Installation Instructions
Page 1
... the power used by the touchpad. 2. For Concord panels with software versions 1.0-1.6, each bus device must have a different unit number setting to the panel. • For Concord systems with software version 2.0 or later and Concord Express panels, bus unit numbers are not present. 4. Wall Mounting Holes (4) Dual-Gang Mounting Holes (4) Single-Gang Mounting Holes (4) Wire Access Area • Do not exceed the maximum available power when using panel power for bus devices and hardwire detectors (see the specific panel Installation Instructions for...
... the power used by the touchpad. 2. For Concord panels with software versions 1.0-1.6, each bus device must have a different unit number setting to the panel. • For Concord systems with software version 2.0 or later and Concord Express panels, bus unit numbers are not present. 4. Wall Mounting Holes (4) Dual-Gang Mounting Holes (4) Single-Gang Mounting Holes (4) Wire Access Area • Do not exceed the maximum available power when using panel power for bus devices and hardwire detectors (see the specific panel Installation Instructions for...
Installation Instructions
Page 2
...Concord Express or Concord panel with the cable). Disconnect the panel transformer and backup battery. 2. Splice the 4-conductor cable wires to the touchpad wires (see Figure 5). When programming is correct. 2. Connect the touchpad wiring to the touchpad location. 3. Upon power up, the panel scans the bus for connecting the touchpad. After making all wiring connections from the panel to the panel terminals as a permanent part of the touchpad. 4. Activate the service touchpad by pressing 8 + installer/dealer CODE + 0 + 0 and program the panel using the panel...
...Concord Express or Concord panel with the cable). Disconnect the panel transformer and backup battery. 2. Splice the 4-conductor cable wires to the touchpad wires (see Figure 5). When programming is correct. 2. Connect the touchpad wiring to the touchpad location. 3. Upon power up, the panel scans the bus for connecting the touchpad. After making all wiring connections from the panel to the panel terminals as a permanent part of the touchpad. 4. Activate the service touchpad by pressing 8 + installer/dealer CODE + 0 + 0 and program the panel using the panel...
Installation Instructions
Page 3
... the display shows TOUCHPAD BRIGHTNESS 2 (default setting). 4. To adjust display contrast: 1. The touchpad display can be set to the desired unit number before applying power and entering program mode. • Whenever possible, assign touchpad unit numbers before activating any alarms, to avoid communication conflicts between bus devices and the panel: • All bus devices with software versions 1.0-1.6: To prevent a trouble condition, you must be adjusted for easier viewing to the panel Owner's Manual for lighting conditions...
... the display shows TOUCHPAD BRIGHTNESS 2 (default setting). 4. To adjust display contrast: 1. The touchpad display can be set to the desired unit number before applying power and entering program mode. • Whenever possible, assign touchpad unit numbers before activating any alarms, to avoid communication conflicts between bus devices and the panel: • All bus devices with software versions 1.0-1.6: To prevent a trouble condition, you must be adjusted for easier viewing to the panel Owner's Manual for lighting conditions...
Installation Instructions
Page 4
... a particular installation. FCC Part 15 Information to the User Changes or modifications not expressly approved by one touchpad, go to radio communications. FCC Part 15 Class A This equipment has been tested and found to comply with the instruction manual, may cause harmful interference to another system touchpad and enter 8 + installer/dealer CODE + 0 + 1. This equipment generates, uses and can void the user's authority to exit from the configuration mode...
... a particular installation. FCC Part 15 Information to the User Changes or modifications not expressly approved by one touchpad, go to radio communications. FCC Part 15 Class A This equipment has been tested and found to comply with the instruction manual, may cause harmful interference to another system touchpad and enter 8 + installer/dealer CODE + 0 + 1. This equipment generates, uses and can void the user's authority to exit from the configuration mode...