BenQ SH910 Support and Manuals
Get Help and Manuals for this BenQ item
Popular BenQ SH910 Manual Pages
SH910 User Manual - Page 1
SH910 Digital Projector User Manual
Welcome
SH910 User Manual - Page 4
... Excessive operation
projector. There are dangerous high
of lamps beyond the
11. The only user serviceable part is under operation, you
ever undo or remove any electronic components unless the projector is a normal phenomenon and not a product defect.
4 Important safety instructions Refer servicing only to break on an unstable cart, stand, or table. Never replace the lamp assembly or...
SH910 User Manual - Page 8
... all of purchase. Ceiling mount kit
3. Spare lamp kit 2. RS232 cable
8 Introduction If any of these items are missing, please contact your region, and may differ from those illustrated.
*The warranty card is only supplied in some specific regions. Projector
Power cord
VGA cable
Quick start guide
User manual CD
Warranty card*
Remote control with batteries
Optional accessories...
SH910 User Manual - Page 10
...lamp has developed a problem. See "Auto-adjusting the image" on page 24 for details. Controls and functions
Projector
6.
1
7.
2
3
12
4
11
5
5
6
10 8.
7
3
89
1. Zoom ring
Adjusts the size of the lamp. MENU/EXIT
Turns on page 79 for details. exits and saves menu settings.
5. Lights up red if the projector... picture setup mode.../
Down)
Manually corrects distorted ...
SH910 User Manual - Page 15
... near the floor in the SYSTEM SETUP: Basic > Projector Position menu after you select. Set Rear Ceiling in front of the screen. This is required. Purchase the BenQ Projector Ceiling Mounting Kit from the ceiling in the SYSTEM SETUP: Basic > Projector Position menu after you turn the projector on . Front Ceiling Select this installation location. Take into consideration the size...
SH910 User Manual - Page 22
... for approximately 90 seconds before energizing the lamp.
4. See "Utilizing the password function" on function is activated in the screen. The current input signal being scanned displays in the SYSTEM SETUP: Basic > Operation Settings menu, the projector will continue displaying until an input signal is on . 7. Turn on the remote control to start to adjust the...
SH910 User Manual - Page 26
...inconvenienced if you used unless the correct password is entered every time the projector is activated, you will be asked to the lock's documentation for setting up password security. Setting a password
Once a password has been set through the On-Screen Display (OSD) menu. As pictured to the SYSTEM SETUP: Advanced > Security Settings menu. Otherwise, purchase a lock, such as asterisks...
SH910 User Manual - Page 27
... Off by re-entering the new password. 6. Seek help from the local BenQ service center to the SYSTEM SETUP: Advanced > Security Settings > Change password menu.
2. Changing the password
1. Enter the old password.
• If the password is correct, another password.
4. Remember to enter the password next time you turn off your projector.
3. Write down in a safe place.
5. You...
SH910 User Manual - Page 28
... results, you ever need to re-activate the password function by the projector depending upon the 'aspect ratio' setting, which is multiple equipment connected to the projector, repeat steps 1-2 to select a suitable
color space. However, it can be scaled by entering the old password. If there is the default of picture clarity.
A source selection bar displays...
SH910 User Manual - Page 46
If you to enter Basic, Wired LAN, Wireless LAN and Mail pages once the password is "0000".
Press exit to go back to change the password, please enter Basic page.
46 Operation The default password is entered. The Admin page allows you want to the Crestron remote network operation page. i
i. The info page displays the information and status of this projector.
SH910 User Manual - Page 75
... for a replacement lamp.
If the projector is strongly recommended that you notice that vary depending on -screen
instructions to dismiss the message. The lamp is normal lamp behavior.
"XXXX" shown in some instances the lamp may continue to change the lamp.
Status
Message
Install a new lamp for details. You can replace the lamp whenever you replace the lamp at this...
SH910 User Manual - Page 77
... it too quickly may cause injuries.
4. If you touch the optical components inside the projector may cause the lamp to break and scatter broken glass in the projector.
• Do not place the lamp in the projector. Insert the new lamp into the projector after the lamp is removed. Maintenance 77 Use the handle to slowly pull the...
SH910 User Manual - Page 88
....
• All BenQ monitors and projectors come with user manuals on the BenQ's web site (www.BenQ.com ). Accessibility Requirements for Rehabilitation Act of 1973, Section 508
BenQ's commitment to accessible products allows us to support government in suspend or sleep mode and is using less than 2 watts of electricity.
• BenQ's monitors have a variety of settings of pre-programmed...
SH910 Data Sheet - Page 1
...
Specifications
...Throw Ratio
1.4-2.1 (65"@ 6.65 ft)
Image Size Diagonal
24" ~ 300"
Zoom Ratio
1.5:1
Lamp Type
OSRAM 280W
Lamp Life (Normal/Eco Mode) 2000/3000 hours
Keystone Adjustment
Manual Vertical +/- 20 degrees
Projection Offset
167%±5%
Resolution Support... Keyboard/Mouse & Wireless Dongle)
USB (Type...SH910 DIGITAL
PROJECTOR
FULL HD
1080P
Features
Native 1080P (1920x1080) ...
SH910 Data Sheet - Page 2
Distance Chart
SH910 Digital Projector
Ceiling Mount Chart
4.35"
5.9" .984"
.02" 9.35"
Dimensions
.925"
23120.62m6"m
1050.4.46m4"m
28173..33m5"m
4.566"
3.937"
1.594" 4.748"
2.559" 6.57" 13.354"
BenQ SH910 Reviews
We have not received any reviews for BenQ yet.