Cisco GSR8/10-40-UPG= - 12008 Router -AnyLAN, Serial Support and Manuals
Get Help and Manuals for this Cisco item
This item is in your list!
View All Support Options Below
Free Cisco GSR8/10-40-UPG= manuals!
Problems with Cisco GSR8/10-40-UPG=?
Ask a Question
Free Cisco GSR8/10-40-UPG= manuals!
Problems with Cisco GSR8/10-40-UPG=?
Ask a Question
Popular Cisco GSR8/10-40-UPG= Manual Pages
Configuration Guide - Page 9
... Card 4-55 Copying Cisco IOS Software Images between Flash Memory Cards 4-57 Copying System Configuration Files between RP Memory and a Flash Memory Card 4-59 Recovering from Locked Blocks in Flash Memory Cards 4-63
What to Do Next? 4-64
If You Need More Configuration Information 4-64
Troubleshooting the Installation 5-1
Troubleshooting Overview 5-2 Normal System Status at Startup 5-2 Problem...
Configuration Guide - Page 19
... than printed documentation. Ordering Documentation
Registered CCO users can
About This Guide xix This highly integrated Internet application is the foundation of a suite of features and services helps customers and partners to Cisco. Through CCO, you will find information about Cisco and our networking solutions, services, and programs. In addition, you can order the Documentation CD...
Configuration Guide - Page 196
... your network plan.
4-12 Cisco 12008 Gigabit Switch Router Installation and Configuration Guide At initial startup of manually configuring your router. the premise for your router, you through an interactive script that minimizes the likelihood of the following methods:
• Method 1-Using the setup facility or the setup command. The advantage in the section entitled "Using the Setup...
Configuration Guide - Page 204
... interface configuration information for the RP and installed line cards, you need the following information:
• Interface network addresses • Subnet masks • Protocols to the configuration note that shipped with external networks. To configure the interface parameters for the RP and each card.
4-20 Cisco 12008 Gigabit Switch Router Installation and Configuration Guide
Configuration Guide - Page 231
... Tasks
• Copying Files to a Flash Memory Medium • Copying a Cisco IOS Software Image onto a Flash Memory Card • Copying Cisco IOS Software Images between Flash Memory Cards • Copying System Configuration Files between RP Memory and a Flash Memory Card • Recovering from Locked Blocks in Flash Memory Cards
Installing and Removing a Flash Memory Card in an antistatic...
Configuration Guide - Page 240
... Gigabit Switch Router Installation and Configuration Guide
To copy a bootable image onto a Flash memory card, perform the following command:
Router# copy tftp:new.image slot0:new.image 20575008 bytes available on device slot0, proceed? [confirm] Address or name of a configured and fully
functional network interface on using the setup command facility.
For instructions on your...
Configuration Guide - Page 242
... image between Flash memory cards, perform the following command to copy the file image.new in slot 1 to designate the file image.new as the new default Cisco IOS software boot image. Step 2 Enable the router to the old image it already contains).
4-58 Cisco 12008 Gigabit Switch Router Installation and Configuration Guide Note Take this step...
Configuration Guide - Page 243
...:image.new slot0:
Step 5
In the latter case, the name of the file is booted from a Flash Memory Card to a TFTP server on which you do not have access to NVRAM
Observing ...completes the procedure for copying a bootable image between RP Memory and a Flash Memory Card Copying a configuration file to a Flash memory card inserted in PCMCIA slot 0 or slot 1 might be required if you can also...
Configuration Guide - Page 245
... the following form:
copy startup-config [slot0: | slot1: ]:filename
where: copy startup-config specifies the source file to be copied (the Flash memory card inserted in slot 0, issue the directory command:
Router# dir slot0:
-#- -length- -----date/time------ Step 3
To further verify that the file has been copied correctly. The CRC verifies that the configuration...
Configuration Guide - Page 282
... and fully operational. To remove or replace the air filter, perform the following steps:
Step 1
Using both hands, exert upward pressure on the two lower spring clips (see Figure 7-1). Set the bezel aside temporarily.
7-2 Cisco 12008 Gigabit Switch Router Installation and Configuration Guide
The EMI frame is the only part that they have a shelf life of...
Configuration Guide - Page 302
... depends on the DC-input power supply faceplate. Set the voltmeter to support its weight.
7-22 Cisco 12008 Gigabit Switch Router Installation and Configuration Guide Make certain that makes it for negative (-).
remove the filler panel and retain it capable of the new power supply that will service the DC-input power supply; Grasp the carrying...
Configuration Guide - Page 304
... shield
Step 9 Unscrew the loosely mounted lock washers and nuts from the standoffs and set this hardware aside temporarily.
7-24 Cisco 12008 Gigabit Switch Router Installation and Configuration Guide
Figure 7-7
Plastic Safety Shield on the power supply faceplate;
Adding, Removing, or Replacing a DC-Input Power Supply
(b) Grasp the safety shield and move it to the...
Configuration Guide - Page 353
Maintaining the Cisco 12008 7-73 Install the top trim piece onto the chassis by pushing it onto the chassis fasteners (see Figure 7-25, part 2). Removing and Replacing the Cable Management System Figure 7-25 Installing a Cable Management Tray
2
Installation screws
1 3
EJECT
SSLLOOTT--01
RESET AUX
Alarm Alarm
ACO/LT ACO/LT
CONSOLE
CriticaMl ajor Minor Alarms CriticaMl ajor...
Configuration Guide - Page 363
... router, perform the following steps:
(a) Loosen the two captive installation screws at the top and bottom of line cards;
Maintaining the Cisco 12008 7-83 The router supports online insertion and removal (OIR) of the line card faceplate (see Figure 7-32b).
To remove a line card from the line card and hook it in the cutout located on an...
Configuration Guide - Page 380
...-input power supply 3-9, 3-16 RP 7-52 upper card cage cards 3-7 replacing air filter 7-3 RP 7-55 upper card cage cards 3-14 system configuration, basic 4-13 to 4-30 startup 4-4 to 4-11 using configuration mode 4-26 to 4-27 processor CPU on the GRP 1-27 CPU on the PRP 1-35 line card 5-12
Index 6
Cisco 12008 Gigabit Switch Router Installation and Configuration Guide
Cisco GSR8/10-40-UPG= Reviews
Do you have an experience with the Cisco GSR8/10-40-UPG= that you would like to share?
Earn 750 points for your review!
We have not received any reviews for Cisco yet.
Earn 750 points for your review!