Service Manual
Page 38
... must be replaced. Note: The Toner Alarm must be turned on in the driver for this message to appear. Action • Press and release Continue to print a photoconductor kit instruction page. • Replace the photoconductor kit. 2-12 Lexmark™ E260, E260d, E260dn Action • Press and release Continue to clear the light sequence and...
... must be replaced. Note: The Toner Alarm must be turned on in the driver for this message to appear. Action • Press and release Continue to print a photoconductor kit instruction page. • Replace the photoconductor kit. 2-12 Lexmark™ E260, E260d, E260dn Action • Press and release Continue to clear the light sequence and...
Service Manual
Page 62
...PC kit. The main input sensor never became uncovered from the sheet ahead. Finally, check the paper size settings in the printer and the driver. 200.03 The video never started to media prestaged in the source tray. perhaps due to expect the printhead mirror motor lock. See "...paper or debric at the input sensor. 200.01 200.02 Classic input jam. See "Diagnostics mode selections" on page 4-39. 2-36 Lexmark™ E260, E260d, E260dn Paper jam error codes (200-series) Repeating jams or jam messages can be resolved. Carefully remove the tray and notice if the leading edge...
...PC kit. The main input sensor never became uncovered from the sheet ahead. Finally, check the paper size settings in the printer and the driver. 200.03 The video never started to media prestaged in the source tray. perhaps due to expect the printhead mirror motor lock. See "...paper or debric at the input sensor. 200.01 200.02 Classic input jam. See "Diagnostics mode selections" on page 4-39. 2-36 Lexmark™ E260, E260d, E260dn Paper jam error codes (200-series) Repeating jams or jam messages can be resolved. Carefully remove the tray and notice if the leading edge...
Service Manual
Page 64
...cable routing for page from tray 1 did make it is dislodged or broken, then repalce the rear exit guide. Retry alignment. 2-38 Lexmark™ E260, E260d, E260dn Timed out waiting for the printhead. Verify that the pick tires are worn. 200.26 The trailing edge never cleared the input sensor when...(There is not enough time since the printhead than the expected stable lock time, but the page was detected during warmup. 200.27 Printhead Driver: Mirror motor fell out of lock condition after media at the input sensor-more than 14 inches too long over the manual feeder sensor....
...cable routing for page from tray 1 did make it is dislodged or broken, then repalce the rear exit guide. Retry alignment. 2-38 Lexmark™ E260, E260d, E260dn Timed out waiting for the printhead. Verify that the pick tires are worn. 200.26 The trailing edge never cleared the input sensor when...(There is not enough time since the printhead than the expected stable lock time, but the page was detected during warmup. 200.27 Printhead Driver: Mirror motor fell out of lock condition after media at the input sensor-more than 14 inches too long over the manual feeder sensor....
Service Manual
Page 74
... Network Buffer Mac Binary PS Std Net Setup USB Menu PCL SmartSwitch PS SmartSwitch NPA Mode USB Buffer Mac Binary PS 2-48 Lexmark™ E260, E260d, E260dn These are accessed through the driver. 4513-200, -220, -230 Diagram of the printer menus Not all menus or selections will be available on all models or...
... Network Buffer Mac Binary PS Std Net Setup USB Menu PCL SmartSwitch PS SmartSwitch NPA Mode USB Buffer Mac Binary PS 2-48 Lexmark™ E260, E260d, E260dn These are accessed through the driver. 4513-200, -220, -230 Diagram of the printer menus Not all menus or selections will be available on all models or...
Service Manual
Page 86
Check the media settings in the printer driver. 2-60 Lexmark™ E260, E260d, E260dn Try a new PC Kit. Place a sheet of image FRU Fuser Media (not a FRU) Action The fuser may not be operating at its ends. Try changing ... a new one. Variation in the left and right transfer roll bearings. Make sure recommended media is not blocked. Check the media settings in the printer driver. A heavier media may have an unbalanced force against the PC (photoconductor) drum. Note: Do not touch the transfer roll except at the proper temperature to...
Check the media settings in the printer driver. 2-60 Lexmark™ E260, E260d, E260dn Try a new PC Kit. Place a sheet of image FRU Fuser Media (not a FRU) Action The fuser may not be operating at its ends. Try changing ... a new one. Variation in the left and right transfer roll bearings. Make sure recommended media is not blocked. Check the media settings in the printer driver. A heavier media may have an unbalanced force against the PC (photoconductor) drum. Note: Do not touch the transfer roll except at the proper temperature to...
Service Manual
Page 90
...8226; Incorrect tray selection or inadequate picking force by unplugging USB and plugging it . • Make sure Tray 1 is selected from the printer driver. If a menu settings page can be printed, then contact the next level of the printer. • Make sure the toner cartridge assembly ... The Load Paper light is on and indicates ready, but nothing prints. Replace card. The Error light alone is installed properly. 2-64 Lexmark™ E260, E260d, E260dn The media fails to on the next command. • Clear all jams. • Press and release , or open and close the ...
...8226; Incorrect tray selection or inadequate picking force by unplugging USB and plugging it . • Make sure Tray 1 is selected from the printer driver. If a menu settings page can be printed, then contact the next level of the printer. • Make sure the toner cartridge assembly ... The Load Paper light is on and indicates ready, but nothing prints. Replace card. The Error light alone is installed properly. 2-64 Lexmark™ E260, E260d, E260dn The media fails to on the next command. • Clear all jams. • Press and release , or open and close the ...