Cisco CISCO2520-CH - 2520 Router Support and Manuals
Get Help and Manuals for this Cisco item
View All Support Options Below
Free Cisco CISCO2520-CH manuals!
Problems with Cisco CISCO2520-CH?
Ask a Question
Free Cisco CISCO2520-CH manuals!
Problems with Cisco CISCO2520-CH?
Ask a Question
Popular Cisco CISCO2520-CH Manual Pages
Getting Started Guide - Page 5
...
Model 2504
1
2
3
4
PWR SYS ALM
RESET
1 2 3-4 POE
PWR ALM
SYS
Table 1 Callout
WLC2504 Front Panel Component Descriptions
Port and LEDs
State and Description
CONSOLE CPU console port
The CPU console port is expected that the stored baud rate setting matches one of the front panel. A default baud-rate recovery mechanism is not a defect.
At boot-up the controller configures...
Getting Started Guide - Page 6
... and any 48V/Ethernet signal. LED description:
• Green or Blinking Green-Link activity
• Off-No link
3 & 4 POE GigE Power-over I2C.
This port is designed so that 1500 VAC rms
isolation (per the 802.3 specification) is configured to these ports. They provide a I2C communications channel between the PSE controller and host CPU TWSI bus #1.
Getting Started Guide - Page 9
... the following tools and information before you can install the controller: • Wireless controller hardware - If any item is damaged or missing, notify your authorized Cisco sales representative. Network, operating system service network, and access point cables as required • Command-line interface (CLI) console - Controller with factory-supplied power cord and mounting hardware -
Getting Started Guide - Page 11
... Power Adapter Cable, page 21 • Installing a Security Lock, page 23
Mounting the Controller
This section includes the following these guidelines:
• Make sure you are configuring a RADIUS server, such as 10.40.0.3, 1812, and mysecretcode.
• The country code for country code information. Enter help to see a list or refer to the Cisco Wireless LAN Controller Configuration Guide...
Getting Started Guide - Page 13
...installation:
• Connecting the Controller Console Port • Securing the Power Adapter Cable • Connecting to the Network
For configuration instructions about using the CLI setup program, see the "Running the Bootup Script and Power...before beginning installation. Note...switch on a wall using rack-mount brackets, follow the correct procedures could result in the kit.
13 The kit part...
Getting Started Guide - Page 18
... in Figure 9 with stabilizing devices, install the stabilizers before mounting or servicing the unit in the rack. Warning
To prevent bodily injury when mounting or servicing this unit in a rack, you can... that the system remains stable. Step 6 For configuration instructions about using the CLI setup program, see the "Running the Bootup Script and Power-On Self Test" section on page 23.
Getting Started Guide - Page 23
... back of the controller code, press Esc when the boot loader prompt appears. The Bootloader Options menu appears. Refer to 240 VAC, 50-60 Hz electrical outlet. To run a previous release of the controller.
You can install an optional customer-supplied cable lock, such as described in the "Connecting the Controller Console Port" section on page...
Getting Started Guide - Page 24
... the controller until the user login prompt appears.
Manually update images Enter selection:
If you did not press Esc, the boot process continues and takes two to access the Boot Menu... Environment MAC address override CF Bus 0 (IDE): OK IDE device 0: - Format FLASH Drive 6. Clear configuration 5.
Capacity: 977.4 MB = 0.9 GB (2001888 x 512) Press now...
Getting Started Guide - Page 25
... last packet received queue. Installing ether-pow driver - 0x6008 starting pid 805, tty '/dev/ttyS0': '/usr/bin/gettyOrMwar' Cryptographic library self-test....passed! Software Copyright Cisco Systems, Inc. Starting Switching Services: ok Starting QoS Services: ok Starting Policy Manager: ok Starting Data Transport Link Layer: ok Starting Access Control List Services: ok Starting System...
Getting Started Guide - Page 26
... Director: ok Starting Network Time Services: ok Starting Cisco Discovery Protocol: ok Starting Broadcast Services: ok Starting Logging Services: ok Starting DHCP Server: ok Starting IDS Signature Manager: ok Starting RFID Tag Tracking: ok Starting Power Supply and Fan Status Monitoring Service: ok Starting Mesh Services: ok Starting TSM: ok Starting CIDS Services: ok Starting Ethernet-over-IP...
Getting Started Guide - Page 27
...: ok Starting Fastpath Console redirect : ok
27 Installing ether-pow driver - 0x6008 starting pid 672, tty '': '/etc/init.d/rcS' type = block dump-device = 254:4 disrupt level = header compress = none ifconfig: SIOCGIFFLAGS: No such device Detecting Hardware ... Software Copyright Cisco Systems, Inc. Run backup image (7.0.114.75) 3. Clear configuration 5. Loading primary image...
Getting Started Guide - Page 28
... Director: ok Starting Network Time Services: ok Starting Cisco Discovery Protocol: ok Starting Broadcast Services: ok Starting Logging Services: ok Starting DHCP Server: ok Starting IDS Signature Manager: ok Starting RFID Tag Tracking: ok Starting Power Supply and Fan Status Monitoring Service: ok Starting Mesh Services: ok Starting TSM: ok Starting CIDS Services: ok Starting Ethernet-over-IP...
Getting Started Guide - Page 30
... assigned to match the switch interface configuration. Enter the administrative password to be set to this controller. You can enter from 3 to the controller.
Enter the IP address of the management interface. Management Interface IP Address
Management Interface Netmask Management Interface Default Router Management Interface VLAN Identifier
Management Interface Port Num [1 to 4]
Note...
Getting Started Guide - Page 35
... address in Figure 14. Refer to the Cisco Wireless LAN Controller Configuration Guide for information on configuring the controller to make the connections. The controller has an auto MDI feature, so you can use a straight-through ) to meet the specific needs of access points to connect access that are not currently
supported. When you have prepared the controller...
Getting Started Guide - Page 36
... Controller Configuration Guide for a description of the unit. To reset the controller using the Reset button, follow these steps:
Step 1 Connect a PC to quickly assess the status of the front panel LEDs. Figure 14 Access Points Connected to a Controller
Network
Cisco 2504 Wireless Controller
10/100/1000BASE-T MDI cable
Network
10/100/1000BASE-T MDI cables
282081
Cisco Access...
Cisco CISCO2520-CH Reviews
We have not received any reviews for Cisco yet.