Rack-to-Tower Conversion Guide (.pdf)
Page 8
... To connect the SCSI cable to the remaining vertical connector on the 1 x 2 backplane (see Figure 1-3). 4 Attach the end with the 1 x 2 backplane. www.dell.com | support.dell.com NOTICE: The I2C cable must be routed over the top of the cooling shroud. 3 Route the I2C extension cable through the clips on... I2C cable, which was disconnected from the system board in step 1, to the 10-pin I2C connector on redundant array of independent disks (RAID) configurations and the existence of SCSI peripheral cards. Refer to your SCSI devices. NOTE: The four-wire power cable is closest to the...
... To connect the SCSI cable to the remaining vertical connector on the 1 x 2 backplane (see Figure 1-3). 4 Attach the end with the 1 x 2 backplane. www.dell.com | support.dell.com NOTICE: The I2C cable must be routed over the top of the cooling shroud. 3 Route the I2C extension cable through the clips on... I2C cable, which was disconnected from the system board in step 1, to the 10-pin I2C connector on redundant array of independent disks (RAID) configurations and the existence of SCSI peripheral cards. Refer to your SCSI devices. NOTE: The four-wire power cable is closest to the...
SCSI Backplane Daughter Card Installation (.pdf)
Page 1
Dell™ Systems ACTIVATING THE INTEGRATED RAID CONTROLLER www.dell.com support.dell.com
Dell™ Systems ACTIVATING THE INTEGRATED RAID CONTROLLER www.dell.com support.dell.com
SCSI Backplane Daughter Card Installation (.pdf)
Page 3
... off the system and disconnect it from its power source. See the system information label on the RAID controller memory module socket down and outward, as shown in your Dell™ system's integrated PowerEdge™ Expandable RAID 3/Di controller (PERC 3/Di). For You and Your System" in Figure 1-1, which allows you should back up...
... off the system and disconnect it from its power source. See the system information label on the RAID controller memory module socket down and outward, as shown in your Dell™ system's integrated PowerEdge™ Expandable RAID 3/Di controller (PERC 3/Di). For You and Your System" in Figure 1-1, which allows you should back up...
SCSI Backplane Daughter Card Installation (.pdf)
Page 4
... and insert the memory module in its socket on the system board (see Figure 1-1). NOTE: The RAID controller memory module must be an unbuffered memory module, rated to be installed in the socket in the socket. 1-2 Activating... latches on the memory module with your index fingers to lock the memory module into the socket. 8 Install the RAID hardware key in the socket (see Figure 1-2). The socket has two alignment keys that allow the memory module to run... the system cover for system memory. 7 Press on each end of this socket. www.dell.com | support.dell.com Figure 1-1.
... and insert the memory module in its socket on the system board (see Figure 1-1). NOTE: The RAID controller memory module must be an unbuffered memory module, rated to be installed in the socket in the socket. 1-2 Activating... latches on the memory module with your index fingers to lock the memory module into the socket. 8 Install the RAID hardware key in the socket (see Figure 1-2). The socket has two alignment keys that allow the memory module to run... the system cover for system memory. 7 Press on each end of this socket. www.dell.com | support.dell.com Figure 1-1.
SCSI Backplane Daughter Card Installation (.pdf)
Page 5
Figure 1-2. Figure 1-3. Installing the RAID Battery RAID battery Activating the Integrated RAID Controller 1-3 Installing the RAID Hardware Key 9 Install the RAID battery: a Hook the front edge of the RAID battery assembly into the slot near the system board, then snap the clip on the back edge of the battery assembly into place so the battery lies flat (see Figure 1-3).
Figure 1-2. Figure 1-3. Installing the RAID Battery RAID battery Activating the Integrated RAID Controller 1-3 Installing the RAID Hardware Key 9 Install the RAID battery: a Hook the front edge of the RAID battery assembly into the slot near the system board, then snap the clip on the back edge of the battery assembly into place so the battery lies flat (see Figure 1-3).
SCSI Backplane Daughter Card Installation (.pdf)
Page 6
...and Troubleshooting Guide. 10 Replace the cooling shroud and system cover. 11 Reconnect the system and peripherals to the RAID battery connector on the system board (see the RAID controller software documentation provided in this connector). c Install the peripheral bay. For more information, see the system ...information label on . 12 Install the RAID software. www.dell.com | support.dell.com b Connect the battery cable to their power sources and turn them on the inside of the system cover for the...
...and Troubleshooting Guide. 10 Replace the cooling shroud and system cover. 11 Reconnect the system and peripherals to the RAID battery connector on the system board (see the RAID controller software documentation provided in this connector). c Install the peripheral bay. For more information, see the system ...information label on . 12 Install the RAID software. www.dell.com | support.dell.com b Connect the battery cable to their power sources and turn them on the inside of the system cover for the...