System Manual
Page 11
... 810 and 820 of the 2005 National Electrical Code. Also, place Audio/Video (A/V) cables to qualified service personnel. do not operate the DIRECTV® Receiver on a flat, hard surface - TIP: We highly recommend plugging the DIRECTV® Receiver into their jacks. always take ... 26 AWG or better telecommunications line cord. • CAUTION: Replace remote control batteries with care. • Have your components from A/V cables as much as an audio power amplifier. • Protect your DIRECTV® Receiver professionally serviced (do not place vases or other equipment...
... 810 and 820 of the 2005 National Electrical Code. Also, place Audio/Video (A/V) cables to qualified service personnel. do not operate the DIRECTV® Receiver on a flat, hard surface - TIP: We highly recommend plugging the DIRECTV® Receiver into their jacks. always take ... 26 AWG or better telecommunications line cord. • CAUTION: Replace remote control batteries with care. • Have your components from A/V cables as much as an audio power amplifier. • Protect your DIRECTV® Receiver professionally serviced (do not place vases or other equipment...
Installation Guide
Page 4
...DIRECTV Set-Top Box Information for the Installer 5.11 GetReturnValue (0x95)...23 5.12 Reboot (0x96)...23 5.13 SendUserCommand (0xA5)...24 5.14 OpenUserChannel (0xA6) ...25 5.15 GetTuner (0x9A) ...27 5.16 GetPrimaryStatusMT (0x8A) ...28 5.17 GetCurrentChannelMT (0x8B) ...30 5.18 GetSignalQualityMT (0x9D) ...30 5.19 OpenUserChannelMT (0x9F) ...31 6 Remote Control...33 6.1 Introduction ...33 6.2 Brand Setup Code... List ...33 6.3 Remote Control Key Codes...35 7 Wired IR Input Port ...37 7.1 ...
...DIRECTV Set-Top Box Information for the Installer 5.11 GetReturnValue (0x95)...23 5.12 Reboot (0x96)...23 5.13 SendUserCommand (0xA5)...24 5.14 OpenUserChannel (0xA6) ...25 5.15 GetTuner (0x9A) ...27 5.16 GetPrimaryStatusMT (0x8A) ...28 5.17 GetCurrentChannelMT (0x8B) ...30 5.18 GetSignalQualityMT (0x9D) ...30 5.19 OpenUserChannelMT (0x9F) ...31 6 Remote Control...33 6.1 Introduction ...33 6.2 Brand Setup Code... List ...33 6.3 Remote Control Key Codes...35 7 Wired IR Input Port ...37 7.1 ...
Installation Guide
Page 12
...by inputting a channel number (1) This command holds its value after a warm start. DIRECTV Set-Top Box Information for the Installer 4.3 Basic Data Port Commands Table 4-3: Basic Commands Summary Command Code Command Label 0x81 Standby(1) Description Put STB in Standby 0x82 Active Turn STB on ... tuned channel 0x91 GetCurrentTime Current time in UTC 0x92 GetUserCommand Get the remote or front panel command input by the user 0x93 EnableUserEntry Allows direct control of the STB by the remote or front panel buttons 0x94 DisableUserEntry Disables direct control of 42 March...
...by inputting a channel number (1) This command holds its value after a warm start. DIRECTV Set-Top Box Information for the Installer 4.3 Basic Data Port Commands Table 4-3: Basic Commands Summary Command Code Command Label 0x81 Standby(1) Description Put STB in Standby 0x82 Active Turn STB on ... tuned channel 0x91 GetCurrentTime Current time in UTC 0x92 GetUserCommand Get the remote or front panel command input by the user 0x93 EnableUserEntry Allows direct control of the STB by the remote or front panel buttons 0x94 DisableUserEntry Disables direct control of 42 March...
Installation Guide
Page 33
...chapter also provides links pointed to documents that listed the brand setup code used for setting up the remote to the consumer. DIRECTV, Inc. On directv.com, go to control the STB. Version 2.2 Page 33 of DIRECTV remote controls available to control the TV and auxiliary devices. It is...". Find the setup code in the appropriate document. Specific features of DIRECTV remote controls can be found on -line manuals at www.directv.com as noted below The following sections list the DIRECTV remote control key codes for IR emitters used for setting up the remote to control the TV...
...chapter also provides links pointed to documents that listed the brand setup code used for setting up the remote to the consumer. DIRECTV, Inc. On directv.com, go to control the STB. Version 2.2 Page 33 of DIRECTV remote controls available to control the TV and auxiliary devices. It is...". Find the setup code in the appropriate document. Specific features of DIRECTV remote controls can be found on -line manuals at www.directv.com as noted below The following sections list the DIRECTV remote control key codes for IR emitters used for setting up the remote to control the TV...
Installation Guide
Page 35
Version 2.2 Page 35 of 42 March 5, 2008 DTV-MD-0058 DIRECTV Set-Top Box Information for the Installer 6.3 Remote Control Key Codes All DIRECTV Set-top box IR and RF commands are modulated on a 38 kHz carrier. Channel Volume UP Volume Down Mute Guide Info Menu Hex Code Assignment 80h 81h 5Bh(1) 5Bh(1) 10h 5Bh(1) 11h 01h 02h 03h 04h 05h 06h 07h 08h 09h 0Dh 0Eh 0Fh 5Bh(1) 5Bh(1) 5Bh(1) 28h 2Eh 20h DIRECTV, Inc. Key Label STB Power ON STB Power OFF TV Power ON TV Power OFF POWER TV Input Digit 0 Digit 1 Digit 2 Digit 3 Digit 4 Digit 5 Digit 6 Digit 7 Digit 8 Digit 9 CH + CH Prev.
Version 2.2 Page 35 of 42 March 5, 2008 DTV-MD-0058 DIRECTV Set-Top Box Information for the Installer 6.3 Remote Control Key Codes All DIRECTV Set-top box IR and RF commands are modulated on a 38 kHz carrier. Channel Volume UP Volume Down Mute Guide Info Menu Hex Code Assignment 80h 81h 5Bh(1) 5Bh(1) 10h 5Bh(1) 11h 01h 02h 03h 04h 05h 06h 07h 08h 09h 0Dh 0Eh 0Fh 5Bh(1) 5Bh(1) 5Bh(1) 28h 2Eh 20h DIRECTV, Inc. Key Label STB Power ON STB Power OFF TV Power ON TV Power OFF POWER TV Input Digit 0 Digit 1 Digit 2 Digit 3 Digit 4 Digit 5 Digit 6 Digit 7 Digit 8 Digit 9 CH + CH Prev.
