GE 60-804-04 - Concord LCD/VFD Alphanumeric SuperBus Keypad Support and Manuals
Get Help and Manuals for this General Electric item
View All Support Options Below
Free GE 60-804-04 manuals!
Problems with GE 60-804-04?
Ask a Question
Free GE 60-804-04 manuals!
Problems with GE 60-804-04?
Ask a Question
Most Recent GE 60-804-04 Questions
What Kind Of Battery Do I Need For Ge 60-804-04?
The unit beeps (three times?) every 30 seconds. I figure it needs a new battery - I can't even find ...
The unit beeps (three times?) every 30 seconds. I figure it needs a new battery - I can't even find ...
(Posted by sadams70 11 years ago)
How Do You Set Up New User Codes
(Posted by eileen26 13 years ago)
Popular GE 60-804-04 Manual Pages
Installation Instructions - Page 1
... last button press.
Touchpads automatically default to determine where an alarm, trouble, or open-sensor condition exists.
Wire Length
18 (shielded)
1000 Feet...60°C).
Other features include:
Touchpad buttons that require it (see specific panel Installation Instructions).
ITI Part No. 60-804 & 60-810
Document Number: 466-1633 Rev. This eliminates manually setting...
Installation Instructions - Page 2
...
3. Touchpad Mounting Slots
2
SuperBus® 2000 2 x 20 VFD Alphanumeric Touchpad For UL installations with included screws. 5. Separate the mounting bracket from the back-plate by
loosening the two ...Needed
The following must be observed in UL installations
The touchpad hardwire input must not be used for specific wiring instructions.
Secure the back-plate to the matching colored...
Installation Instructions - Page 3
... newerWire a 2K ohm EOL resistor (49-467) in series with normally closed switches and in parallel with software versions 1.0-1.6 - See the UltraGard panel Installation Instructions or Reference Manual for setting the configuration.
3 Make sure the yellow wires are to the left . Note The optional touchpad hardwire input must not be added to the panel...
Installation Instructions - Page 4
... location closest to the left (see specific panel Installation Instructions. If you may proceed with device unit number DIP switches (ESM, HIM, etc.) must be manually changed. Wiring the Touchpad to RUN.
5. Panels automatically assign or learn the unit numbers of the unit.
All partitions must be set to each bus device upon power up...
Installation Instructions - Page 5
...manual configuration mode by pressing ,. After entering the install code, existing touchpads display PROGRAM MODE. Note After entering the install code to switch between the panel and touchpad is correct.
2. Be sure to disconnect each touchpad to enter the install code. All touchpads should show the current system status. Set...status, see "Troubleshooting."
Note Touchpads ...
Installation Instructions - Page 6
.../Unit Numbers from Panel Memory
Please see "Troubleshooting." Adjusting Touchpad Brightness
Please see the specific panel Installation Instructions or User's Manual for the touchpad was previously added (learned)... by pressing ,. Connect the panel battery and plug in the panel transformer. Enter your install access CODE (0123 is the current unit number (000 - 015) for the touchpad.
7. Enter...
Installation Instructions - Page 7
...problems you may be set to each touchpad using the procedure outlined in . Table 3: UltraGard Troubleshooting
Problem
All touchpads display
1.
1 - The panel reports a trouble 1. Set the panel mode switch to PROGRAM, enter the install code, and switch back to RUN.
Set...
2.
Make sure the panel transformer is enrolled. an
error message, or
appears "dead" and 2.
The touchpad ...
Installation Instructions - Page 8
...60-804-01
Advent
60-804-04
Concord, Concord Express
60-810-03-ED
Concord
60-804... in accordance with the instruction manual, may cause harmful interference...specific panel Installation Instructions for complete UL installation requirements for a class A digital device, pursuant to correct the interference by Interactive Technologies, Inc. Operation of the FCC Rules.
FCC Part...
GE 60-804-04 Reviews
We have not received any reviews for GE yet.