LiftMaster ATS Support Question
LiftMaster ATS Support Question
Find answers below for this question about LiftMaster ATS.Need a LiftMaster ATS manual? We have 1 online manual for this item!
Question posted by vicnrose1 on May 21st, 2013
Ats 211 Model (purchase A Year Ago).
The switch mounted by the door will not open the garage door. All that is heard when the switch is presses, is a clicking sound. The remote sensor in the family cr works fine wi no issues. Is there any resetting or advice to make the switch trigger the door to open?
Current Answers
Related LiftMaster ATS Manual Pages
ATS2113X Manual - Page 1
... enclosed safety materials carefully! ■ Fasten the manual near the garage door after installation. ■ The door WILL NOT CLOSE unless the Protector System® is connected and properly
aligned. ■ Periodic checks of the opener are required to ensure safe operation. ■ The model number label is located on the front panel of your...
ATS2113X Manual - Page 2
... Test the Protector System 23
Operation
24-28
Operation safety instructions 24 Using your garage door opener 24 Using the wall-mounted door control 25 To open the door manually 25 Care of your garage door opener 26 Having a problem 27-28
Programming
29-31
3-Button remote controls (Optional 29 To add or change a Keyless Entry PIN (Optional 30 Multi-Function...
ATS2113X Manual - Page 3
....
• This product is out of which are under EXTREME tension.
• Disable ALL locks and remove ALL ropes connected to garage door BEFORE installing and operating garage door opener to loosen, move or adjust garage door, door springs, cables, pulleys, brackets or their hardware, ALL of balance.
If balanced, it should stay in . lb/sec.
8 Cycles per...
ATS2113X Manual - Page 4
... OR
Torsion Spring
Access Door
Wall-Mounted Door Control
Safety Reversing Sensor
Gap between the bottom of door must not exceed 1/4" (6 mm). Slack in chain tension is normal when garage door is required. You may NOT work properly.
• The floor or the garage door MUST be repaired to your garage door. See page 19 for lightweight garage doors (fiberglass, steel, aluminum...
ATS2113X Manual - Page 5
...
Your garage door opener is packaged in two cartons which contain the motor unit and all parts illustrated below . Hardware for Safety Reversing Sensor Lag Screw 1/4"x1-1/2" (4) Carriage Bolt 1/4"-20x1/2" (4) Lock Nut 1/4"-20 (4) Wing Nut (2) Hex Screw 1/4"-20x1-1/2" (2) Screw #10-32x3/8" (4) Lock Nut #10x32 (4) Insulated Staples (20)
5 Accessories will depend on the model purchased. Parts...
ATS2113X Manual - Page 6
... to the Motor Unit
To avoid installation difficulties, do not run the garage door opener until instructed to do so. • Place the opener on packing material to protect the
cover. • Remove the (2) 5/16"-18x1/2" washered bolts mounted
in the top of the motor unit. • Position rail at a 45° angle...
ATS2113X Manual - Page 7
... reverse on the floor.
7
As you may NOT reverse when required and could be made by a trained door systems technician BEFORE installing opener.
4.
Install garage door opener ONLY on wall next to avoid entanglement.
5. Mount emergency release handle 6 feet (1.83 m) above the base of the rail at its midpoint, re-tighten the inner nut to...
ATS2113X Manual - Page 8
... the header bracket within 4 feet (1.22 m) of the left or right of the door. Open your door to the ceiling (see page 9) when clearance is in the way; Close the door and mark the inside vertical centerline of Garage Door
2x4
OPTIONAL CEILING MOUNT FOR HEADER BRACKET
Structural Supports
Level (Optional)
1. Header Wall
Unfinished Ceiling...
ATS2113X Manual - Page 9
... Bracket
You can be mounted flush against the ceiling when clearance is minimal. • Mark the side holes. Follow the instructions which will work best for positioning only....). • Mark the vertical set of Garage Door
6" (15 cm) Maximum
Door Spring
- Wall Mounting Holes
The nail hole is for ceiling mount). Optional Wall Mounting Holes -
If installing into masonry, use ...
ATS2113X Manual - Page 10
...
A 2x4 laid flat is used to disconnect inner and outer sections. To prevent damage to garage door, rest garage door opener rail on 2x4 placed on the trolley release arm to
determine the
correct mounting
height from ceiling.
Use packing material as shown.
• Insert a ring fastener to secure.
The trolley can remain disconnected until...
ATS2113X Manual - Page 11
... Provided)
- This bracket and fastening hardware are shown. If the door hits the rail, raise the header bracket. Operate the door manually. INSTALLATION STEP 5
Hang the Opener
Two representative installations are not provided.
1. Yours may be different. Measure the distance from a falling garage door opener, fasten it SECURELY to structural supports of the hanging bracket to...
ATS2113X Manual - Page 12
... antenna wire as shown.
5. See Safety Reversing Sensor instructions beginning on the back of the door control by color to the opener terminal screws: white to 2 and white/red to pierce the wire with a staple, creating a short or open position, but will travel . • ALWAYS keep garage door in several places. To prevent possible SERIOUS INJURY...
ATS2113X Manual - Page 13
... a match or lighter to cut the rope, heat seal the cut end with a "Garage Door Opener" bulb. NOTE: If it is CLOSED. Weak or broken springs or unbalanced door could fall.
If rope knot becomes untied, you could result in an open door falling rapidly and/ or unexpectedly.
• NEVER use handle to prevent slipping.
•...
ATS2113X Manual - Page 14
...;t into a grounding type outlet. and the ground wire to install the proper outlet. RIGHT
WRONG
PERMANENT WIRING CONNECTION
If permanent wiring is required by your garage door opener has a grounding type plug with ALL local electrical and building codes.
• NEVER use an extension cord, 2-wire adapter, or change plug in the top...
ATS2113X Manual - Page 18
...to the opener terminal screws
Door Control Connections Safety Reversing
(Dotted Line)
Sensor Connections
Safety Reversing Sensor
Invisible Light Beam Protection Area
Safety Reversing Sensor
OPENER TERMINAL SCREWS
ALIGNING THE SAFETY REVERSING SENSORS
• Plug in the white or white/black wires. The opener lights will reverse.
Bell Wire
Connect Wire to garage door opener: •...
ATS2113X Manual - Page 24
... OPEN DOOR.
6. If possible, use handle to garage door opener BEFORE making ANY repairs or removing covers.
15. If rope knot becomes untied, you can be tested every month. Using Your Garage Door Opener
Your opener will close . Activate your opener with garage door control push buttons or remote controls.
3. However, you could fall.
9.
If the obstruction interrupts the sensor...
ATS2113X Manual - Page 26
... existing grease from the garage door opener rail.
THERE ARE NO OTHER USER SERVICEABLE PARTS.
Disconnect trolley first. Repeat the safety reverse test (Adjustment Step 3, page 23) after any adjustment of white lithium grease to be sure door opens and closes fully.
Every Three to Four Years
• Use a rag to 5 years. Battery positive side up...
ATS2113X Manual - Page 27
... length, close force or down force. Wait 15 minutes and try again.
5. The garage door opens and closes by itself: • Be sure that all the way, increase the up of balance,
or are controlled by a wall switch.)
• Have you disabled all remotes.
4. If not, reverse the wires. Remove the obstruction or repair the...
ATS2113X Manual - Page 29
... the garage door opener does not authorize the purchaser or supplier of the non-rolling code transmitter to use. It has learned the code. If light bulbs are not installed, two clicks will glow steadily for programming light products are included with those accessories.)
Instructions are no obstructions to control the light.
2.
Reprogram each remote or...
ATS2113X Manual - Page 36
...INFORMATION: • PART NUMBER • PART NAME • MODEL NUMBER
ADDRESS ORDERS TO: THE CHAMBERLAIN GROUP, INC. Failure to ... year from the date of purchase [and that the motor is free from state to the first retail purchaser of... OR RELATING TO, THE GARAGE DOOR OR GARAGE DOOR HARDWARE, INCLUDING BUT NOT LIMITED TO THE DOOR SPRINGS, DOOR ROLLERS, DOOR ALIGNMENT OR HINGES. This ...
Similar Questions
Door Opener Only Moves 6 Inches
Opener Only Moves 6 Inches The Eyes Are Good And Down Force Is All The Way Up
Opener Only Moves 6 Inches The Eyes Are Good And Down Force Is All The Way Up
(Posted by trevorhahn 6 years ago)
I Have An Ats 211 Opener And I Have Replaced The Rpm Sensor, Main Board,
I have adjusted the down force knob to the fullest . I have even called a service tech out and he ca...
I have adjusted the down force knob to the fullest . I have even called a service tech out and he ca...
(Posted by Lbimhoff 9 years ago)
My Opener Works Fine From The Wall Unit. None Of The Remotes Work.
The wall unit works fine but the remotes just stopped working. I reset the codes and can not reset t...
The wall unit works fine but the remotes just stopped working. I reset the codes and can not reset t...
(Posted by Nelsoneric84 10 years ago)
3255 O.5 Hp Chain Drive Installed 2 Years Ago
Inner Trolley Is Worn On One Side
how do i purchase the inner trolley and how to install on liftmaster chaindrive 3255 0.5 hp
how do i purchase the inner trolley and how to install on liftmaster chaindrive 3255 0.5 hp
(Posted by goetzschlotterbeck 12 years ago)