Service Manual
Page 6
... 3-33 History 3-33 MAC 3-33 NVRAM 3-33 NPAP 3-33 TCP/IP 3-33 Paper jams 3-34 Avoiding jams 3-34 Understanding paper jam codes and locations 3-35 200-202 paper jams 3-35 231 paper jam 3-36 233 paper jam 3-37 234 paper jam 3-37 235 paper jam 3-37 242 paper jam 3-38 251... 4-4 ADF cable removal 4-7 ADF input tray removal 4-8 ADF scanner assembly removal 4-9 ADF separator pad removal 4-11 ADF separator roll assembly removal 4-12 Controller board removal 4-13 Cover open sensor removal 4-14 Door mount removal 4-15 vi Service Manual
... 3-33 History 3-33 MAC 3-33 NVRAM 3-33 NPAP 3-33 TCP/IP 3-33 Paper jams 3-34 Avoiding jams 3-34 Understanding paper jam codes and locations 3-35 200-202 paper jams 3-35 231 paper jam 3-36 233 paper jam 3-37 234 paper jam 3-37 235 paper jam 3-37 242 paper jam 3-38 251... 4-4 ADF cable removal 4-7 ADF input tray removal 4-8 ADF scanner assembly removal 4-9 ADF separator pad removal 4-11 ADF separator roll assembly removal 4-12 Controller board removal 4-13 Cover open sensor removal 4-14 Door mount removal 4-15 vi Service Manual
Service Manual
Page 46
... long to the input sensor. Remove the toner cartridge/PC kit, and inspect for any obstructions. See "Main motor service check" on page 4-55. 200.19 The media never reached the input sensor, but did not successfully debounce the sensor. Carefully remove the tray and notice if the leading edge... Possible causes: slow or missing transport motor positional feedback, or the media is loose, then replace it does not rotate freely or is too loose. 200.13 The input sensor is covered when the media is not expected (media in the tray, and replace if they are a small gap or a bouncy manual...
... long to the input sensor. Remove the toner cartridge/PC kit, and inspect for any obstructions. See "Main motor service check" on page 4-55. 200.19 The media never reached the input sensor, but did not successfully debounce the sensor. Carefully remove the tray and notice if the leading edge... Possible causes: slow or missing transport motor positional feedback, or the media is loose, then replace it does not rotate freely or is too loose. 200.13 The input sensor is covered when the media is not expected (media in the tray, and replace if they are a small gap or a bouncy manual...
Service Manual
Page 47
...Verify that the media is that the pick tires are worn. Likely pre staged strips in the tray, and replace if they are worn. 200.33 200.34 Page from tray 1 to declaring MPF source empty. See "ACM pick tire roller removal" on data collection during warm-up. See... "Printhead service check" on page 2-43. 200.37 Timeout on page 4-3. Diagnostics information 2-13 7013-XXX Error Description Action 200.27 Printhead Driver: Mirror motor fell out of lock condition after multiple pick attempts, but the page was later...
...Verify that the media is that the pick tires are worn. Likely pre staged strips in the tray, and replace if they are worn. 200.33 200.34 Page from tray 1 to declaring MPF source empty. See "ACM pick tire roller removal" on data collection during warm-up. See... "Printhead service check" on page 2-43. 200.37 Timeout on page 4-3. Diagnostics information 2-13 7013-XXX Error Description Action 200.27 Printhead Driver: Mirror motor fell out of lock condition after multiple pick attempts, but the page was later...
Service Manual
Page 62
...service check" on . The voltage should be within the following limits: • 100 V ac (volts alternating current)-127 V ac for the 110 V printer • 200 V ac-240 V ac for continuity. • If open, then replace the LVPS/HVPS. • If not open, then check the switch continuity across its conductors...the AC cord from the power supply: Pins Voltage CN201-6, 17, +24 V dc 19 CN201-10, 12, Ground 14, 16, 18 CN201-1,3, 5, +5 V dc 11,13, 15 • If voltages are not correct, then replace the LVPS/HVPS. • If voltages are exposed at several places on . 7013-XXX Dead machine...
...service check" on . The voltage should be within the following limits: • 100 V ac (volts alternating current)-127 V ac for the 110 V printer • 200 V ac-240 V ac for continuity. • If open, then replace the LVPS/HVPS. • If not open, then check the switch continuity across its conductors...the AC cord from the power supply: Pins Voltage CN201-6, 17, +24 V dc 19 CN201-10, 12, Ground 14, 16, 18 CN201-1,3, 5, +5 V dc 11,13, 15 • If voltages are not correct, then replace the LVPS/HVPS. • If voltages are exposed at several places on . 7013-XXX Dead machine...