BenQ TK850 Support and Manuals
BenQ TK850 Videos
Popular BenQ TK850 Manual Pages
RS232 Control Guide - Page 3
...
5
GND
6
NC
7
RTS
8
CTS
9
NC
3 Follow the procedures to complete the connection and settings first, and refer to control your BenQ projector via RS232 from a computer. Available functions and commands vary by model. Check the specifications and user manual of the purchased projector for RS232 commands. Introduction
The document describes how to the command table for product...
RS232 Control Guide - Page 8
...61623; Available features differ by projector specification, input sources, settings, etc.. Commands are working if the standby power is 0.5W or a supported baud rate of the projector is performed via LAN, ...If a command with correct format is not valid for the projector model, it will echo Block item. If RS232 control is set. Uppercase, lowercase, and a mixture of both...
User Manual - Page 2
... warranty shall be void if the customer fails to operate the product in accordance with BenQ's written instructions, especially the ambient humidity must be required with respect to the contents hereof and specifically disclaims any warranties, merchantability or fitness for the details on BenQ projector patent coverage.
2 Warranty and Copyright information All rights reserved. Further...
User Manual - Page 3
... ...17 Starting up the projector ...17 Using the menus ...19 Upgrading firmware ...19 Securing the projector ...19 Switching input signal ...21 Presenting from a Media Reader...22 Shutting down the projector ...22 Direct power off ...22 Menu operation ...23 PICTURE menu ...23 DISPLAY menu ...27 INSTALLATION menu...28 SYSTEM SETUP: BASIC menu...29 SYSTEM SETUP: ADVANCED menu 30 INFORMATION...
User Manual - Page 4
... this manual before you operate your projector through a power stabilizer, surge protector or
uninterruptible power supply (UPS).
3. To temporarily turn off the lamp, use of this product, it is important that you follow the instructions mentioned in this could cause the objects to break on the product.
1. Allow the projector to cool for replacement.
8. Do...
User Manual - Page 11
... screen and the BenQ
dealer to mount your projector. Note that a
BenQ Projector Ceiling/Wall Mount Kit from behind the screen. After turning on the table behind the screen.
Rear Table
Select this location with the projector placed on the projector, go to INSTALLATION Menu > Projector Position and press / to position the projector for quick setup and portability.
2. Front...
User Manual - Page 19
... to adjust the settings or press OK on the projector or remote control to enter the sub-menu.
• Press MENU twice* on until updating finished.
6. Go to BenQ Website and enter into USB 3.0 port.
4. Upgrading firmware
1.
Select Yes to SYSTEM SETUP: ADVANCED > Firmware Upgrade menu and press OK.
5. Insert USB flash drive into Product page > Support > Software to use...
User Manual - Page 20
... in advance or right after the password is available to you should you desire to set , the OSD menu returns to SYSTEM SETUP: ADVANCED Menu > Password. Press and hold OK for the password.
4.
Utilizing the password function
Setting a password
1.
Seek help from the local BenQ service center to prevent theft. See item 9 on lock is usually a combination of the projector.
User Manual - Page 21
... be scaled by re-entering the new password. Confirm the new password by the projector depending upon the "aspect ratio" setting, which outputs at the same time. Be sure the SYSTEM SETUP: BASIC Menu > Auto Source menu is selected and press OK. Though the password function is incorrect, the password error message will appear, and the message "Input...
User Manual - Page 24
...from among 1.8/2.0/2.1/2.2/2.3/2.4/2.5/2.6/BenQ. You can be overpowering, which makes the image unrealistic. User Mode Management
Brightness Contrast Color Tint Sharpness
Advanced
• Load Settings From
There is...the image becomes brighter; The new name can also manually select a brightness level to select User.
3. Adjust this projector. When the value is lower, the image becomes ...
User Manual - Page 27
...images.
• 3D Mode: The default setting is suitable for more comfortable 3D viewing experience. If the projector cannot recognize the 3D format, manually choose a 3D mode according to your ...the four edges. The projector supports HDR imaging sources. It is Auto and the projector automatically chooses an appropriate 3D format when detecting 3D contents.
Setting 0 means the picture...
User Manual - Page 29
...unnecessary waste of the adjustments you may make manual adjustments with immersive cinematic audio experience.
The ...projector to turn off . Auto Source Allows the projector to your desired name.
Setting the sound mute or changing the sound level will turn on or off automatically if no input signal is setting On or Off here.
SYSTEM SETUP: BASIC menu
Language
Sets...
User Manual - Page 30
...HDMI Settings
Adjusts the equalizer gain settings for an HDMI signal.
When the Key Lock is turned on. Password
See Utilizing the password function on the projector will still be returned to the projector with..., press and hold (the right key) on the projector or remote control for example). SYSTEM SETUP: ADVANCED menu
Lamp Settings
• Reset Lamp Timer: See Resetting the lamp timer...
User Manual - Page 33
...down to replace the lamp, please consult your dealer.
Press to SYSTEM SETUP: ADVANCED Menu > Lamp Settings and press OK. Setting the projector in OSD menu:
-
The Lamp Settings page appears.
2.
Time used in each lamp mode in some instances the lamp may vary within the lamp manufacturers specifications. 2. When you calculate Equivalent Lamp hour manually, it shows...
BenQ TK850 Reviews
Do you have an experience with the BenQ TK850 that you would like to share?
Earn 750 points for your review!
We have not received any reviews for BenQ yet.
Earn 750 points for your review!