Hardware Installation Guide
Page 146
... the WIC-4ESW interface card. On the Cisco 1751 router and the Cisco 1760 router, the Fast Ethernet interfaces on the features of VLANs supported by interface type, slot number, a forward slash (/), and the port number. Although the router supports more VLANs, the WIC-4ESW interface card supports a maximum of the router. Additional information on WIC-4ESW are...
... the WIC-4ESW interface card. On the Cisco 1751 router and the Cisco 1760 router, the Fast Ethernet interfaces on the features of VLANs supported by interface type, slot number, a forward slash (/), and the port number. Although the router supports more VLANs, the WIC-4ESW interface card supports a maximum of the router. Additional information on WIC-4ESW are...
Hardware Installation Guide
Page 147
...WIC-4ESW Interface Card Platform Limitations The following features are not supported on the WIC-4ESW interface card: • Virtual Local Area Network (VLAN) trunking protocols (server and client modes, and transparent mode v2) • Spanning Tree Protocol (STP) backbone fast • STP ...or multicast flooding • Multicast groups • IP multicast support • Cisco Group Management Protocol (CGMP) client, CGMP fast-leave • Dynamic access ports • Dynamic trunk protocol • Dynamic VLANs OL-12849-01 3 WIC-4ESW Interface Card Supported Standards The WIC-4ESW ...
...WIC-4ESW Interface Card Platform Limitations The following features are not supported on the WIC-4ESW interface card: • Virtual Local Area Network (VLAN) trunking protocols (server and client modes, and transparent mode v2) • Spanning Tree Protocol (STP) backbone fast • STP ...or multicast flooding • Multicast groups • IP multicast support • Cisco Group Management Protocol (CGMP) client, CGMP fast-leave • Dynamic access ports • Dynamic trunk protocol • Dynamic VLANs OL-12849-01 3 WIC-4ESW Interface Card Supported Standards The WIC-4ESW ...
Hardware Installation Guide
Page 148
... Interface Card LED The LNK (physical layer link) LED is on when the port is up. The FDX LED is on when the Cisco IOS software recognizes the WIC-1ENET card and the connection is operating in full-duplex mode, and off when operating in half-duplex mode....-12849-01 4 Additionally, the Activity LED on the front of the router indicates that data is being transmitted or received on -board switching • Monitoring of VLANs • Multi-VLAN ports network port • Shared STP instances • VLAN-based SPAN • VLAN Query Protocol (VQP) • VTP pruning protocol • Web-based...
... Interface Card LED The LNK (physical layer link) LED is on when the port is up. The FDX LED is on when the Cisco IOS software recognizes the WIC-1ENET card and the connection is operating in full-duplex mode, and off when operating in half-duplex mode....-12849-01 4 Additionally, the Activity LED on the front of the router indicates that data is being transmitted or received on -board switching • Monitoring of VLANs • Multi-VLAN ports network port • Shared STP instances • VLAN-based SPAN • VLAN Query Protocol (VQP) • VTP pruning protocol • Web-based...
Hardware Installation Guide
Page 154
...and any other platform interfaces. The HWIC also supports Layer 3 traffic to fit into HWIC slots only. Note In order for traffic between different VLANs on page 7 for a description of the other port on the HWIC and any of these LEDs. Figure 109 HWIC-4ESW Faceplate 95786 HWIC ...provide power to an IP phone or to a wireless access point attached to distribute inline power, the router must be provisioned with an optional -48 volt power supply. Each version of the Cisco 10/100BASE-T Ethernet switch HWIC is intended to the ports of inline power through 7. The ninth port...
...and any other platform interfaces. The HWIC also supports Layer 3 traffic to fit into HWIC slots only. Note In order for traffic between different VLANs on page 7 for a description of the other port on the HWIC and any of these LEDs. Figure 109 HWIC-4ESW Faceplate 95786 HWIC ...provide power to an IP phone or to a wireless access point attached to distribute inline power, the router must be provisioned with an optional -48 volt power supply. Each version of the Cisco 10/100BASE-T Ethernet switch HWIC is intended to the ports of inline power through 7. The ninth port...