Cisco CISCO2514-CH - 2514 Dual Enet/ Serial Router Req Featur Pk Sn Cat4 Support and Manuals
Get Help and Manuals for this Cisco item
View All Support Options Below
Free Cisco CISCO2514-CH manuals!
Problems with Cisco CISCO2514-CH?
Ask a Question
Free Cisco CISCO2514-CH manuals!
Problems with Cisco CISCO2514-CH?
Ask a Question
Popular Cisco CISCO2514-CH Manual Pages
Getting Started Guide - Page 3
... the equipment in increments of services for mobility services such as voice and video, and OEAP support for retail, enterprise branches, and small and medium-sized businesses.
The 2504 controller comes with the same or equivalent type recommended by the manufacturer. Warning
There is the danger of used batteries according to the manufacturer's instructions.
Getting Started Guide - Page 4
...delivers unprecedented reliability using 802.11n with Cisco Next-Generation Wireless Solutions and Cisco Enterprise Wireless Mesh. To best use this guide, you can use straight-through or crossover cables. Figure 1 shows a 2504 controller network topology and network connections, showing the medium dependent interface (MDI) Ethernet cables required. Figure 1 Typical Controller Topology and Network...
Getting Started Guide - Page 5
...
CISCO 2500 Series WIRELESS CONTROLLER
RESET
Model 2504
1
2
3
4
PWR SYS ALM
RESET
1 2 3-4 POE
PWR ALM
SYS
Table 1 Callout
WLC2504 Front Panel Component Descriptions
Port and LEDs
State and Description
CONSOLE CPU console port
The CPU console port is an RS-232 port that the stored baud rate setting matches one of the LED manufacturer's specifications...
Getting Started Guide - Page 9
... supply and power cord (power cord option configurable). • Cisco 2504 Wireless Controller software pre-loaded on a desk, shelf, or wall. • Two wall anchors. • Strain relief clip and screw. • Optional hardware will need the following tools and information before you can install the controller: • Wireless controller hardware - Null modem...
Getting Started Guide - Page 11
... equipment connected to the 10/100/1000
Mb/s Ethernet ports. • Make sure that the power cord can install the controller almost anywhere, but it is more...Cisco Wireless LAN Controller Configuration Guide for this installation. This guide is available at least 4 in a secure equipment room or wiring closet. • RADIUS server IP address, communications port, and secret if you install...
Getting Started Guide - Page 13
... using the CLI setup program, see the "Running the Bootup Script and Power-On Self Test" section on the table or shelf near an AC power source. Failure to use the correct hardware or to the Network
For configuration instructions about using rack-mount brackets, follow the correct procedures could result in the kit...
Getting Started Guide - Page 18
... shown in Figure 9 with stabilizing devices, install the stabilizers before mounting or servicing the unit in the rack.
Mounting the ....
Step 1 Attach the 19-inch brackets to ensure your safety:
• This unit should be mounted at the bottom... 6 For configuration instructions about using the CLI setup program, see the "Running the Bootup Script and Power-On Self Test" section on page...
Getting Started Guide - Page 21
...Cable
To secure the power adapter cable to the console port.
To secure the power adapter cable and plug, follow these steps:
21
Before you can be damaged if the power cable is not compatible with the cable. Note The Cisco... Port
Caution
Do not connect a Power over Ethernet (PoE) cable to the 2504 controller, use the plastic relief clip shipped with a 2504 controller.
Getting Started Guide - Page 25
... 1 Initialization: ok Fastpath CPU00: Initializing Timer...done. Flags-[DUTY CYCLE] : ok Fastpath CPU00: Initializing last packet received queue. Num of Cisco Systems, Inc. Installing ether-pow driver - 0x6008 starting pid 805, tty '/dev/ttyS0': '/usr/bin/gettyOrMwar' Cryptographic library self-test....passed! XML config selected Validating XML configuration octeon_device_init: found 1 DPs...
Getting Started Guide - Page 27
.... Clear configuration 5. Format FLASH Drive 6. Software Copyright Cisco Systems, Inc. All rights reserved. Installing ether-pow driver - 0x6008 starting pid 672, tty '': '/etc/init.d/rcS' type = block dump-device = 254:4 disrupt level = header compress = none ifconfig: SIOCGIFFLAGS: No such device Detecting Hardware ... Manually update images
Enter selection:
If you did not press...
Getting Started Guide - Page 31
..., but they join a controller.
Network Name (SSID)
Enter the network name, or service set identifier (SSID). Values are not identical. Both groups define clusters of the mobility group/RF group to which you enter here is assigned to support mobility management, DHCP relay, and embedded Layer 3 security such as 1.1.1.1. All of the controller virtual...
Getting Started Guide - Page 34
... Ethernet (RJ-45 physical port, UTP, Category-5 or higher cable). For example, to 160 minutes using double quotation marks. Always use Category-5, Category-5e, Category-6, or Category-7 Ethernet cables ...minutes of inactivity. You can change the system prompt to the controller.
You can set the automatic logout from the network (802.11 distribution system) to CISCO2504, enter config...
Getting Started Guide - Page 35
...Category-7 Ethernet cables to connect up to 50 Cisco lightweight access points to the controller Ethernet ports or to the network (distribution system) as the controller is operational, the controller is available to Cisco 2500 Series Wireless ... clients to meet the specific needs of access points to connect access that are not currently
supported. Note If the link does not activate, check ...
Getting Started Guide - Page 37
The RSS feeds are a free service and Cisco currently supports RSS Version 2.0.
37 After the controller reboots, enter your desktop using a pointed object, such as a Really Simple Syndication (RSS) feed and set content to be delivered directly to your username and password at : http://www.cisco.com/en/US/docs/general/whatsnew/whatsnew.html Subscribe to the...
Getting Started Guide - Page 55
...the provided or designated connection cables/power cables/AC adaptors/batteries. Statement 157-VCCI Compliance for Class B Equipment
Warning
This is used near a radio or television receiver in a domestic environment, it may cause radio interference.
Statement 371-Power Cable and AC Adapter
When installing the product, please use the equipment according to the instruction manual.
55
Cisco CISCO2514-CH Reviews
We have not received any reviews for Cisco yet.