TP-Link TL-SG3216 Support and Manuals
Get Help and Manuals for this TP-Link item
View All Support Options Below
Free TP-Link TL-SG3216 manuals!
Problems with TP-Link TL-SG3216?
Ask a Question
Free TP-Link TL-SG3216 manuals!
Problems with TP-Link TL-SG3216?
Ask a Question
Most Recent TP-Link TL-SG3216 Questions
TP-Link TL-SG3216 Videos
TP-LINK TL-SG3216 on innvisio.com
Duration: :19
Total Views: 505
Duration: :19
Total Views: 505
Popular TP-Link TL-SG3216 Manual Pages
TL-SG3216 V1 User Guide - Page 1
TL-SG3216/TL-SG3424 JetStream L2 Lite Managed Switch
Rev: 1.0.2 1910010512
TL-SG3216 V1 User Guide - Page 8
...
The following items should be found in your box: ¾ One JetStream L2 Lite Managed Switch ¾ One power cord ¾ One console cable ¾ Two mounting brackets and other fittings ¾ Installation Guide ¾ Resource CD for TL-SG3216/TL-SG3424 Switch, including:
• This User Guide • Other Helpful Information Note: Make sure that the package...
TL-SG3216 V1 User Guide - Page 9
... result in a malfunction or damage to the device.
Introduces how to log on to the Switch
Introduction
Introduces the guide structure and conventions. Symbols in this Guide stands for setup and management of TL-SG3216/TL-SG3424 JetStream L2 Lite Managed Switch. This format indicates important information that is intended for network managers familiar with IT concepts...
TL-SG3216 V1 User Guide - Page 13
... enables monitoring selected ingress/egress traffic.
6 Chapter 2 Introduction
Thanks for choosing the TL-SG3216/TL-SG3424 JetStream L2 Lite Managed Switch!
2.1 Overview of the Switch
Designed for workgroups and departments, TL-SG3216/TL-SG3424 from TP-LINK provides wire-speed performance and full set of Service + Supports L2/L3 granular CoS with 4 priority queues per port. + Rate limiting...
TL-SG3216 V1 User Guide - Page 15
... Switch provides 4 SFP module ports (21F, 22F, 23F, 24F). Please make sure the voltage of the power supply meets the requirement of TL-SG3216/TL-SG3424 features a power socket and a Grounding Terminal (marked with the port 21T-24T respectively.
2.3.2 Rear Panel
The rear panel of the input voltage (100-240V~ 50/60Hz 0.6A). ...
TL-SG3216 V1 User Guide - Page 124
... VLAN of the access port in two modes: automatic mode and manual mode. stream
TRUNK：Supported. A voice VLAN can configure its security mode to filter data stream. Automatic Mode: In this port from voice device and the link type of the port and processing mode
Automatic Mode
TAG voice ACCESS: Not supported. GENERAL：Supported. GENERAL: Supported...
TL-SG3216 V1 User Guide - Page 188
...firmware version and so on three protocols, NDP, NTDP and CMP (Cluster Management Protocol). A switch keeps and maintains a neighbor information table, which contains the NDP information of each neighbor switch. Choose the menu Cluster→NDP→Neighbor Info to the collected NTDP information. Note: TL-SG3216/TL... of each device in a specific network range to neighbor devices ...
TL-SG3216 V1 User Guide - Page 199
... candidate switch.
13.4 Application Example for Cluster Function
¾ Network Requirements Three switches form cluster, one commander switch (Here take TP-LINK TL-SL5428E as an example) and two member switches (Here take TP-LINK TL-SG3216 as an example). Figure 13-14 Cluster Configuration for Individual Switch The following entries are displayed on this screen: ¾...
TL-SG3216 V1 User Guide - Page 221
... Client.
1. Installation Guide
1) Insert the provided CD into...setup shown as the authenticator system, please take the following figure. Choose the proper language and click Next to load the following instructions to install the TpSupplicant provided on the attached CD for 802.1X authentication.
Figure D-2 Preparing Setup 3) Then the following screen. When the switch TL-SG3216...
TL-SG3216 V1 CLI Reference Guide - Page 1
TL-SG3216/TL-SG3424 JetStream L2 Lite Managed Switch
Rev: 1.0.2 1910010511
TL-SG3216 V1 CLI Reference Guide - Page 12
... and the connected Port number of this Guide stands for TL-SG3216/TL-SG3424 JetStream L2 Lite Managed Switch. Chapter 11: Binding Table Commands Provide information about the commands used for user management. Chapter 5: Protocol VLAN Commands Provide information about the commands used for configuring LAG (Link Aggregation Group). Chapter 8: LAG Commands Provide information about...
TL-SG3216 V1 CLI Reference Guide - Page 54
...Command Mode
Global Configuration Mode
Example
Delete the user named tplink: TP-LINK(config)# user remove tplink
user modify status
Description
The user modify status command is used to modify the status of tplink to delete an existing user. The existing user name.... user remove
Description
The user remove command is used to enabled: TP-LINK(config)# user modify status tplink enable
43
TL-SG3216 V1 CLI Reference Guide - Page 55
...;
The existing user name. new-password -- Access level. Syntax
user modify password user-name old-password new-password confirm-password
Parameter
user-name -- Command Mode
Global Configuration Mode
Example
Change the access level of tplink to admin: TP-LINK(config)# user modify type tplink admin
user modify password
Description
The user modify password command is used to modify the...
TL-SG3216 V1 CLI Reference Guide - Page 56
... tplink as newpwd: TP-LINK(config)# user modify password tplink password newpwd newpwd
user access-control disable
Description
The user access-control disable command is used to limit the IP-range of the users for login. Only the current host and the users within the IP-range you set here are allowed for login. The source IP...
TL-SG3216 V1 CLI Reference Guide - Page 109
...
Example
Configure the system time mode as manual, and the time is 12/20/2010 17:30:35 TP-LINK(config)# system-time manual 12/20/2010-17:30:35
ip ...Set the date and time manually, MM/DD/YYYY-HH:MM:SS
Command Mode
Global Configuration Mode
Example
Configure the system mode as gmt, the time zone is -12, the primary ntp server is 133.100.9.2 and the secondary ntp server is 139.78.100.163: TP-LINK...
TP-Link TL-SG3216 Reviews
We have not received any reviews for TP-Link yet.