Cisco GSR12/60 - 12012 Router -AnyLAN, SONET/SDH Support and Manuals
Get Help and Manuals for this Cisco item
View All Support Options Below
Free Cisco GSR12/60 manuals!
Problems with Cisco GSR12/60?
Ask a Question
Free Cisco GSR12/60 manuals!
Problems with Cisco GSR12/60?
Ask a Question
Popular Cisco GSR12/60 Manual Pages
Installation Guide - Page 8
... 4-7
Configuring the Cisco 12012 4-8 Performing a Basic Manual Configuration Using the Setup Facility or the setup Command 4-8 Configuring the Global Parameters 4-9 Configuring Interfaces 4-15 Performing a Basic Configuration Using Configuration Mode 4-20 Checking the Running Configuration Settings before Saving Them 4-21 Saving the Running Configuration Settings and Reviewing Your Configuration...
Installation Guide - Page 47
... batteries that you to remotely load and store multiple Cisco IOS software and microcode images. You then can download a new image over the network or from any of 5 years. You can boot the routers either manually or automatically from a local server and then add the new image to Flash memory or replace the existing files. Table 1-4
Supported...
Installation Guide - Page 127
... cards with multiple ports only), identify the network interface cable that connects to each line card port. Avoid any kinks...Connecting Line Card Cables
Step 4 Step 5 Step 6
Proceeding from bottom port to the top port (on line cards with multiple ports only), carefully press the network... interface cable into the rest of the line card interface cables. Note Adjust the network ...
Installation Guide - Page 174
...The Simple Network Management Protocol (SNMP) is transmitted. It provides a means to monitor and control network elements. (For complete information on your console terminal.
4-14 Cisco 12012 Gigabit Switch Router Installation and Configuration Guide SNMP defines a set configuration and run-time parameters of functions that can be established before data is the most widely supported open...
Installation Guide - Page 203
For instructions on using this facility, refer to the section "Performing a Basic Manual Configuration Using the Setup Facility or the setup Command," earlier in slot 0, using the setup command facility.
Observing System Startup and Performing a Basic Configuration 4-43
Step 2 Enable the router and copy the image new.image to the Flash memory card in this server
To...
Installation Guide - Page 206
...from NVRAM) or your configuration file. Note that the environmental variable CONFIG_FILE is set ) to NVRAM, which you can then copy the configuration file back to ... [ slot0: | slot1: ]:filename for NVRAM, by default.
4-46 Cisco 12012 Gigabit Switch Router Installation and Configuration Guide Implementing Other Configuration Tasks
Copying System Configuration Files Between RP Memory and a ...
Installation Guide - Page 241
... - CHAPTER 7
Maintaining the Cisco 12012
After you install and configure your Cisco 12012, you might need to upgrade your system, add components, replace components, or change , you might need to perform specific maintenance procedures and operations to ensure that the router continues to operate properly, to upgrade specific system components or replace field replaceable units (FRUs).
Installation Guide - Page 244
.... 7-4 Cisco 12012 Gigabit Switch Router Installation and Configuration Guide
Connecting an ESD-Preventive Strap to the Cisco 12012
OOOOOOOOOOOOOOOOOOOOOOOOOOOOOOOOOOOOOOOOOOOOOOOOOOOOOOOOOOOOOOOOOOOOOOOOOOOOOOOOOOOOOOOOOOOOOO 46596
CRITICALMAJORMINOR
ALARM 1 ACO/LT
ALARM 2
FAIL ENABLED 0
CSC 10
SFC
12 ALARM
ESD connection
socket
Figure 7-1
Cleaning and Replacing the Air Filter Assembly...
Installation Guide - Page 255
Note We recommend attaching each AC-input power supply to upgrade your site. Use two hands when handling the power supply. Installing a New or Replacement AC-Input Power Supply
If you can install the power supply without removing power from the system.
Removing and Replacing an AC-Input Power Supply
Caution The AC-input power supply...
Installation Guide - Page 259
... supply. Note If you are upgrading your wrist and to the DC-input power supply. These parts are available commercially. (For details on the frame. they are not available from Cisco Systems;
Removing and Replacing a DC-Input Power Supply
Removing and Replacing a DC-Input Power Supply
The Cisco 12012 supports up to install or replace a DC-input power supply...
Installation Guide - Page 265
... 60-amp service is dependent on a piece of lug. Maintaining the Cisco 12012 7-25 Step 11 If leads are attached to prevent accidental contact between the leads, or the leads and ground.
Removing and Replacing a DC-Input Power Supply
Step 10 Pull the DC power cable leads down through the power supply handle and set...
Installation Guide - Page 266
... secure the source DC power cable bracket to the power supply faceplate and remove the bracket.
7-26 Cisco 12012 Gigabit Switch Router Installation and Configuration Guide Caution The DC-input power supply weighs 19 lb (8.3 kg). Removing and Replacing a DC-Input Power Supply
Figure 7-12 DC Power Cable Lug
End View
2.25
All measurements in...
Installation Guide - Page 281
... Step 1 and Step 2 for a second system grounding connection. Replacing the Power Supplies
If your system is configured with fewer than four AC-input power supplies or only one DC-input power supply installed, power supply blanks must be installed in a Cisco 12012 system with AC-input power supplies, install the power supplies according to the card...
Installation Guide - Page 300
... 3-51 Connectionless Network Service See CLNS, configuring connections, checking 4-2 connector alarm card external alarm 3-48 auxiliary port 3-35, 3-42 console port 3-35, 3-42 Ethernet 3-37, 3-40 console port connecting devices to 3-33, 3-40 description 1-12, 1-22 pinout 3-35, 3-42 settings 3-34, 4-30 cooling subsystem components 5-15 environmental shutdown 5-17 troubleshooting 5-15 copy command...
Installation Guide - Page 308
... subsystem 5-15 damaged power cord 5-8 environmental shutdown 5-17 line card problems 5-12 power problems 5-4 processor subsystem 5-10 RP 5-10 startup problems 5-4 twisted-pair wiring 2-16
U
uninterruptible power source See UPS
unpacking, system 2-23 upgrading
for redundancy AC-input power 7-15 DC-input power 7-19, 7-25
12 Cisco 12012 Gigabit Switch Router Installation and Configuration Guide
Cisco GSR12/60 Reviews
We have not received any reviews for Cisco yet.