the sleep time. Note1: Sleep time means the time from the last printer operation (printing, key pressing, motor being driven) to entering sleep mode. 1 byte of the ...
Technical Reference
Page 420
.... Bit1: Not used Bit2:0 = The printer generates an error when an undefined code is as 8 bits, that is recognized as undefined code.) Bit5: Not used Bit6: Not used Bit7: Select printer error messages ON or OFF. (HL-820/1020/1040) 0: The printer does not print an error message when an... error occurs. 1: The printer prints an error message when an error occurs. The printer does not recover automatically from a Print Overrun error. Bit3:...
.... Bit1: Not used Bit2:0 = The printer generates an error when an undefined code is as 8 bits, that is recognized as undefined code.) Bit5: Not used Bit6: Not used Bit7: Select printer error messages ON or OFF. (HL-820/1020/1040) 0: The printer does not print an error message when an... error occurs. 1: The printer prints an error message when an error occurs. The printer does not recover automatically from a Print Overrun error. Bit3:...
Technical Reference
Page 422
... of data following this form feed command when a Print Overrun error occurs. 3.2.9 Exit commands Command @X Function This command exits from HBP mode The HL-1040 printer is handled as the printer will improve the print performance. 3.2.8 Formfeed commands Command @F Remark: The last raster scan on each page should be a white raster. It is more...
... of data following this form feed command when a Print Overrun error occurs. 3.2.9 Exit commands Command @X Function This command exits from HBP mode The HL-1040 printer is handled as the printer will improve the print performance. 3.2.8 Formfeed commands Command @F Remark: The last raster scan on each page should be a white raster. It is more...
Technical Reference
Page 425
... of a print job. %-12345X@PJL @PJL DEFAULT AUTOSLEEP=0 @PJL DEFAULT TIMEOUTSLEEP= 15 %-12345X@PJL @PJL ENTER LANGUAGE = HBP @L @E @T @M @J @J @G @G+ @F @G @G+ @F @X used for HL-820/1020/1040 used for HL-820/1020/1040 used for HL-820/1020/1040 Enter into HBP mode Set 600 dpi resolution Set economy mode off Set Sleep time to 15 minutes Set mode...
... of a print job. %-12345X@PJL @PJL DEFAULT AUTOSLEEP=0 @PJL DEFAULT TIMEOUTSLEEP= 15 %-12345X@PJL @PJL ENTER LANGUAGE = HBP @L @E @T @M @J @J @G @G+ @F @G @G+ @F @X used for HL-820/1020/1040 used for HL-820/1020/1040 used for HL-820/1020/1040 Enter into HBP mode Set 600 dpi resolution Set economy mode off Set Sleep time to 15 minutes Set mode...