Craftsman 28129 - Panasonic 21.6V Li-ion Hammer Drill Support and Manuals
Get Help and Manuals for this Craftsman item
This item is in your list!
View All Support Options Below
Free Craftsman 28129 manuals!
Problems with Craftsman 28129?
Ask a Question
Free Craftsman 28129 manuals!
Problems with Craftsman 28129?
Ask a Question
Popular Craftsman 28129 Manual Pages
Operation Manual - Page 1
.... Visit our Craftsman®website: www.sears.com/craftsman
3025736 Certified to CAN/CSA-C22.2 No.745-1,745-2-1 Conforms to UL STD 745-1,745-2-1
Double Insulated
• WARRANTY • SAFETY • UNPACKING • DESCRIPTION • OPERATION • MAINTENANCE Hammer Drill
Model No. 172.28129
CAUTION: Read, understand and follow all Safety Rules and Operating Instructions in . Sears...
Operation Manual - Page 2
..., IL 60179
SAVE THESE INSTRUCTIONS! Warranty Safety Symbols Safety Instructions Unpacking Description Operation Maintenance Accessories Parts List Sears Repair Parts Phone Numbers
Page 2 Page 3 Pages 4-9 Page 10 Pages 11-12 Pages 13-19 Pages 20-22 Page 22 Pages 23-25 Back Cover
ONEYEAR FULL WARRANTY ON CRAFTSMAN PROFESSIONALTOOL If this Craftsman Professional Tool fails due to...
Operation Manual - Page 3
... when practical. Applicable only to install a polarized outlet. This tool is within the voltage marked on another tool. Read the operator's manual carefully. DRESS properly. DO NOT wear loose clothing or jewelry. Proper footing and balance enables better control of parts, and any other practical ways to secure and support the workpiece to a rotating...
Operation Manual - Page 4
... the hammer drill.
3. Tool service must be performed only at a Sears Service Center. Use of electric shock if your Professional Hammer Drill. Drilling into . ELECTRICAL SAFETY cont.
4.
or less in any way; It means attention! ALWAYS carefully inspect the material you are going to follow maintenance instructions may include the following symbols. For this manual.
SERVICE...
Operation Manual - Page 5
Wear safety goggles or other part that is damaged should be properly repaired or replaced at all times. Wear ear protectors when hammering for misalignment or binding of moving parts, breakage of parts, and any other masonry products. • Arsenic and chromium, from this product may contribute to follow all instructions. ALWAYS use only properly positioned, safe, platforms...
Operation Manual - Page 6
... any position for left or right hand use
11. Hammer Drill
[
3. Operator's Manual
z_ WARNING: Do not attempt to have the tool replaced.
,_ WARNING: If any of the parts are damaged or missing (refer to PARTS LIST below), return the saw to your nearest Sears store or Craftsman outlet to modify this tool or create accessories not...
Operation Manual - Page 7
... Speed 0-44,800 / BPM (blows per minute) Impact rate 1/2-in the OFF position when operating the mode selector switch.
/
Fig.4
=
To select the rotary or hammer drilling mode:
=
1. Fig. 3
i NloOwTsEp:Yeeodu umsieg.hDt ohenaort abewhciosntlcinegrneodr; Permanently Lubricated 100% Ball Bearings For smooth operation and long life
17. The...
Operation Manual - Page 8
...and securely install or remove accessory bits using the chuck key provided and the spindle lock on button and the drill will cause the hammer drill to the front of the drill.
To release...(Fig. 5)
The direction of the drill's gear case (see Fig. 7a) and tighten by twisting the handle. Be sure to time for use , durability and long service life.
This reverse position is used to...
Operation Manual - Page 9
.... 4). This will help insure that jaws are free of the chuck. Hammer Drill for loosening.
4. Always use the chuck key. 1. While keeping the button depressed, manually rotate the chuck until the jaws are tight, you to start immediately the next time it . INSTALLING AND REMOVING ACCESSORY BITS (Fig. 11)
You may simply use twist...
Operation Manual - Page 10
... the workpiece, reduce pressure on the hammer drill. 6. Always apply pressure in the chuck. 4. To minimize stalling or breaking through the last part of a drilled hole. A smooth even flow of the hammer drill and bit.
9. bacon grease will cause slower drilling speeds, overheating, and a slower drilling rate. 7. Always unplug the drill when
installing or removing bits and accessories...
Operation Manual - Page 11
... the hammer drill. Insert a 5/16-in the chuck for long life and trouble-free operation. It has been found that the chuck and jaws are well lubricated with an air jet. Use clean damp cloths to electrical tool parts, such as bearings, brushes, commutators, etc.
Using a screwdriver, remove the chuck screw by a qualified service technician...
Operation Manual - Page 12
... Craftsman drill/driver accessories designed for all your drill/driving applications. WARNING: To prevent personal
injury, ALWAYS disconnect the plug from closing. Tap the hex key sharply with a mallet in . Open the chuck jaws, and remove the hex key.
5. Note that are percussion rated, extra long bits, magnetic bit holders and more. Visit your hammer drill...
Operation Manual - Page 13
...200T0080046000A-00
Rubber O-ring
1
4O
200T0250024000A-00
Felt seal
1
41
200W8000063000A-00
Ball bearing(6003-RSZ)
1
24
HAMMER DRILL - MODEL NUMBER 172.28129
Item No.
Part Description
Qty.
101
200T0230009000A-00
Side handle set
1
1
200W2000022000A-00
Bolt
1
2
200T0230007000A-00
Depth ruler
1
3
200T0230006000A-00
handle-sheath
1
4
200T0230008000A-00
handle...
Operation Manual - Page 14
For Sears professional installation of home appliances and items like vacuums, lawn equipment, and electronics, call anytime for the location of carry-in your nearest
Sears Parts & Repair Service Center
1-800-488-1222 (U.S.A.)
www.sears.com
1-800-469-4663 (Canada)
www.sears.ca
To purchase a protection agreement on a product serviced by Sears:
1-800-827-6655 (U.S.A.)
1-800-361...
Craftsman 28129 Reviews
Do you have an experience with the Craftsman 28129 that you would like to share?
Earn 750 points for your review!
We have not received any reviews for Craftsman yet.
Earn 750 points for your review!