Operation Manual
Page 1
Operator's Manual 1 HP (Maximum Developed) 12 Speeds (250-3100 R.P.M.) 5/8 Inch Chuck 15-INCH DRILL PRESS Model No, 137.229151 CAUTION: Before using this Drill Press, read this manual and follow all its Safety Rules and Operating Instructions • Safety Instructions • Installation • Operation • Maintenance • Parts List • EspaSol Customer Help Line 1-800-843-1682 Sears, Roebuck and Co., Hoffman Estates, Visit our Craftsman website: www.sears.comlcraftsman Part No. 137229151001 IL 60179 USA
Operator's Manual 1 HP (Maximum Developed) 12 Speeds (250-3100 R.P.M.) 5/8 Inch Chuck 15-INCH DRILL PRESS Model No, 137.229151 CAUTION: Before using this Drill Press, read this manual and follow all its Safety Rules and Operating Instructions • Safety Instructions • Installation • Operation • Maintenance • Parts List • EspaSol Customer Help Line 1-800-843-1682 Sears, Roebuck and Co., Hoffman Estates, Visit our Craftsman website: www.sears.comlcraftsman Part No. 137229151001 IL 60179 USA
Operation Manual
Page 14
...(6) on page 15. 1. BELT TENSION (FIG. P) Make sure pulleys are aligned properly as you desire, tighten the standard nut (4) with the screwdriver, engaging the next notch. 5. NOTE: Belt tension is too much play in the lower front notch (1) of the drill press head counterclockwise. ... 1. If there is correct if the belt deflects approximately 1/2 inch when pressed at its lowest position. Lowerthe table for desired speed. 4. Place a screwdriver in the spindle is in Figure R on the drill press head. Tighten the belts by turning clockwise. Loosenthe belts by rotating...
...(6) on page 15. 1. BELT TENSION (FIG. P) Make sure pulleys are aligned properly as you desire, tighten the standard nut (4) with the screwdriver, engaging the next notch. 5. NOTE: Belt tension is too much play in the lower front notch (1) of the drill press head counterclockwise. ... 1. If there is correct if the belt deflects approximately 1/2 inch when pressed at its lowest position. Lowerthe table for desired speed. 4. Place a screwdriver in the spindle is in Figure R on the drill press head. Tighten the belts by turning clockwise. Loosenthe belts by rotating...
Operation Manual
Page 15
.... Fig. Lay the straight edge across the top of the Drill Press. Loosen the motor mount nuts (2). Lift or lower the motor (3) until the belt deflects approximately 1/2 inch when pressed in line. 3. BASIC DRILL PRESS OPEATIONS SPEEDS AND BELT PLACEMENT (FIG. _vlvh_ =1_[I To...clockwise. NOTE: To avoid rattles or other noise, the motor housing should not touch the lower belt guard housing. 4. Q 9 9 9 3100 tr_lin 14 3 15 NOTE: Refer to the chart inside of the head, unlocking the belt tension handle (1). 2. As the machine is in operation. R 9 9 9 250 trim_...
.... Fig. Lay the straight edge across the top of the Drill Press. Loosen the motor mount nuts (2). Lift or lower the motor (3) until the belt deflects approximately 1/2 inch when pressed in line. 3. BASIC DRILL PRESS OPEATIONS SPEEDS AND BELT PLACEMENT (FIG. _vlvh_ =1_[I To...clockwise. NOTE: To avoid rattles or other noise, the motor housing should not touch the lower belt guard housing. 4. Q 9 9 9 3100 tr_lin 14 3 15 NOTE: Refer to the chart inside of the head, unlocking the belt tension handle (1). 2. As the machine is in operation. R 9 9 9 250 trim_...