User Manual
Page 7
...shield up against tractor. CHECK DECK LEVELNESS For best cutting results, mower housing should be properly inflated for replacing motion and mower blade drive belts in neutral (N) position. • Roll tractor forward off the skid. Verify that the brake is operating properly. See "TO ...10003; Become familiar with the instructions that all connections are still secure and wires are shown for leveling). ✓ Check mower and drive belts. Operate them before tightening adjustment knob. • Remove adjustment knob and flat washer securing seat to -rear for best cutting results....
...shield up against tractor. CHECK DECK LEVELNESS For best cutting results, mower housing should be properly inflated for replacing motion and mower blade drive belts in neutral (N) position. • Roll tractor forward off the skid. Verify that the brake is operating properly. See "TO ...10003; Become familiar with the instructions that all connections are still secure and wires are shown for leveling). ✓ Check mower and drive belts. Operate them before tightening adjustment knob. • Remove adjustment knob and flat washer securing seat to -rear for best cutting results....
User Manual
Page 17
... engine's air cooling system. Remove blower housing and clean the area shown to keep water out. Debris can restrict clutch/brake pedal shaft movement, causing belt slip and loss of all foreign matter. • Clean debris from tractor and mower. FUEL FILTER Fig. 16 00667 17 MUFFLER Inspect and replace corroded... TOP SIDE STEERING PLATE CAUTION: PINCH POINTS STEERING SYSTEM, DASH, FENDER AND MOWER NOT SHOWN Fig. 17 • Keep finished surfaces and wheels free of drive.
... engine's air cooling system. Remove blower housing and clean the area shown to keep water out. Debris can restrict clutch/brake pedal shaft movement, causing belt slip and loss of all foreign matter. • Clean debris from tractor and mower. FUEL FILTER Fig. 16 00667 17 MUFFLER Inspect and replace corroded... TOP SIDE STEERING PLATE CAUTION: PINCH POINTS STEERING SYSTEM, DASH, FENDER AND MOWER NOT SHOWN Fig. 17 • Keep finished surfaces and wheels free of drive.
User Manual
Page 21
...MANDREL PULLEY IDLER PULLEYS TO REPLACE MOTION BELT DRIVE (See Fig. 29) Park the tractor on level surface. NOTE: Observe entire motion drive belt and position of all belt guides. • Install mower (See "To Install Mower" in this section of manual). • Work belt off the steering plate (F) and remove...brake must lock and skid when you try to manually push the tractor forward. SERVICE AND ADJUSTMENTS TO REPLACE MOWER BLADE DRIVE BELT (See Fig. 28) The mower blade drive belt may also check brake by: • Park tractor on a level, dry concrete or paved surface, depress brake pedal...
...MANDREL PULLEY IDLER PULLEYS TO REPLACE MOTION BELT DRIVE (See Fig. 29) Park the tractor on level surface. NOTE: Observe entire motion drive belt and position of all belt guides. • Install mower (See "To Install Mower" in this section of manual). • Work belt off the steering plate (F) and remove...brake must lock and skid when you try to manually push the tractor forward. SERVICE AND ADJUSTMENTS TO REPLACE MOWER BLADE DRIVE BELT (See Fig. 28) The mower blade drive belt may also check brake by: • Park tractor on a level, dry concrete or paved surface, depress brake pedal...
User Manual
Page 26
...10. Clean around mandrels to open vent holes. 1. Loose or damaged wiring. 5. Check/replace light switch. 4. Replace battery. 2. Motion drive belt worn, damaged, or broken. 3. See "CLEANING" in "FAST" position. 2. Bent blade mandrel. 3. CORRECTION 1. Poor cut - ...throttle control in the maintenance section. 2. Check wiring and connections. 5. Obstruction in parts manual. 11. Replace mower drive belt. 3. Wet grass. 3. Replace mower drive belt. 9. Engine speed too slow. 1. Shift to dry before mowing. 4. Replace fuse. Replace blade. Replace with...
...10. Clean around mandrels to open vent holes. 1. Loose or damaged wiring. 5. Check/replace light switch. 4. Replace battery. 2. Motion drive belt worn, damaged, or broken. 3. See "CLEANING" in "FAST" position. 2. Bent blade mandrel. 3. CORRECTION 1. Poor cut - ...throttle control in the maintenance section. 2. Check wiring and connections. 5. Obstruction in parts manual. 11. Replace mower drive belt. 3. Wet grass. 3. Replace mower drive belt. 9. Engine speed too slow. 1. Shift to dry before mowing. 4. Replace fuse. Replace blade. Replace with...
Parts Manual
Page 9
...Pulley Idler Flat Lock Nut 3/8-16 Idler V-Groove V-Belt, Drive Pulley Transaxle Shaft Asm. Shift Arm Clevis Rod Shift Spring Shift Spacer Axle Handle Parking Brake Bolt 3/8-16 unc x 2-3/4 Gr. 5 Spacer Retainer Washer Link Clutch Ground Drive Bellcrank Ground Drive Keeper Bellcrank Ground Drive Nut Lock Center 1/4-28 Fnthd Screw 5/16-18... Ga. Retainer Spring Clip Handle Bolt Hex 7/16-14 x 1 Gr. 5 Washer Serrated NOTE: All component dimensions given in U.S. PXT195G42 (96046002200), PRODUCT NO. 960 46 00-22 DRIVE KEY PART NO. NO. 1 -----2 532 12 35-83 15 819 13 13-16 17 532 19 72-97 22 532 19 ...
...Pulley Idler Flat Lock Nut 3/8-16 Idler V-Groove V-Belt, Drive Pulley Transaxle Shaft Asm. Shift Arm Clevis Rod Shift Spring Shift Spacer Axle Handle Parking Brake Bolt 3/8-16 unc x 2-3/4 Gr. 5 Spacer Retainer Washer Link Clutch Ground Drive Bellcrank Ground Drive Keeper Bellcrank Ground Drive Nut Lock Center 1/4-28 Fnthd Screw 5/16-18... Ga. Retainer Spring Clip Handle Bolt Hex 7/16-14 x 1 Gr. 5 Washer Serrated NOTE: All component dimensions given in U.S. PXT195G42 (96046002200), PRODUCT NO. 960 46 00-22 DRIVE KEY PART NO. NO. 1 -----2 532 12 35-83 15 819 13 13-16 17 532 19 72-97 22 532 19 ...