Cisco CISCO2504-CH - 2504 Router Support and Manuals
Get Help and Manuals for this Cisco item
View All Support Options Below
Free Cisco CISCO2504-CH manuals!
Problems with Cisco CISCO2504-CH?
Ask a Question
Free Cisco CISCO2504-CH manuals!
Problems with Cisco CISCO2504-CH?
Ask a Question
Popular Cisco CISCO2504-CH Manual Pages
Getting Started Guide - Page 1
GETTING STARTED GUIDE
Cisco 2500 Series Wireless Controller
May 2011 Revised June 2, 2011 1 About This Guide 2 Unpacking and Preparing the Controller for Operation 3 Installing the Controller 4 Running the Bootup Script and Power-On Self Test 5 Logging into the Controller 6 Connecting to the Network 7 What's New in Cisco Product Documentation 8 Translated Safety Warnings
Getting Started Guide - Page 2
... in this guide are in a particular installation. Use the statement number provided at the end of each warning statement. FCC Safety Compliance Statement
This equipment has been tested and found to comply with the instructions, may harm you install and minimally configure your Cisco 2504 Wireless Controller (2504 controller), which is part of the Cisco 2500 Series Wireless Controllers...
Getting Started Guide - Page 3
... access points in an equipment rack, be grounded. The 2504 controller comes with the same or equivalent type recommended by the manufacturer. Replace the battery only with four 4 Gigabit Ethernet ports.
3 Introduction to the Controller
The 2504 controller works in the absence of a suitably installed ground conductor. Dispose of used batteries according to provide system-wide wireless...
Getting Started Guide - Page 4
...LAN link for management software connections
WAN or LAN connection to Cisco 2500 Series Wireless Controllers are not currently supported.
Note Direct connection of how controllers function in a wireless LAN network. The controller has an auto MDI feature, so you should have already designed the wireless topology of your network and have a working knowledge of access points to main office...
Getting Started Guide - Page 5
... WIRELESS CONTROLLER
RESET
Model 2504
1
2
3
4
PWR SYS ALM
RESET
1 2 3-4 POE
PWR ALM
SYS
Table 1 Callout
WLC2504 Front Panel Component Descriptions
Port and LEDs
State and Description
CONSOLE CPU console port
The CPU console port is not available; Figure 2 shows the front panel and location of the allowed values before setting the baud rate. At boot-up the controller configures...
Getting Started Guide - Page 6
...
• Off-No link
2
GigE port and LED
The Gigabit Ethernet port is driven from system reset.
The ports can do not connect access point devices to these ports. This port is designed so that 1500 VAC rms
isolation (per the 802.3 specification) is met between the PSE controller and host CPU TWSI bus #1. This port is designed so that 1500...
Getting Started Guide - Page 9
...
You will need the following items: • One Cisco 2504 Wireless Controller. • One Power supply and power cord (power cord option configurable). • Cisco 2504 Wireless Controller software pre-loaded on the controller (software option configurable). • Optional licenses will be pre-installed on controller at factory, if selected. • Two Number 6 Phillips pan-head...
Getting Started Guide - Page 10
... An SSID can contain up to allow static IP addresses from your wireless LAN or network administrator:
• A system (controller name), such as 10.40.0.5. • A VLAN identifier if the management interface is less convenient, but has higher security and works well for downloading operating system software updates). Note You must enter a username and password and the configured username...
Getting Started Guide - Page 11
... 104° F (0 to the Cisco Wireless LAN Controller Configuration Guide for this installation. Enter help to see a list or refer to 40° C). • Make sure that the controller is more secure and reliable if you are configuring a RADIUS server, such as 10.40.0.3, 1812, and mysecretcode.
• The country code for country code information. This guide is not obstructed. •...
Getting Started Guide - Page 25
... Access Control List Services: ok Starting System Interfaces: ok Starting Client Troubleshooting Service: ok Starting Management Frame Protection: ok Starting Certificate Database: ok Starting VPN Services: ok Starting Licensing Services: ok Starting LWAPP: ok Starting CAPWAP: ok Starting LOCP: ok Starting Security Services: ok
25 All rights reserved. Cisco AireOS Version 7.0.114.76 Firmware...
Getting Started Guide - Page 27
Manually update images
Enter selection:
If you did not press Esc, the boot process continues and takes two to access the following menu:
1. XML config selected Validating XML configuration octeon_device_init: found 1 DPs /dev/fpga: No such device or address readCPUConfigData: cardid 0x6060001 Cisco is a trademark of Cisco Systems, Inc. All rights reserved. Run backup image (7.0.114.75...
Getting Started Guide - Page 31
... the access points use when they have different purposes. All of the mobility group/RF group to which you enter here is assigned to support mobility management, DHCP relay, and embedded Layer 3 security such as 1.1.1.1.
Virtual Gateway IP Address
Enter the IP address of controllers, but they join a controller. The virtual interface is the default SSID that...
Getting Started Guide - Page 33
... no.
If yes is correct.
Enter yes if the configuration entered is entered.
Note The administrative username and password you to log into the controller CLI. Note
This prompt only displays if YES was entered in the "Configure a NTP Server Now?" Table 3
Startup Wizard Information (continued)
Wizard Setting
Enter a polling interval between 3600 and 604800 secs...
Getting Started Guide - Page 35
... configuring the controller to meet the specific needs of access points to the Cisco Wireless LAN Controller Configuration Guide for basic operation.
Note If the link does not activate, check the cable. Note Direct connection of your wireless network.
35 You have configured the controller, use a straight-through ) to connect access that are not currently
supported. The controller...
Getting Started Guide - Page 36
... can use the LED indications to the Cisco Wireless Controller Configuration Guide for a description of the controller becomes active after the controller boots. The installation is available on the front panel of the front panel LEDs. Using the Reset Button
The Reset button on cisco.com. Figure 14 Access Points Connected to the controller console point.
36 See Table 1 on the front panel...
Cisco CISCO2504-CH Reviews
We have not received any reviews for Cisco yet.