Biostar P4M80-M7A V7.X Support and Manuals
Get Help and Manuals for this Biostar item
View All Support Options Below
Free Biostar P4M80-M7A V7.X manuals!
Problems with Biostar P4M80-M7A V7.X?
Ask a Question
Free Biostar P4M80-M7A V7.X manuals!
Problems with Biostar P4M80-M7A V7.X?
Ask a Question
Most Recent Biostar P4M80-M7A V7.X Questions
Lan Problems
I cannot install drivers for ethernet. Either on board LAn or pci card
I cannot install drivers for ethernet. Either on board LAn or pci card
(Posted by mcbutzke 12 years ago)
Popular Biostar P4M80-M7A V7.X Manual Pages
P4M80-M7A user's manual - Page 1
... this user's manual is not allowed without obligation to notify any party beforehand. The content of this publication and to make changes to Part 15 of the FCC Rules. These limits are trademarks of a Class B digital device, pursuant to the contents here without first obtaining the vendor's approval in a particular installation.
There is...
P4M80-M7A user's manual - Page 2
... 10
Central Processing Unit (CPU 10 FAN Headers 11 Memory Module Installation 12 Connectors and Slots 13
Chapter 3: Headers & Jumpers Setup 14
3.1
How to Setup Jumpers 14
3.2
Detail Settings 14
Chapter 4: Useful Help 18
4.1
Award BIOS Beep Code 18
4.2
Extra Information 18
4.3
Troubleshooting 20
Chapter 5: WarpSpeeder 21
5.1
Introduction 21
5.2
System Requirement 21...
P4M80-M7A user's manual - Page 3
... Code CPU. VIA P4M800CE (for P4M800-M7).
H/W Monitor, - Dimension ATX Form Factor: 24.38cm (L) x 20.19cm (W)
Main Memory
Supports up to 3.8GHz.
Fan Speed Controller, - ITE "Smart Guardian" function.
1 Chipset North Bridge: VIA P4M800CD (for P4M800-M7 A v1.0 and v7.0). Super I/O Chip: ITE IT8705AF Provides the most commonly used legacy super I/O functionality. Hardware...
P4M80-M7A user's manual - Page 5
... In/ Surround Line Out Mic In 1/ Base/Center
B.
Software Supports 9th TouchTM, FlasherTM, WinFlasherTM, and WarpspeederTM. Offers the highest performance for Windows 98SE, Windows NT, Windows 2000, Windows ME, Windows XP, Red-Hat Linux, and UNIX series.
1.2 PACKAGE LIST
FDD cable x1 HDD cable x1 User's Manual x1 Fully Setup Driver CD x1 Rear I/O panel for ATX case x1 USB...
P4M80-M7A user's manual - Page 15
.../s. It has two HDD connectors IDE1 (primary) and IDE2 (secondary). CNR1: Communication Network Riser Slot
The CNR specification is also equipped with 2 channels SATA interface, it defines a hardware scalable riser card interface, which supports modem only. JSATA1/JSATA2: Serial ATA Connectors
The motherboard has a PCI to four hard disk drives. PCI stands...
P4M80-M7A user's manual - Page 16
... A
CHAPTER 3: HEADERS & JUMPERS SETUP
3.1 HOW TO SETUP JUMPERS
The illustration shows how to connect additional USB cable on the PC front panel, and also can be placed on pins, the jumper is "close Voltage
JUSBLAN1 are powered by
+5V standby voltage.
Pin opened
Pin closed
Pin1-2 closed
3.2 DETAIL SETTINGS
JUSBV1/JUSBV2: Power Source...
P4M80-M7A user's manual - Page 18
... AC. 6. Pin 2-3 close
Normal Operation (Default). Wait for five seconds. 4. Reset your desired password or clear the CMOS data.
16 Pin
Assignment
1
JCDIN1
1
Left channel input
2
Ground
3
Ground... This connector allows user to "Pin 2-3 close ". 5.
Set the jumper to "Pin 1-2 close ". 3.
Remove AC power line. 2. Set the jumper to connect the audio source from the veriaty devices...
P4M80-M7A user's manual - Page 20
... automatically No error found during POST No DRAM detected or install
4.2 EXTRA ...CODE
Beep Sound One long beep followed by virus, the Boot-Block function will help to restore BIOS. Insert the bootable disk into floppy disk. 5. Download the Flash Utility "AWDFLASH.exe" from Biostar website. 4. Confirm motherboard model and download the respectively BIOS
from the Biostar
website: www.biostar...
P4M80-M7A user's manual - Page 22
... files. Hard disk can be read and applications can be used but booting from disk to the system at any time. Cannot boot system after installing second hard drive.
1. Run SETUP program and select correct drive types. Make sure power cable is in . Check cable running from hard disk 2.
P4M800-M7 & P4M800-M7 A
4.3 TROUBLESHOOTING...
P4M80-M7A user's manual - Page 23
... shown on the other hand, helps to install DirectX 8.1.)
21 The cool Hardware Monitor smartly...Windows XP, you can get detail descriptions about BIOS model and chipsets. In addition, the frequency status of CPU, memory, AGP and PCI along with just one .
5.2 SYSTEM REQUIREMENT
OS Support: Windows 98 SE, Windows Me, Windows 2000, Windows XP DirectX: DirectX 8.1 or above. (The Windows XP...
P4M80-M7A user's manual - Page 24
When you see the following dialog in this user manual will pop up. INSTALLATION
Execute the setup execution file, and then the following figures are just only for reference, the screen printed in setup procedure, it means setup is checked, the Tray Icon utility and [WarpSpeeder™] utility will be automatically and immediately launched after you click...
P4M80-M7A user's manual - Page 27
The default setting is "No". If you want to get the best performance of overclocking, we recommend you can decide to up as the following figure. Voltage Panel
...
P4M80-M7A user's manual - Page 28
Warning: Manually overclock is potentially dangerous, especially when the overclocking percentage is over 110 %.
Let user select a restoring way if system need to do real-time overclock ...
P4M80-M7A user's manual - Page 29
... button": User can get the real-time status information of testing until system fail.
In this button and
[WarpSpeeder™] will set the best and stable performance and frequency automatically. [WarpSpeeder™] utility will do a fail-safe rebooting. If the testing fail, system will slide out to ...
P4M80-M7A user's manual - Page 30
About Panel
Click the "about" button in hints of [WarpSpeeder™] utility.
28 In this panel, you can also get model name and detail information in Main Panel, the button will be highlighted and the About Panel will slide out to overclocking. P4M800-M7 & P4M800-M7 A 6. ...
Biostar P4M80-M7A V7.X Reviews
We have not received any reviews for Biostar yet.