Craftsman 22901 - Professional 17 in. Drill Press Support and Manuals
Get Help and Manuals for this Craftsman item
View All Support Options Below
Free Craftsman 22901 manuals!
Problems with Craftsman 22901?
Ask a Question
Free Craftsman 22901 manuals!
Problems with Craftsman 22901?
Ask a Question
Popular Craftsman 22901 Manual Pages
Instruction Manual - Page 3
Drill Press with Laser°Trac TM
Motor Specifications: Motor type Continuous duty HP Maximum developedHP Amps
Volts Phase Hertz
R,P,M,
induction 3/4 1=1/2 10/5 120/240 Single 60
1725 (no load)
Product Specifications: Belt Type
Pulley Type
Number of Speeds Drill Speeds
Spindle Taper Chuck Taper Chuck Type Chuck capacity Chuck to Table dimension
Min, Chuck to Table...
Instruction Manual - Page 4
...the Safety and Operating instructions before operating the drill press,
1, READ the entire instruction Manual, LEARN how to ...Sears Retail Stores,
3, ALWAYS WEAR HEARING PROTECTION, Plain cotton is not an acceptable protective device, Hearing equipment should be immediately repaired or replaced...the electrical receptacle when making adjustments, changing parts or performing any way, REMEMBER: Your ...
Instruction Manual - Page 6
...your Drill Press is propedy installed and ...REPLACE A DAMAGED OR WORN CORD IMMEDIATELY. If you are not sure, have the proper eUectdcaU receptacle installed by following the wiring diagram on a circuit that has an electrical receptacle as shown in accordance with a qualified electrician or service personnel if you do not completely understand the grounding instructions...repair or replacement...
Instruction Manual - Page 7
... a bcaU qualified eUectrbian for damage before operating the drill press,
19, REPLACE a damaged cord immediately, DO NOT use any drill press can result in debris being thrown into the ebctrical outlet. READ and understand the instruction manual before servicing, changing bits and cleaning.
9. DO NOT operate this drill press,
17, PROPERLY SUPPORT long or wide workpiece and clamp to the table...
Instruction Manual - Page 8
... use any accessory unless you have completely read the instruction Manual for that can emit laser power up to the drill press, DO NOT STARE INTO BEAM, APERTURE, or into a reflection from a mirror-like surface,
2, AVOID EXPOSURE - AVAILABLE ACCESSORUES
Visit your Sears Hardware Department or see the Craftsman Power and Hand Tool Catalog for the following...
Instruction Manual - Page 15
... chuck, Carefuliy follow the manufacturer's safety rubs concerning its use,
Figure 5-6
K
4, Tighten two set screws (F) on the adjustable handle, one shown on Figure 5-4, Once both are tightened, back off... the jaws are completely recessed inside the chuck, See figure 5-6,
6, Seat the chuck onto the drill press spindle as far as it wiii go, Carefully drive the chuck onto the spindle by placing a ...
Instruction Manual - Page 19
...degrees to the spindle, The table locking bolt then must be tightened,
MAKE CERTAIN the drill press is disconnected from the power source, Sixteen drill speeds (215, 310,340, 450, 490, 510, 600, 675,735, 750, ..., This diagram can also be found on the inside of the belt cover of the drill press,
Figure 11-1
Recommended
Dri|| Press Speeds
6P|H6LE PULLEY
s ,o !so 00IdB0,d I,°00,dy,I0B 0I°...
Instruction Manual - Page 20
... line midway between the puHHeysusing Hightfinger pressure,
6, Tighten both tension lock knobs,
A
C D
1, Insert the drill bit into the chuck and tighten, 2, Place the workpiece on the drill press table, Raise
the drill press table until the workpiece is 1/8-in, from the drill bit, NOTE: Make sure the workpiece is secured to the table properly, 3, Turn the...
Instruction Manual - Page 21
... its upper position when the handHe is reHeased, The return spring was properHy adjusted at the factory, However, to adjust, if necessary:
,, MAKE CERTAIN the drill press is disconnected from the power source,
Figure 14-1
LASER ADJUSTMENTS
,, MAKE CERTAIN the drHHpress is
down, See Figure 15-1,
Figure 15-2
F
D
E
2, While firmHy hoHding the...
Instruction Manual - Page 22
...a verticaU fine scribe (L) into it, This is used to set parafleHsm of the Uasers, See Figure 15-4,
8, Using knob (K),...11, Adjust the drill press table so that it is about 1" under the alignment pin,
12,... wood (M) onto the drill press table under the line pin, See Figure 15-5,
13, Using the drift press feed handle, lower the...mark,
16, Repeat STEPS 14 and 15 to set the right side laser,
17, Move the wood ...
Instruction Manual - Page 23
iNSTALLiNG AND REMOVING DRULL BITS
MAKE CERTAIN the drill press is not possible to support the workpiece against the left side of the drHUbit...you are using a backup board, it is disconnected from the drill press (C), See Figure 18-1,
23 Figure 18-1
SUPPORTING WOF{KPIECE
USE onUyrecommended accessories. if it must be properly supported or clamped. ADJUSTABLE HANDLE Figure 18-1
C
A
B
1, To...
Instruction Manual - Page 26
...drill press unplugged, blow off motor with non-factory parts could cause serious injury to the operator and damage to clean the drill press. Do not allow chips and dust to accumulate under drill press...,
ONLY trained personnel should perform repairs to the drill press, Contact your nearest Sears Service Center for authorized service, Unauthorized repairs or replace° ment with low°...
Instruction Manual - Page 27
... See drill press head and motor assembly in motor for damaged insulation and shorted wires and have them replaced. Have capacitor replaced. 4. NOTE: #3 and #4 must be done by a qualified electrician. inspect terminals in "ASSEMBLY iNSTRUCTiONS".
27 See adjusting spindle return spring in chuck.
1.
Switch key is incorrectly tensioned.
2. Drill bit not properly installed in...
Instruction Manual - Page 28
... Bushing Handle Support MSxlOmm Hex Soc Set Screw Pin 5x26mm... Press
MODELN0.152.229010
Whenservicingu...78 79 80
PART NO.
0R92380 OR92301... Hex Soc Hd Screw
Top Cover Main Housing Switch
Holder
Lasermodub Assy Hose Clamp Alignment Pin Door
Laser Warning Label Padlock Assy (Not Shown) Owner's Manual (Not Shown)
QTY.
1 1
1 2 1 1 1 1
1 1 1 1 2
1 2 1 1
1 1 1 1 2 1
1 1 4 8 4
4 4 1 1
1 1 1 1 1 1
1 1 1...
Instruction Manual - Page 29
Bench Drill Press
{50 (2_. 151 (6)_ 158--_
#
155 (2)_
_g
I_158
45 (2)
/141
_/
140
MODEL N0.152.229010
_5 (4) i
119 (2)
112 114
-%
\49 (2)
52 /
103 (4}_
102 (4)_ i01 {g)_
29 17-in.
Craftsman 22901 Reviews
We have not received any reviews for Craftsman yet.